Bộ lặp tín hiệu cấp nguồn Phoenix Contact MINI MCR-2-RPSS-I-2I-PT - 2905629

Bộ lặp tín hiệu cấp nguồn Phoenix Contact MINI MCR-2-RPSS-I-2I-PT - 2905629

551
Nhà sản xuất:

Phoenix Contact

;   

Xuất xứ: Germany

Giá sỉ:

Giá tốt nhất xem...0909186879 dienelectrics@gmail.com

Khuyến mãi:Có Discount
Bảo hành:12 Tháng (Chính hãng)
Thanh toán:C.O.D / Bảo lãnh TT / Link hoạt
Vận chuyển:Miễn phí Tp.HCM, vùng lân cận
Thông tin nổi bật

Bộ lặp tín hiệu cấp nguồn Phoenix Contact MINI MCR-2-RPSS-I-2I-PT - 2905629

4-way power supply doubler with plug-in connection technology. HART-transparent, 0(4) mA ... 20 mA input signal, 0(4) mA ... 20 mA output signals. The device can be used in both signal and power supply doubler modes. Push-in connection technology.

 

 

Mô tả

The power supply duplicator with plug-in connection technology supplies the transmitter in the field and electrically isolates the input signal transmitted to two loads. HART data protocols can be transmitted bi-directionally via both outputs. You can use the device in signal and power supply duplicator mode with a transmitter supply voltage of >19.5 V. On the output side, the module can be connected to passive input cards. For a maximum load of ≤500 Ω per channel, electrically isolated analog standard signals 0  mA ... 20 mA or 4  mA ... 20 mA are available. The measuring transducer supports fault monitoring and NFC communication.
 

Thống số kỹ thuật

Notes

Utilization restriction
EMC note EMC: class A product, see manufacturer's declaration in the download area
 

Product properties

Product type Repeater power supplies
Product family MINI Analog Pro
No. of channels 2
Type Signal conditioner
Configuration DIP switches
Insulation characteristics: GB Standard
Overvoltage category II
Pollution degree 2
 

Electrical properties

No. of channels 2
Electrical isolation 4-way isolation
Limit frequency (3 dB) > 1 kHz
Signal transmission behavior In = Out
Step response (10-90%) < 400 µs
Maximum temperature coefficient 0.0075 %/K
Maximum transmission error 0.05 % (of final value)
Electrical isolation Input/output/power supply
Rated insulation voltage 300 Vrms
Test voltage 3 kV AC (50 Hz, 60 s)
Insulation Reinforced insulation according to IEC/EN 61010-1
Supply
Nominal supply voltage 24 V DC
Supply voltage range 9.6 V DC ... 30 V DC (The DIN rail connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, item no. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail in accordance with EN 60715)
Typical current consumption 40 mA (For 24 V DC and in signal duplicator mode)
65 mA (For 24 V DC and in power supply duplicator mode)
75 mA (For 12 V DC and in signal duplicator mode)
130 mA (For 12 V DC and in power supply duplicator mode)
Power consumption 1.6 W (at IOUT = 20 mA, 500 Ω load)
 

Input data

Signal: Current
Description of the input Sensor circuit
Number of inputs 1
Current input signal 0 mA ... 20 mA (Signal duplicator mode)
4 mA ... 20 mA (Power supply and signal duplicator mode)
Input resistance current input 90 Ω (+1.6 V)
Transmitter supply voltage > 19.5 V
 

Output data

Signal: Current
Number of outputs 2
Non-load voltage < 20 V
Current output signal 0 mA ... 20 mA (Signal duplicator mode)
4 mA ... 20 mA (Power supply and signal duplicator mode)
Max. current output signal 25 mA
Load/output load current output ≤ 500 Ω (per channel)
Ripple < 20 mVPP (500 Ω)
 

Connection data

Connection method Push-in connection
Stripping length 10 mm
Conductor cross section rigid 0.2 mm² ... 2.5 mm² (with ferrule)
0.14 mm² ... 2.5 mm² (without ferrule)
Conductor cross section flexible 0.14 mm² ... 2.5 mm²
Conductor cross section AWG 24 ... 12 (flexible)
 

Ex data

Ex installation (EPL) Gc
Div. 2
 

Interfaces

Data communication (bypass)
HART function Yes
Limit frequency (3 dB)  1 kHz
 

Signaling

Status display Green LED (supply voltage)
 

Dimensions

Width 6.2 mm
Height 109.81 mm
Depth 119.2 mm
 

Material specifications

Fire protection for rail vehicles (DIN EN 45545-2) R22 HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R23 HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R24 HL 1 - HL 2
Housing material PBT
 

Environmental and real-life conditions

Ambient conditions
Degree of protection IP20 (not assessed by UL)
Ambient temperature (operation) -40 °C ... 70 °C
Ambient temperature (storage/transport) -40 °C ... 85 °C
Altitude ≤ 2000 m
Permissible humidity (operation) 5 % ... 95 % (non-condensing)
 

