Electro-Sensors, Inc. Speed Switches - Zero Speed, Under-Speed, Over-Speed, Relay Output, 4-20 mA Output
M100T / M5000T
Electro-Sensors Speed sensor and speed switch for detecting shaft slowdown, SPDT output relay, housed in a cast aluminum explosion proof enclosure.
FB420
SPDT output relay and 4-20 mA output speed sensor and speed switch, housed in a explosion proof and NEMA 4X enclosure. Relay can be set for overspeed or underspeed. 24 VDC.
DR1000
Shaft speed switch with DPDT output relay to detect shaft slowdown or stoppage. The DR1000 is housed in an explosion proof and waterproof cast aluminum enclosure.
LRB1000 / LRB2000
Speed Switch with one or two adjustable SPDT setpoint relays to detect over-speed, under-speed, or stoppage. Built-in start delay and signal loss protection. Housed in a NEMA 1 enclosure.
SCP1000 / SCP2000
Self-contained, presettable sensor and speed switch with one or two adjustable SPDT or DPDT setpoint relays to detect over-speed or under-speed. Built-in start delay. Housed in a cast aluminum explosion proof enclosure.
UDS1000
Reverse shaft rotation detector with DPDT output relay. Automatically resets when reverse motion stops. Housed in a cast aluminum explosion proof enclosure.
SS110
One adjustable SPDT output relay for detecting shaft speed in super slow speed applications. Built-in start delay. Housed in a NEMA 1 enclosure.
PVC100/5000
The PVC100 is a smaller speed switch with a PVC housing. This switch is optimal for applications with cramped spaces and no Explosion-Proof requirement.
SPEEDTALKER-DN(UI)
Universal-Input Shaft Speed measurement with alarms (Shaft Speed Switch) and DeviceNet network interface
OEM SWITCH DMS100/5000
The DMS speed switch is an economical choice housed in a compact plastic enclosure, it mounts on a standard 35 mm DIN rail and operates on 115/230 VAC with optional DC units available.
M100/5000 (FOR REPLACEMENT PURPOSES ONLY)
Self-contained sensor and speed switch for detecting shaft slowdown, SPDT relay output, housed in an explosion proof cast aluminum or a corrosion-resistant PVC enclosure.
MOTRONA CONTROL
Control products include: electronic counters for frequencies up to 1 MHz; tachometers & frequency meters; process indicators & panel meters with analog input; SSI displays (dual position & sum/differential); monitors for speed, standstill, slip, shaft fracture, skew position etc. Units available with optional outputs & interfaces.
AX020
Small panel meter for standard analog signals
AX320 - AX321 - AX322 - AX323
Process indicators with analog input for standard signals and strain gauge
AX350
Process indicator with two 16 bit analog inputs.
BG230/250
program unit for the ds230/350
DS230 - DS236 - BG230
Safety Motion Monitors for SinCos and Incremental Encoders / Sensors
DS240 - DS246 - BG230
SIL3/PLe certified Safety Motion Monitor for Speed, Standstill and Direction of rotation (for connection of a SIL3/PLe certified SinCos encoder or sensor)
DS 250/260
Safety speed monitor for incremental encoders / sensors
DX020
Small tachometer and frequency meter
DZ210
Monitor for direction of rotation and standstill
DZ260 - DZ266 - DZ267
Monitor for speed, direction of rotation and standstill
DZ 261
Speed Monitor with 3 Transistor Outputs and Analog Output
DZ269
Speed Monitor with 3 Output Relays
DZ270 - DZ271 - DZ276 - DZ277 - DZ279
Universal Monitors for Speed, Standstill, Direction of Rotation
ID / IA / IR 330-644
Dual position and differential indicators for use with two encoders or measuring systems(SSI absolute or incremental)
IX350/355
IX350/355 SSi indicator for absolute encoders.
MM 640
Programmable Motion Monitor for Secure and Redundant Control of Motion Sequences.
