Driver điều khiển độ sáng đèn LED với điện áp không đổi 1-10V điều chỉnh độ sáng 350mA-1050mA - Merrytek - ML50C-PV

THÔNG TIN THAM KHẢO

• Danh mục Model sản phẩm MERRYTEK

• 

  Phân biệt 4 kiểu điều khiển cường độ ánh sáng đèn LED: Triac, 0-10V, DALI, PWM Dimming

• 

  Danh sách các Model Dimmable LED Driver của Merrytek

• Xem thêm

Chi tiết thông tin đặc tính sản phẩm

Driver điều khiển độ sáng đèn LED với điện áp không đổi 1-10V điều chỉnh độ sáng 350mA-1050mA - Merrytek - ML50C-PV

 

Basic Information

Place of Origin: China
Brand Name: Merrytek
Certification: SEMKO /CE /RoHS
Model Number: ML50C-PV

 

Detail Information

Output Voltage: 68Vdc Max
Input Voltage: 220-240Vac
Dimming Mode: 0-10V,push
Production Name: Dimming Led Driver
Output Current: 350-1050mA Selectable Via DIP Switch
Input Current: 0.26mA Max
Output Load Range: 50W Max
Protection Class: IP20
Life Time: 50000hours
Certification: SEMKO /CE /RoHS

 

Product Description

ML50C-PV  1x50w 0-10V and push dimmable led driver 350mA to 1050mA multi-output 123x79x23.5mm for LED Panel Light
 
Feature
1. Output current and output voltage can be set by DIP switches, constant output current range from 350mA to 1050mA
2. Two circuit design AC-DC-DC, no flicckering in dimming 2%-100%
3. Stand-by power below 0.5W
4. Dimmable LED driver with primary PUSH, secondary PUSH and 1-10V dimming interface
5. Jumper design for switching different dimming modes, it is very convenient to select suitable dimming function as you required
6. Memory function: The driver has built-in permanent memory against power failure. Lights can return to previous dimming level when switch off and on again, even at mains restores
7. Synchronization: thanks to the MCU programme, up to 15pcs drivers should be controlled by the same switch. This means there is no need for any additional synchrony wire in larger installations, where many drivers should be controlled by one switch
8. Maximum length of the cable, from switch to last driver is 20m
9. Factory setting: 100% dimming level and 350mA output
10. Dim via a potentiometer
11. Support master-slave grouping net work
12. Protection: Short circuit / Over voltage / Over temperature
13. Long life span 50,000h, 5 years guaranty
14. Derating current for over high ambient temperature
 
Mechanical Specification


Dimming Operation
1. Push button switch for dimming (see wiring diagram, Fig A & Fig B)
    - ON/OFF: Short push (120ms ~ 1sec) on the switch
    - Stepless dimming: Long push (＞1sec) on the switch. With every other long push, the light level goes the opposite direction.
    - Synchronization: No need additional synchrony wire in larger installation, up to 15pcs drivers when connected to the same switch.

2. 1-10V dimming (see wiring diagram, Fig C)
The driver supports any active 1-10V dimmer. When the dimming signal is less than 0.8V ~ 1V or short the dimming wires, the output of LED driver could be completely switch off, see Fig C

Specifications

INPUT	Input voltage	220-240Vac
	Input frequency	50-60Hz
	Input current	0.26A max
	Power factor (Note 1)	≥0.90
	Efficiency(Note1)	≥86%
	Stand-by power (Note 2)	≤0.5W
OUTPUT	Output current/ voltage	350mA 6~60V DC 21W max.; 500mA 6~58V DC 29W max
		550mA 6~58V DC 31.9W max.; 650mA 6~58V DC 37.7W max.
		700mA 6~58V DC 40.6W max.; 750mA 6~56V DC 42W max
		850mA 6~56V DC 47.6W max.; 900mA 6~56V DC 50.4W max
		1050mA 6~48V DC 50.4W max.
		12V (0~1050mA) 12.6W max.; 24V (0~1050mA) 25.2W max.
	Output load range	50.4W Max.
	Current accuracy	±5%
	Dimming mode	1-10V, PUSH
ENVIRONMENT	Working temp.(Ta)	-20~50℃
	Surface temp.(Tc)	85℃max
	Working humidity	20~85%RH non-condensing
	Storage temp.	-40~80℃
	Life time	≥50000hours
PROTECTION	Isolation class	Class Ⅰ
	Protection class	IP20
	Over voltage	300Vac, 2H
	Short circuit	Protection type; auto reset
	No-load	Protection type; auto reset
	Over temperature	Protection type; auto reset
OTHERS	Safety	EN61347-1 EN61347-2-13
	EMC	EN55015, EN61000-3-2
		EN61000-3-3, EN61547
	Approvals	SEMKO, CE, RoHS
	Withstand voltage	IN-OUT:3.75KVAC/5mA/1min
	Dimension (L x W x H)	123x79x23.8mm
	Connection	Press-in type terminals, 0.75-1.5mm2
		Input: L, N, PUSH, PE
		Output: SEC(+) SEC(-), 1-10V(+),1-10V(-)
NOTE	Note:
	1, Power factor and efficiency is detected at 230Vac input and full load.
	2, Standby power is detected at 230Vac input and switch off led load by push button.

Applications
For LED panel light, LED down light, led strip, led tube etc…
 
 
Wire diagram
 

- Xem Tài liệu kỹ thuật Datasheet Catalogue Driver điều khiển độ sáng đèn LED với điện áp không đổi 1-10V điều chỉnh độ sáng 350mA-1050mA - Merrytek - ML50C-PV

Tag: #led light driver, #700ma dimmable led driver