Approvals

CE
Certificate CE-compliant
ATEX
Identification  II 3 G Ex ec ic IIC T4 Gc
Certificate BVS 19 ATEX E 047 X
UKCA Ex (UKEX)
Identification  II 3 G Ex ec ic IIC T4 Gc
Certificate PxCIF21UKEX2902000X
IECEx
Identification Ex ec ic IIC T4 Gc
Certificate IECEx BVS 19.0041X
CCC / China-Ex
Identification Ex nA ic IIC T4 Gc
UL, USA/Canada
Identification UL 508 Listed
Class I, Div. 2, Groups A, B, C, D T5
Class I, Zone 2, Group IIC T5
Shipbuilding approval
Certificate DNV GL TAA000021E Rev. 1
EAC Ex
Identification  2Ex ec ic IIC T4 Gc
Certificate BY/112 02.01 TP012 103.01 00081
DNV GL data
Temperature B
Humidity B
Vibration A
EMC A
Enclosure Required protection according to the Rules shall be provided upon installation on board
 

EMC data

Noise immunity EN 61000-6-2
Note When being exposed to interference, there may be minimal deviations.
Electromagnetic compatibility Conformance with EMC directive
Noise emission EN 61000-6-4
Electrostatic discharge
Standards/regulations EN 61000-4-2
Electrostatic discharge
Comments Safety measures must be taken to prevent electrostatic discharge.
Electromagnetic HF field
Designation Electromagnetic RF field
Standards/regulations EN 61000-4-3
Fast transients (burst)
Designation Fast transients (burst)
Standards/regulations EN 61000-4-4
Surge current load (surge)
Standards/regulations EN 61000-4-5
Conducted interference
Designation Conducted interferences
Standards/regulations EN 61000-4-6
 

Standards and regulations

Electrical isolation 4-way isolation
GB Standard
Standards/regulations GB 3836.1
GB 3836.4
GB 3836.8
 

Mounting

Mounting type DIN rail mounting
Assembly instructions The DIN rail connector can be used for bridging the supply voltage. It can be snapped onto a 35 mm EN 60715 DIN rail.
Mounting position any
 

Commercial data

Item number 2905629
Packing unit 1 pc
Minimum order quantity 1 pc
Product key CK1411
Catalog page Page 78 (C-5-2019)
GTIN 4046356999441
Weight per piece (including packing) 120.6 g
Weight per piece (excluding packing) 120 g
Customs tariff number 85437090
Country of origin DE
 

Classifications

ECLASS

ECLASS-11.0 27210120
ECLASS-12.0 27210120
ECLASS-13.0 27210120
 

ETIM

ETIM 9.0 EC002653
 

UNSPSC

UNSPSC 21.0 39121000
 

Approvals

EAC

Approval ID: RU*DE.*08.B.01608/19
 

DNV GL

Approval ID: TAA000021E
 

UL Listed

Approval ID: FILE E 238705
 

CCC

Approval ID: 2021322303003858
 

cUL Listed

Approval ID: FILE E 238705
 

IECEx

Approval ID: IECEx BVS 19.0041X
 

cUL Listed

Approval ID: FILE E 196811
 

UL Listed

Approval ID: FILE E 196811
 

ATEX

Approval ID: BVS 19 ATEX E 047 X
 

cULus Listed

 

cULus Listed



Environmental product compliance
 
REACh SVHC Lead 7439-92-1
 
China RoHS Environmentally Friendly Use Period = 50 years
For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”


- Tài liệu kỹ thuật Phoenix Contact MINI MCR-2-RPSS-I-2I-PT - 2905629 ở đây.


Tham khảo thêm các model khác cùng loại:
MACX MCR-T-UI-UP - Temperature measuring transducer
2811394

Freely programmable temperature transducer with analog output and 1 limit value relay, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.
MACX MCR-UI-UI-UP-NC - Signal conditioner
2811297

Isolating amplifier with safe electrical isolation and wide-range power supply (24 V ... 230 V AC/DC). DIP switches on the front, over 1600 signal conversions can be set. Standard configuration (IN 0 ... 10 V/OUT 0 ... 20 mA), screw connection, SIL.
MACX MCR-UI-UI-NC - Signal conditioner
2811446

Configurable 3-way isolating amplifier with safe electrical isolation, 24 V, power bridging. DIP switches on the front, over 1600 signal conversions can be set. Standard configuration (IN 0 ... 10 V/OUT 0 ... 20 mA), screw connection, SIL.
MACX MCR-UI-UI-UP-SP-NC - Signal conditioner
2811569

