Item/ Model | E2V-X2 - - |
Size | M12 |
Sensing distance | 2mm±10% |
Set distance | 0 to 1.6 mm |
Differential travel | 10% max. of sensing distance |
Detectable object | Ferrous metals and non-ferrous metals (The sensing distance depends on the material of the sensing object. Refer to Engineering Data (Typical).) |
Standard sensing object | Aluminum: 12 × 12 × 3 mm |
Response frequency* | 150Hz |
Power supply voltage (operating voltage range) |
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. |
Current consumption | 450 mW max. (Current consumption: 15 mA max. at power supply voltage of 30 V) |
Control output Load current |
Open-collector output, 100 mA max. |
Control Residual voltage output |
2 V max. (Load current: 100 mA, Cable length: 2 m) |
Indicators | NO Models: Operation indicator (yellow) (flashing), Setting indicator (yellow) (lit); NC Models: Operation indicator (yellow) (lit) |
Operation mode | B1/C1 Models: NO B2/C2 Models: NC (Refer to the timing charts under I/O Circuit Diagrams for details.) |
Protection circuits | Power supply reverse polarity protection, reversed output polarity protection, load short-circuit protection, surge suppressor |
Ambient temperature | Operating/Storage: -25 to 70°C (with no icing or condensation) |
Ambient humidity | Operating/Storage: 35% to 95% (with no condensation) |
Temperature influence |
Based on the sensing distance at 23°C in the temperature range of −25 to 70°C |
±10% max. | |
Voltage influence | ±1.5% max. of sensing distance at rated voltage in the rated voltage ±15% range |
Insulation resistance | 50 MW min. (at 500 VDC) between current-carrying parts and case |
Dielectric strength | 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case |
Vibration resistance | Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions |
Shock resistance | Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions |
Degree of protection | IEC IP67 (Pre-wired Models and Pre-wired Connector Models are oil-resistant to the OMRON in-house standard.) |
Connection method | Pre-wired Models (Standard cable length: 2 m), Connector Models, Pre-wired Connector Models (Standard cable length: 300 mm) |
Weight (packed state) Cable | Approx. 120 g |
Weight (packed state) Connector | Approx. 30 g |
Weight (packed state) Pre-wired Connector Models | Approx. 50 g |
Material Case | Nickel-plated brass |
Material sensing surface | Heat-resistant ABS |
Material Clamping nuts | Nickel-plated brass |
Material Toothed whasher | Zinc-plated iron |
Accessories | Instruction manual |
Item/ Model | E2V-X4 - - |
Size | M12 |
Sensing distance | 4mm±10% |
Set distance | 0 to 3.2 mm |
Differential travel | 10% max. of sensing distance |
Detectable object | Ferrous metals and non-ferrous metals (The sensing distance depends on the material of the sensing object. Refer to Engineering Data (Typical).) |
Standard sensing object | Aluminum: 12 × 12 × 3 mm |
Response frequency* | 40Hz |
Power supply voltage (operating voltage range) |
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. |
Current consumption | 450 mW max. (Current consumption: 15 mA max. at power supply voltage of 30 V) |
Control output Load current |
Open-collector output, 100 mA max. |
Control Residual voltage output |
2 V max. (Load current: 100 mA, Cable length: 2 m) |
Indicators | NO Models: Operation indicator (yellow) (flashing), Setting indicator (yellow) (lit); NC Models: Operation indicator (yellow) (lit) |
Operation mode | B1/C1 Models: NO B2/C2 Models: NC (Refer to the timing charts under I/O Circuit Diagrams for details.) |
Protection circuits | Power supply reverse polarity protection, reversed output polarity protection, load short-circuit protection, surge suppressor |
Ambient temperature | Operating/Storage: -25 to 70°C (with no icing or condensation) |
Ambient humidity | Operating/Storage: 35% to 95% (with no condensation) |
Temperature influence |
Based on the sensing distance at 23°C in the temperature range of −25 to 70°C |
±15% max. | |
Voltage influence | ±1.5% max. of sensing distance at rated voltage in the rated voltage ±15% range |
Insulation resistance | 50 MW min. (at 500 VDC) between current-carrying parts and case |
Dielectric strength | 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case |
Vibration resistance | Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions |
Shock resistance | Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions |
Degree of protection | IEC IP67 (Pre-wired Models and Pre-wired Connector Models are oil-resistant to the OMRON in-house standard.) |
Connection method | Pre-wired Models (Standard cable length: 2 m), Connector Models, Pre-wired Connector Models (Standard cable length: 300 mm) |
Weight (packed state) Cable | Approx. 120 g |
Weight (packed state) Connector | Approx. 30 g |
Weight (packed state) Pre-wired Connector Models | Approx. 50 g |
Material Case | Nickel-plated brass |
Material sensing surface | Heat-resistant ABS |
Material Clamping nuts | Nickel-plated brass |
Material Toothed whasher | Zinc-plated iron |
Accessories | Instruction manual |