Isolating amplifier with safe electrical isolation and wide-range power supply (24 V ... 230 V AC/DC). DIP switches on the front, over 1600 signal conversions can be set. Standard configuration (IN 0 ... 10 V/OUT 0 ... 20 mA), spring-cage connection, SIL.
MACX MCR-SL-RPSSI-I - Power/input isolating amplifier
2865955

Repeater power supply and input signal conditioner, HART-transparent. Transmits supplied or active 0/4 … 20 mA signals to a load (active or passive). 3-way electrical isolation, SIL 2 in accordance with IEC 61508.
MACX MCR-UI-UI - Signal conditioner
2811284

Configurable 3-way isolating amplifier with safe electrical isolation, 24 V, power bridging. DIP switches on the front, over 1600 signal conversions can be set. Order configuration, screw connection, SIL.
MACX MCR-SL-I-I-ILP - Loop-powered isolators
2905278

1-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Screw connection technology.
MACX MCR-SL-RPSSI-2I - Repeater power supply
2924825

Measuring transducer repeater power supply and input signal conditioner, HART-transparent. Transmits supplied or active 0/4…20 mA electrically isolated signals from the field to two loads. 4-way electrical isolation, screw connection, SIL, PL.
MACX MCR-T-UIREL-UP - Temperature measuring transducer
2811378

Freely programmable temperature transducer with analog output and 3 limit value relays, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.
MACX MCR-SL-RPSSI-I-SP - Power/input isolating amplifier
2924207

Repeater power supply and input signal conditioner, HART-transparent. Transmits supplied or active 0/4 … 20 mA signals to a load (active or passive). 3-way electrical isolation, SIL 2 in accordance with IEC 61508.
MACX MCR-T-UI-UP-SP - Temperature measuring transducer
2811860

Freely programmable temperature transducer with analog output and 1 limit value relay, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.
MACX MCR-SL-NAM-R-SP - Isolation amplifier
2924252

NAMUR signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via relay output (changeover contact). Line fault detection (LFD), 3-way electrical isolation, SIL 2, with Push-in connection.
MACX MCR-SL-2NAM-RO - Isolation amplifier
2865049

NAMUR 2-channel signal conditioner for operating proximity sensors and switches. The signals are transferred to the control level using relay outputs (N/O contact). Line fault detection, 3-way electrical isolation, SIL 2, screw connection.
MACX MCR-SL-2NAM-R-UP - Isolation amplifier
2865052

2-channel NAMUR signal conditioner with wide range power supply for proximity sensors and switches. In terms of signal output, for each channel there is a relay with a changeover contact available. Line fault detection (LFD), 3-way isolation, screw connection, SIL 2.
MACX MCR-UI-UI-SP-NC - Signal conditioner
2811556

Configurable 3-way isolating amplifier with safe electrical isolation, 24 V, power bridging. DIP switches on the front, over 1600 signal conversions can be set. Standard configuration (IN 0 ... 10 V/OUT 0 ... 20 mA), spring-cage connection, SIL.
MACX MCR-RTD-I - Temperature measuring transducer
1050192

Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, screw connection, SIL, 3-way electrical isolation, standard configuration.
MACX MCR-SL-RPSS-2I-2I - Repeater power supply
2904089

2-channel repeater power supply for operating 2-conductor measuring transducers, input: 4 ... 20 mA (supplying), output: 4 ... 20 mA (active), bidirectional transmission with digital HART transparency, screw connection, SIL, PL.
MACX MCR-SL-2NAM-RO-SP - Isolation amplifier
2924294

NAMUR 2-channel signal conditioner for operating proximity sensors and switches. The signals are transferred to the control level using relay outputs (N/O contact). Line fault detection, 3-way electrical isolation, SIL 2, Push-in connection.
MACX MCR-IDS-I-I-SP - Output signal conditioner
2908064

Output signal conditioner, HART-transparent. Isolates and transmits 0/4 mA ... 20 mA signals to a load in the safe area. 3-way electrical isolation, line fault detection (can be switched off via DIP switch), SIL 2 (SC3) in accordance with IEC 61508, Push-in connection.
MACX MCR-SL-NAM-2RO - Isolation amplifier
2865010

NAMUR signal conditioner for operating proximity sensors and switches. The signals are transferred to the control level using 2 isolated relay outputs (N/O contact). Line fault detection (LFD), 3-way electrical isolation, SIL 2, screw connection.
MACX MCR-T-UIREL-UP-SP - Temperature measuring transducer
2811828

Freely programmable temperature transducer with analog output and 3 limit value relays, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.
MACX MCR-SL-2I-2I-ILP - Loop-powered isolators
2905280

2-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Screw connection technology.
MACX MCR-SL-NAM-R - Isolation amplifier
2865997

NAMUR signal conditioners for operating proximity sensors and switches. The signals are transmitted to the control level via relay output (changeover contact). Line fault detection (LFD), 3-way electrical isolation, SIL 2, with screw connection.
MACX MCR-SL-2NAM-R-UP-SP - Isolation amplifier
2924304

2-channel NAMUR signal conditioner with wide range power supply for proximity sensors and switches. In terms of signal output, for each channel there is a relay with a changeover contact available. Line fault detection (LFD), 3-way isolation, Push-in connection, SIL 2.
MACX MCR-SL-RPSSI-I-UP-SP - Repeater power supply
2924210

Repeater power supply for supplying 2- and 3-conductor transmitters with HART transparency and wide-range power supply, SIL 2 (1oo1)/SIL 3 (1oo2), Push-in connection
MACX MCR-SL-NAM-2RO-SP - Isolation amplifier
2924265

NAMUR signal conditioner for operating proximity sensors and switches. The signals are transferred to the control level using 2 isolated relay outputs (N/O contact). Line fault detection (LFD), 3-way electrical isolation, SIL 2, Push-in connection.
MACX MCR-SL-RPSSI-I-UP - Repeater power supply
2865968

Repeater power supply for supplying 2- and 3-conductor transmitters with Hart transparency and wide-range power supply, SIL 2 (1oo1)/SIL 3 (1oo2), screw connection
MACX MCR-RTD-I-SP - Temperature measuring transducer
1050201

Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, Push-in connection, SIL, 3-way electrical isolation, standard configuration.
MACX MCR-SL-NAM-2T - Isolation amplifier
2865023

NAMUR signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via 2 transistor outputs (passive). Line fault detection, 3-way electrical isolation, SIL 2, screw connection.
MINI MCR-SL-PT100-UI-NC - Resistance thermometer measuring transducer
2864273

MCR temperature transducer for Pt 100 temperature sensors, configured via DIP switches, with screw connection, not preconfigured
MACX MCR-T-UI-UP-C - Temperature measuring transducer
2811873

Freely programmable temperature transducer with analog output and 1 limit value relay, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.
MACX MCR-SL-RPSS-2I-2I-SP - Repeater power supply
2904090

2-channel repeater power supply for operating 2-conductor measuring transducers, input: 4 ... 20 mA (supplying), output: 4 ... 20 mA (active), bidirectional transmission with digital HART transparency, Push-in connection, SIL, PL.
MACX MCR-UI-UI-UP - Signal conditioner
2811459

Configurable 3-way isolating amplifier with safe electrical isolation and wide-range power supply (24 V ... 230 V AC/DC). DIP switches on the front, over 1600 signal conversions can be set. Order configuration, screw connection, SIL.
MINI MCR-SL-UI-2I-NC - Signal duplicator
2864176

4-way signal duplicator for electrical isolation and duplication of analog signals with screw connection, standard configuration
MINI MCR-SL-R-UI - Resistance/potiposition transducer
2864095

MCR potiposition transducer for conversion of potentiometer positions into a standard analog signal, 0 Ω input... 100 Ω to 0 kΩ ... 100 kΩ
MINI MCR-2-UI-UI-PT - Signal conditioner
2902040

3-way signal conditioner with plug-in connection technology and calibrated measuring range changeover, for the electrical isolation of unipolar and bipolar analog signals. Input/output configurable via DIP switch. push-in connection technology, standard configuration.
MINI MCR-2-UNI-UI-2UI-PT - Signal duplicator
2905028

Universally configurable 4-way signal duplicator, with plug-in connection technology for the electrical isolation and duplication of analog signals. Configurable via DIP switch or software. Push-in connection technology, standard configuration.
MINI MCR-SL-I-I - Signal conditioner
2864406

MCR 3-way isolating amplifier, for electrical isolation of analog signals, with screw connection, input signal: 0(4) mA ... 20 mA, output signal: 0(4) mA ... 20 mA
MINI MCR-SL-UI-UI-NC - Signal conditioner
2864150

3-way isolating amplifier for the electrical isolation of analog signals, I/O can be configured via DIP switches, with screw connection, standard configuration
MINI MCR-2-UNI-UI-2UI - Signal duplicator
2905026

Universally configurable 4-way signal duplicator, with plug-in connection technology for the electrical isolation and duplication of analog signals. Configurable via DIP switch or software. Screw connection technology, standard configuration.
MINI MCR-SL-RPS-I-I - Repeater power supply
2864422

MCR repeater power supplies, screw connection, input signal: (0)4..20 mA, output signal: (0)4..20 mA
MINI MCR-SL-RPSS-I-I - Repeater power supply
2864079

MCR repeater power supply with HART transparency, input signal: 4 mA ... 20 mA, output signal: 4 mA ... 20 mA, with screw connection
MINI MCR-2-UI-UI - Signal conditioner
2902037

3-way signal conditioner with plug-in connection technology and calibrated measuring range changeover for the electrical isolation of unipolar and bipolar analog signals. Input/output configurable via DIP switch. Screw connection technology, standard configuration.
MINI MCR-2-RTD-UI - Resistance thermometer measuring transducer
2902049