Item/ Model | E2V-X5 - - |
Size | M18 |
Sensing distance | 5mm±10% |
Set distance | 0 to 4.0 mm |
Differential travel | 10% max. of sensing distance |
Detectable object | Ferrous metals and non-ferrous metals (The sensing distance depends on the material of the sensing object. Refer to Engineering Data (Typical).) |
Standard sensing object | Aluminum: 18 × 18 × 3 mm |
Response frequency* | 70Hz |
Power supply voltage (operating voltage range) |
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. |
Current consumption | 450 mW max. (Current consumption: 15 mA max. at power supply voltage of 30 V) |
Control output Load current |
Open-collector output, 100 mA max. |
Control Residual voltage output |
2 V max. (Load current: 100 mA, Cable length: 2 m) |
Indicators | NO Models: Operation indicator (yellow) (flashing), Setting indicator (yellow) (lit); NC Models: Operation indicator (yellow) (lit) |
Operation mode | B1/C1 Models: NO B2/C2 Models: NC (Refer to the timing charts under I/O Circuit Diagrams for details.) |
Protection circuits | Power supply reverse polarity protection, reversed output polarity protection, load short-circuit protection, surge suppressor |
Ambient temperature | Operating/Storage: -25 to 70°C (with no icing or condensation) |
Ambient humidity | Operating/Storage: 35% to 95% (with no condensation) |
Temperature influence |
Based on the sensing distance at 23°C in the temperature range of −25 to 70°C |
±10% max. | |
Voltage influence | ±1.5% max. of sensing distance at rated voltage in the rated voltage ±15% range |
Insulation resistance | 50 MW min. (at 500 VDC) between current-carrying parts and case |
Dielectric strength | 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case |
Vibration resistance | Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions |
Shock resistance | Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions |
Degree of protection | IEC IP67 (Pre-wired Models and Pre-wired Connector Models are oil-resistant to the OMRON in-house standard.) |
Connection method | Pre-wired Models (Standard cable length: 2 m), Connector Models, Pre-wired Connector Models (Standard cable length: 300 mm) |
Weight (packed state) Cable | Approx. 150 g |
Weight (packed state) Connector | Approx. 45 g |
Weight (packed state) Pre-wired Connector Models | Approx. 70 g |
Material Case | Nickel-plated brass |
Material sensing surface | Heat-resistant ABS |
Material Clamping nuts | Nickel-plated brass |
Material Toothed whasher | Zinc-plated iron |
Accessories | Instruction manual |
Item/ Model | E2V-X8 - - |
Size | M18 |
Sensing distance | 8mm±10% |
Set distance | 0 to 6.4 mm |
Differential travel | 10% max. of sensing distance |
Detectable object | Ferrous metals and non-ferrous metals (The sensing distance depends on the material of the sensing object. Refer to Engineering Data (Typical).) |
Standard sensing object | Aluminum: 24 × 24 × 3 mm |
Response frequency* | 40Hz |
Power supply voltage (operating voltage range) |
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. |
Current consumption | 450 mW max. (Current consumption: 15 mA max. at power supply voltage of 30 V) |
Control output Load current |
Open-collector output, 100 mA max. |
Control Residual voltage output |
2 V max. (Load current: 100 mA, Cable length: 2 m) |
Indicators | NO Models: Operation indicator (yellow) (flashing), Setting indicator (yellow) (lit); NC Models: Operation indicator (yellow) (lit) |
Operation mode | B1/C1 Models: NO B2/C2 Models: NC (Refer to the timing charts under I/O Circuit Diagrams for details.) |
Protection circuits | Power supply reverse polarity protection, reversed output polarity protection, load short-circuit protection, surge suppressor |
Ambient temperature | Operating/Storage: -25 to 70°C (with no icing or condensation) |
Ambient humidity | Operating/Storage: 35% to 95% (with no condensation) |
Temperature influence |
Based on the sensing distance at 23°C in the temperature range of −25 to 70°C |
±15% max. | |
Voltage influence | ±1.5% max. of sensing distance at rated voltage in the rated voltage ±15% range |
Insulation resistance | 50 MW min. (at 500 VDC) between current-carrying parts and case |
Dielectric strength | 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case |
Vibration resistance | Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions |
Shock resistance | Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions |
Degree of protection | IEC IP67 (Pre-wired Models and Pre-wired Connector Models are oil-resistant to the OMRON in-house standard.) |
Connection method | Pre-wired Models (Standard cable length: 2 m), Connector Models, Pre-wired Connector Models (Standard cable length: 300 mm) |
Weight (packed state) Cable | Approx. 150 g |
Weight (packed state) Connector | Approx. 45 g |
Weight (packed state) Pre-wired Connector Models | Approx. 70 g |
Material Case | Nickel-plated brass |
Material sensing surface | Heat-resistant ABS |
Material Clamping nuts | Nickel-plated brass |
Material Toothed whasher | Zinc-plated iron |
Accessories | Instruction manual |