Configurable temperature transducer with plug-in connection technology for connecting 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Configurable via DIP switch or software. Screw connection technology, standard configuration
MINI MCR-2-I-I - Signal conditioner
2901998

3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 0(4) mA ... 20 mA, output signal: 0(4) mA ... 20 mA, screw connection technology
MINI MCR-2-U-U - Signal conditioner
2902042

3-way signal conditioner with plug-in connection technology for the electrical isolation of unipolar and bipolar analog signals. Input signal: 0 ... 10 V/±10 V, output signal: 0 ... 10 V/±10 V, screw connection technology
MINI MCR-2-F-UI - Frequency measuring transducer
2902056

Universally configurable frequency transducer for converting frequency (Hz/rpm) and PWM signals into standard signals. Sensor voltages greater than 8.2 V DC are possible in combination with MINI MCR-2-SPS 1033202. Screw connection technology.
MINI MCR-SL-PT100-LP-NC - Temperature measuring transducer
2810308

Configurable loop-powered temperature transducer for Pt 100 temperature sensors, configured via DIP switches, with screw connection, not preconfigured
MACX MCR-SL-2NAM-T - Isolation amplifier
2865036

NAMUR 2-channel signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via transistor outputs (passive). Line fault detection, 3-way electrical isolation, SIL 2, screw connection.
MACX MCR-SL-RPSSI-2I-SP - Repeater power supply
2924838

Measuring transducer repeater power supply and input signal conditioner, HART-transparent. Transmits supplied or active 0/4 mA … 20 mA electrically isolated signals from the field to two loads. 4-way electrical isolation, Push-in connection, SIL, PL.
MINI MCR-TC-UI-NC - Thermocouple measuring transducer
2902851

Configurable temperature transducer for the connection of thermocouples. Can be configured via DIP switches or, with extended functionality, using the software. Screw connection, standard configuration.
MINI MCR-SL-1CP-I-I - Loop-powered isolators
2864419

MCR loop-powered isolator, 1-channel, for the electrical isolation of current signals without auxiliary power, with screw connection
MINI MCR-2-RPSS-I-2I-PT - Repeater power supply
2905629

4-way power supply doubler with plug-in connection technology. HART-transparent, 0(4) mA ... 20 mA input signal, 0(4) mA ... 20 mA output signals. The device can be used in both signal and power supply doubler modes. Push-in connection technology.
MINI MCR-2-RPSS-I-I-PT - Repeater power supply
2902015

3-way repeater power supply with plug-in connection technology. HART-transparent, input signal 0(4) mA ... 20 mA, output signal 0(4) mA ... 20 mA. The device can be used in both isolator and repeater power supply operation. push-in connection technology
MINI MCR-2-RTD-UI-PT - Resistance thermometer measuring transducer
2902052

Configurable temperature transducer with plug-in connection technology for connecting 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Configurable via DIP switch or software. push-in connection technology, standard configuration
MINI MCR-2-I-I-ILP - Loop-powered isolators
2901994

1-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Screw connection technology.
MINI MCR-2-TC-UI - Thermocouple measuring transducer
2902055

Configurable temperature transducer with plug-in connection technology for connecting thermocouples. Configurable via DIP switch or software. Screw connection technology, standard configuration
MINI MCR-SL-2CP-I-I - Loop-powered isolators
2864655

MCR passive isolator, 2-channel, for the electrical isolation of current signals without auxiliary power, with screw connection
MINI MCR-SL-PT100-UI-200-NC - Temperature measuring transducer
2864370

MCR temperature transducer, configurable, for Pt 100 temperature sensors, with screw-connection, not configured
MINI MCR-RTD-UI-NC - Resistance thermometer measuring transducer
2902849

Configurable temperature transducer for the connection of 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Can be configured via DIP switches or, with extended functionality, using the software. Screw connection, standard configuration.
MACX MCR-SL-I-I-ILP-SP - Loop-powered isolators
2905279

1-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
MACX MCR-RTD-I-C - Temperature measuring transducer
1052472

Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, screw connection, SIL, 3-way electrical isolation, order configuration.
MACX MCR-RTD-I-SP-C - Temperature measuring transducer
1052464

Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, Push-in connection, SIL, 3-way electrical isolation, order configuration.
MACX MCR-T-UI-UP-SP-C - Temperature measuring transducer
2811970

Freely programmable temperature transducer with analog output and 1 limit value relay, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.
MACX MCR-UI-UI-UP-SP - Signal conditioner
2811585

Configurable 3-way isolating amplifier with safe electrical isolation and wide-range power supply (24 V ... 230 V AC/DC). DIP switches on the front, over 1600 signal conversions can be set. Order configuration, spring-cage connection, SIL.
MACX MCR-SL-2I-2I-ILP-SP - Loop-powered isolators
2905281

2-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
MACX MCR-T-UIREL-UP-SP-C - Temperature measuring transducer
2811831

Freely programmable temperature transducer with analog output and 3 limit value relays, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.
MACX MCR-SL-2NAM-T-SP - Isolation amplifier
2924281

NAMUR 2-channel signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via transistor outputs (passive). Line fault detection, 3-way electrical isolation, SIL 2, Push-in connection.
MACX MCR-TC-I-C - Temperature measuring transducer
1052459

Temperature transducer: converts signals from thermocouples and mV sources into 0/4…20 mA signals. Order configuration, freely programmable, 3-way electrical isolation, screw connection, SIL.
MACX MCR-SL-NAM-2T-SP - Isolation amplifier
2924278

NAMUR signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via 2 transistor outputs (passive). Line fault detection, 3-way electrical isolation, SIL 2, Push-in connection.
MACX MCR-IDS-2I-2I-SP - Output signal conditioner
2908066

2-channel output signal conditioner, HART-transparent. Isolates and transmits 0/4 mA ... 20 mA signals to a load in the safe area. 4-way electrical isolation, line fault detection, SIL 2 (SC3) in accordance with IEC 61508, Push-in connection.
MACX MCR-TC-I - Temperature measuring transducer
1050228

Temperature transducer: converts signals from thermocouples and mV sources into 0/4…20 mA signals. Freely programmable, 3-way electrical isolation, screw connection, SIL.
MACX MCR-UI-UI-SP - Signal conditioner
2811572

Configurable 3-way isolating amplifier with safe electrical isolation, 24 V, power bridging. DIP switches on the front, over 1600 signal conversions can be set. Order configuration, spring-cage connection, SIL.
MACX MCR-IDS-2I-2I - Output signal conditioner
2908065

2-channel output signal conditioner, HART-transparent. Isolates and transmits 0/4 mA ... 20 mA signals to a load in the safe area. 4-way electrical isolation, line fault detection, SIL 2 (SC3) in accordance with IEC 61508, screw connection.
MACX MCR-T-UIREL-UP-C - Temperature measuring transducer
2811514

Freely programmable temperature transducer with analog output and 3 limit value relays, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.
MACX MCR-IDS-I-I - Output signal conditioner
2908063

Output signal conditioner, HART-transparent. Isolates and transmits 0/4 mA ... 20 mA signals to a load in the safe area. 3-way electrical isolation, line fault detection (can be switched off via DIP switch), SIL 2 (SC3) in accordance with IEC 61508, screw connection.
MINI MCR-2-U-I4-PT - Signal conditioner
2902030

3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 0 V ... 10 V, output signal: 4 mA ... 20 mA, push-in connection technology
MINI MCR-SL-I-U-4 - Signal conditioner
2813538

MCR 3-way isolating amplifier, for electrical isolation of analog signals, with screw connection, input signal: 4 mA ... 20 mA, output signal: 0 A ... 10 V
MINI MCR-SL-CVS-24-5-10-NC - Constant voltage source
2902822

Constant voltage source, input voltage 9.6 - 30 V DC, output voltage 10 V, 7.5 V, 5 V, 2.5 V DC, electrically isolated, can be configured via DIP switches, screw connection technology, standard configuration
MINI MCR-2-I-I-PT - Signal conditioner
2901999

3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 0(4) mA ... 20 mA, output signal: 0(4) mA ... 20 mA, push-in connection technology.
MINI MCR-SL-F-UI-NC - Frequency measuring transducer
2902832

The configurable frequency transducer is suitable for the connection of NAMUR proximity sensors as well as for sensors with NPN and PNP outputs. Configurable via DIP switch and teach-in wheel. Screw connection, standard configuration.
MINI MCR-SL-IDS-I-I - Output signal conditioner
2905577

3-way output signal conditioner for transmitting 0/4 ... 20 mA signals from the controller to a load located in the field with simultaneous 3-way electrical isolation between the input, output, and supply, with screw connection
MINI MCR-SL-SHUNT-UI-NC - Signal conditioner
2810780

MCR 3-way signal conditioner, with configurable input/output, for electrical isolation and conversion of analog signals in the mV range, both unipolar and bipolar with screw connection, not preconfigured
MINI MCR-2-RPSS-I-2I - Repeater power supply
2905628

4-way power supply doubler with plug-in connection technology. HART-transparent, 0(4) mA ... 20 mA input signal, 0(4) mA ... 20 mA output signals. The device can be used in both signal and power supply doubler modes. Screw connection technology.
MINI MCR-2-UI-UI-C - Signal conditioner
2902036

3-way signal conditioner with plug-in connection technology and calibrated measuring range changeover for the electrical isolation of unipolar and bipolar analog signals. Input/output configurable via DIP switch. Screw connection technology, order configuration.
MINI MCR-2-U-I4 - Signal conditioner
2902029