Item/ Model | E2V-X10 - - |
Size | M30 |
Sensing distance | 10mm±10% |
Set distance | 0 to 8.0 mm |
Differential travel | 10% max. of sensing distance |
Detectable object | Ferrous metals and non-ferrous metals (The sensing distance depends on the material of the sensing object. Refer to Engineering Data (Typical).) |
Standard sensing object | Aluminum: 30 × 30 × 3 mm |
Response frequency* | 70Hz |
Power supply voltage (operating voltage range) |
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. |
Current consumption | 450 mW max. (Current consumption: 15 mA max. at power supply voltage of 30 V) |
Control output Load current |
Open-collector output, 100 mA max. |
Control Residual voltage output |
2 V max. (Load current: 100 mA, Cable length: 2 m) |
Indicators | NO Models: Operation indicator (yellow) (flashing), Setting indicator (yellow) (lit); NC Models: Operation indicator (yellow) (lit) |
Operation mode | B1/C1 Models: NO B2/C2 Models: NC (Refer to the timing charts under I/O Circuit Diagrams for details.) |
Protection circuits | Power supply reverse polarity protection, reversed output polarity protection, load short-circuit protection, surge suppressor |
Ambient temperature | Operating/Storage: -25 to 70°C (with no icing or condensation) |
Ambient humidity | Operating/Storage: 35% to 95% (with no condensation) |
Temperature influence |
Based on the sensing distance at 23°C in the temperature range of −25 to 70°C |
±10% max. | |
Voltage influence | ±1.5% max. of sensing distance at rated voltage in the rated voltage ±15% range |
Insulation resistance | 50 MW min. (at 500 VDC) between current-carrying parts and case |
Dielectric strength | 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case |
Vibration resistance | Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions |
Shock resistance | Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions |
Degree of protection | IEC IP67 (Pre-wired Models and Pre-wired Connector Models are oil-resistant to the OMRON in-house standard.) |
Connection method | Pre-wired Models (Standard cable length: 2 m), Connector Models, Pre-wired Connector Models (Standard cable length: 300 mm) |
Weight (packed state) Cable | Approx. 200 g |
Weight (packed state) Connector | Approx. 120 g |
Weight (packed state) Pre-wired Connector Models | Approx. 140 g |
Material Case | Nickel-plated brass |
Material sensing surface | Heat-resistant ABS |
Material Clamping nuts | Nickel-plated brass |
Material Toothed whasher | Zinc-plated iron |
Accessories | Instruction manual |
Item/ Model | E2V-X15 - - |
Size | M30 |
Sensing distance | 15mm±10% |
Set distance | 0 to 12.0 mm |
Differential travel | 10% max. of sensing distance |
Detectable object | Ferrous metals and non-ferrous metals (The sensing distance depends on the material of the sensing object. Refer to Engineering Data (Typical).) |
Standard sensing object | Aluminum: 45 × 45 × 3 mm |
Response frequency* | 30Hz |
Power supply voltage (operating voltage range) |
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. |
Current consumption | 450 mW max. (Current consumption: 15 mA max. at power supply voltage of 30 V) |
Control output Load current |
Open-collector output, 100 mA max. |
Control Residual voltage output |
2 V max. (Load current: 100 mA, Cable length: 2 m) |
Indicators | NO Models: Operation indicator (yellow) (flashing), Setting indicator (yellow) (lit); NC Models: Operation indicator (yellow) (lit) |
Operation mode | B1/C1 Models: NO B2/C2 Models: NC (Refer to the timing charts under I/O Circuit Diagrams for details.) |
Protection circuits | Power supply reverse polarity protection, reversed output polarity protection, load short-circuit protection, surge suppressor |
Ambient temperature | Operating/Storage: -25 to 70°C (with no icing or condensation) |
Ambient humidity | Operating/Storage: 35% to 95% (with no condensation) |
Temperature influence |
Based on the sensing distance at 23°C in the temperature range of −25 to 70°C |
±15% max. | |
Voltage influence | ±1.5% max. of sensing distance at rated voltage in the rated voltage ±15% range |
Insulation resistance | 50 MW min. (at 500 VDC) between current-carrying parts and case |
Dielectric strength | 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case |
Vibration resistance | Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions |
Shock resistance | Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions |
Degree of protection | IEC IP67 (Pre-wired Models and Pre-wired Connector Models are oil-resistant to the OMRON in-house standard.) |
Connection method | Pre-wired Models (Standard cable length: 2 m), Connector Models, Pre-wired Connector Models (Standard cable length: 300 mm) |
Weight (packed state) Cable | Approx. 200 g |
Weight (packed state) Connector | Approx. 120 g |
Weight (packed state) Pre-wired Connector Models | Approx. 140 g |
Material Case | Nickel-plated brass |
Material sensing surface | Heat-resistant ABS |
Material Clamping nuts | Nickel-plated brass |
Material Toothed whasher | Zinc-plated iron |
Accessories | Instruction manual |