3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 0 V ... 10 V, output signal: 4 mA ... 20 mA, screw connection technology
MINI MCR-2-POT-UI - Resistance/potiposition transducer
2902016

Configurable potiposition transducer with plug-in connection technology for connecting potentiometers from 0 Ω ... 100 Ω to 0 kΩ ... 100 kΩ. Configurable via DIP switch or software. Screw connection technology, standard configuration
MINI MCR-2-POT-UI-PT - Resistance/potiposition transducer
2902017

Configurable potiposition transducer with plug-in connection technology for connecting potentiometers from 0 Ω ... 100 Ω to 0 kΩ ... 100 kΩ. Configurable via DIP switch or software. push-in connection technology, standard configuration
MINI MCR-SL-UI-I-LP-NC - Signal conditioner
2902829

2-way loop-powered isolating amplifier (supplied on the output side), can be configured via DIP switches, with screw connection technology and standard configuration.
MINI MCR-SL-U-UI-NC - Signal conditioner
2865007

MCR 3-way signal conditioner, with configurable input/output, for electrical isolation and conversion of analog signals up to 30 V, with screw connection, standard configuration
MINI MCR-2-U-UI - Signal conditioner
2902019

3-way signal conditioner, with configurable input/output, for electrical isolation and conversion of analog signals in the mV and V range, unipolar as well as bipolar. Screw connection technology, standard configuration.
MINI MCR-2-UI-I-OLP - Loop-powered isolators
2902061

Output loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of unipolar and bipolar analog signals. Input configurable via DIP switch. Screw connection technology, standard configuration.
MINI MCR-SL-UI-REL - Limit value switch
2864480

MCR limit value switch, with adjustable hysteresis and delay time, with screw connection
MINI MCR-SL-UI-F - Frequency measuring transducer
2864082

Analog frequency transducers for converting analog standard signals into frequency signals or PWM signals, configurable via DIP switch, with screw connection
MACX MCR-SL-UI-REL-SP - Limit value switch
2906170

Limit value switch with input for active current and voltage signals and a limit-value relay output (changeover contact). Can be set via DIP switch and potentiometer, galvanic 3-way electrical isolation, up to SIL2 (SC3), PLc Cat.1, Push-in connection.
MINI MCR-2-I4-U-PT - Signal conditioner
2902003

3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 4 mA ... 20 mA, output signal: 0 V ... 10 V, push-in connection technology
MINI MCR-SL-U-I-4 - Signal conditioner
2813525

MCR 3-way isolating amplifier, for electrical isolation of analog signals, with screw connection, input signal: 0 V ... 10 V, output signal: 4 mA ... 20 mA
MINI MCR-2-UI-FRO-PT - Frequency measuring transducer
2902032

Analog frequency transducer with limit value functionality and plug-in connection technology for converting standard signals into frequency or PWM signals. Configurable via DIP switch or software. Push-in connection technology, standard configuration.
MINI MCR-2-U-UI-PT - Signal conditioner
2902021

3-way signal conditioner, with configurable input/output, for electrical isolation and conversion of analog signals in the mV and V range, unipolar as well as bipolar. Push-in connection technology, standard configuration.
MINI MCR-2-UNI-UI-UIRO - Signal conditioner
2902026

Universally configurable 4-way signal conditioner, with switching output and plug-in connection technology for the electrical isolation of analog signals. Configurable via DIP switch or software. Screw connection technology, standard configuration.
MINI MCR-2-UI-REL-PT - Limit value switch
2902035

Universally configurable threshold value switch with changeover contact relay output and plug-in connection technology for switching analog limit values. Configurable via DIP switch or software. Push-in connection technology, standard configuration.
MINI MCR-2-2I-2I-ILP-PT - Loop-powered isolators
2901997

2-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
MINI MCR-2-TC-UI-PT - Thermocouple measuring transducer
2905249

Configurable temperature transducer with plug-in connection technology for connecting thermocouples. Configurable via DIP switch or software. Push-in connection technology, standard configuration
MINI MCR-2-RTD-UI-C - Resistance thermometer measuring transducer
2902048

Configurable temperature transducer with plug-in connection technology for connecting 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Configurable via DIP switch or software. Screw connection technology, order configuration
MINI MCR-2-F-UI-PT - Frequency measuring transducer
2902058

Universally configurable frequency transducer for converting frequency (Hz/rpm) and PWM signals into standard signals. Sensor voltages greater than 8.2 V DC are possible in combination with MINI MCR-2-SPS-PT 1033201. Push-in connection technology.
MINI MCR-2-RPS-2I-2I-OLP-PT - Repeater power supply
2906449

Two-channel output loop-powered 2-way repeater power supply with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
MINI MCR-2-NAM-2RO - Isolation amplifier
2902004

Configurable NAMUR signal conditioner with plug-in connection technology for proximity sensors, floating switch contacts, and switch contacts with resistance circuit. 2 transistor outputs, configurable via DIP switch. Screw connection technology.
MACX MCR-SL-I-I-HV-ILP-SP - Loop-powered isolators
2907705

1-channel input loop-powered 2-way isolator with increased isolating voltage and plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
MINI MCR-SL-I-U-0 - Signal conditioner
2813541

MCR 3-way isolating amplifier, for electrical isolation of analog signals, with screw connection, input signal: 0 mA ... 20 mA, output signal: 0 V ... 10 V
MINI MCR-2-UNI-UI-2UI-C - Signal duplicator
2905025

Universally configurable 4-way signal duplicator, with plug-in connection technology for the electrical isolation and duplication of analog signals. Configurable via DIP switch or software. Screw connection technology, order configuration.
MINI MCR-SL-U-U - Signal conditioner
2864684

MCR 3-way isolating amplifier, for electrical isolation of analog signals, with screw connection, input signal: 0 ... 10 V/±10 V, output signal: 0 ... 10 V/±10 V
MINI MCR-2-NAM-2RO-PT - Isolation amplifier
2902005

Configurable NAMUR signal conditioner with plug-in connection tec
SẢN PHẨM XEM NHIỀU
Circuit Breakers (CB) hoạt động thế nào?
Bộ ngắt điện hay còn gọi là máy cắt (Circuit breaker-CB) là thiết bị được thiết kế để bảo vệ một mạch điện khỏi bị hư hỏng gây ra bởi dòng điện
Tụ chống sét Varistor (MOVs)là gì? Nguyên lý hoạt động (Wiki)Tụ chống sét ( Varistor hoặc Metal Varistor Oxit (MOV)) là một điện trở đặc biệt được sử dụng để bảo vệ mạch điện chống lại sự đột biến điện áp
Hãy xem RCCB và ELCB cứu bạn thoát chết vì điện giựt thế nào!Hãy xem tầm qua trong của RCCB và ELCB trong việc cứu nạn nhân bị điện giựt thoát chết như thế nào..
Programmable logic controller
A programmable logic controller (PLC), or programmable controller is an industrial digital computer which has been ruggedisedand adapted for the control of
White paper về Lý thuyết điều khiển tự độngLý thuyết điều khiển tự động là một nhánh liên ngành của kỹ thuật và toán học, liên quan đến hành vi của
Hướng dẫn Lập trình PLC chi tiết cho người mới tìm hiểu (Part 1)Điều khiển quá trình (PLC) được sử dụng rộng rãi trong công nghiệp và cho phép sản xuất hàng loạt các sản phẩm phù hợp với các
Sensors In Agriculture (Comming soon)Sensors In Agriculture. Soil moisture sensors, Agricultural temperature sensors, GPS sensors, Weather sensors, Crop health sensors, Electronic sensors, Light
10 Dự báo về Internet Of Things (IoT) năm 2018Trong một báo cáo mới, dự đoán năm 2018: IoT chuyển từ thử nghiệm sang kinh doanh quy mô, Forrester Research dự đoán rằng IoT sẽ trở thành xương sống của
Top 15 Loại cảm biến Sensor được dùng nhiều trong các thiết bị IoTNền tảng IoT hoạt động và cung cấp các dạng thông minh và dữ liệu có giá trị với việc sử dụng nhiều cảm biến khác nhau. Chúng phục vụ để thu
Năng lượng tương lai: Photovoltaic hay Hydrogen?Hydrogen là một nguyên tố chiếm tỷ lệ cao nhất so với tất cả các nguyên tố khác trên địa cầu. Nhưng hydrogen không hiện diện dưới dạng nguyên tử hay
Năng lượng tái tạo : Một loại ắc quy mới nhiều hứa hẹnNăng lượng tái tạo như điện gió và điện mặt trời có một nhược điểm căn bản, đó là không ổn định. Chúng chỉ vận hành khi có
Chất thải từ người là năng lượng tương lai?BBC Future - Hành tinh của chúng ta gặp một vấn đề. Con người, như tất cả các sinh vật sống khác, thải ra rất nhiều những chất thải không dễ chịu
Tin vui cho phái đẹp: Robot Spermbot có thể giúp điều trị ung thư cổ tử cungKhi robot sinh học này phát hiện ra khối u, bốn cánh tay trên cấu trúc vi mô tự động uốn cong, giải phóng tế bào tinh trùng, xâm
Tương lai nào cho trí tuệ nhân tạo - Artificial intelligence (AI)?
Trí thông minh nhân tạo (AI) là khả năng của một chương trình máy tính hoặc một máy tính để suy nghĩ và học hỏi. Nó
Bạn Biết Có Bao Nhiêu Loại Robot - ROBOTPARK
Các loại Robot là gì? Dưới đây là các loại robot của hệ thống vận động. Chúng tôi sẽ kiểm tra các loại này một cách
Gọi điện thoại