MS640
Motion monitor for secure control
PB306 - CA306
Simple preset units for PROFIBUS and CANBUS
PB340 - CA340
PROFIBUS and CANBUS Indicator Units
PB541 - CA541
Combination of preset and display unit
SA / AD / SR 330
Advanced measurement of rpm, speeds, speed ratios, sum, differential speeds or baking and processing times
SD / SA / SR 340-644
Advanced measurement of rpm, speeds, baking and processing times, speed ratios, sum or differential speeds
ZD / ZA / ZR 330-644
High speed position counters and differential counters with two encoder inputs
ZX020
Small-sized position indicator and event counter
ZX122 - ZX123
Multi-function tachometer
SHAFT SPEED SENSORS
Hall-Effect & Magnetoresistive Speed Sensors, Speed Output, Shaft Speed Detection, Explosion-Proof (XP), Digital Magnetic Speed Sensor
907 XP HALL EFFECT
Hall Effect digital speed sensors powered by 5-24 VDC, provide NPN open collector output, have a 1-inch NPT conduit port, and are compatible with a PLC digital I/O. 907 XP (Explosion Proof) sensors are used in applications requiring hazardous location ratings, or in applications where the sensor may be subject to abuse. Bi-Directional models are available (907B XP)
906 HALL EFFECT
Hall Effect digital speed sensors powered by 5-24 VDC, provide NPN open collector output, compatible with a PLC digital I/O. Aluminum, Stainless Steel, and PVC body types, high-temperature cable, and Quadrature options.
SERIES 18
Hall Effect and Magnetoresistive sensors, single channel or bi-directional signaling, NPN and PNP transistor outputs, available with four housing options. FM Approved Intrinsically Safe
ST420-LT / ST420-DI
The ST420-LT and ST420-DI are 2-wire, loop-powered, 4-20 mA analog output shaft speed sensors in rugged stainless steel M18x1 housings with integral conduit attachments; FM Approved Dust-Ignition-Proof for Class II Division I hazardous locations.
ST420
The ST420 is a 2-wire, loop-powered, 4-20 mA analog output shaft speed sensor in a rugged stainless steel M18x1 housing; UL Listed Intrinsically Safe (IS) for Class I Division I and Class II Division I hazardous locations.
1101 HALL EFFECT SENSOR
The stainless steel Hall Effect sensor provides a square-wave pulse frequency output, NPN open-collector. It is 5-24 VDC powered with zero speed operation and no signal loss. These Hall Effect sensors work with Electro-Sensors Pulser Discs and Split Collar Pulser Wraps.
1102 / 932 / 933 XP
Magnetoresistive speed sensors powered by 5-24 VDC with an NPN open collector output. Stainless steel, aluminum, and explosion proof models.
600 SERIES PROXIMITY
Proximity sensors are active digital sensing devices with full NPN output signal down to zero Hz. Outputs are CMOS compatible. Available in a wide range of voltages. Metal housing is corrosion-resistant.
HE950
Gear tooth sensor powered by 5-24 VDC, provides an NPN open collector digital output signal. Senses frequency range up to 12 kHz. Threaded aluminum, NEMA 4 housing.
931 XP HALL EFFECT
The explosion proof 931 XP Hall Effect sensor provides a square-wave pulse frequency output, NPN open-collector. It is 5-24 VDC powered with zero speed operation and no signal loss. The differentiating features between the 931 XP and the 907 XP are that the 931 XP has slightly smaller body and 1/2 inch NPT conduit port. These Hall Effect sensors work with Electro-Sensors Pulser Discs and Split Collar Pulser Wraps.
SPEEDTALKER-DN(BH) DEVICENET
Shaft Speed Sensor with Alarms (Shaft Speed Switch) and DeviceNet network interface
SPEEDTALKER-DN(XP) DEVICENET
Shaft Speed Sensor with Alarms (Shaft Speed Switch) and DeviceNet network interface
916A / 917A (REPLACEMENT ONLY)
Model 916A and 917A Passive Analog Sensors are designed for use with pulse generators that provide magnetic targets, such as Pulser Discs and Split Collar Pulser Wraps.
SHAFT SPEED PULSE GENERATORS
Shaft Speed Pulse Generators provide the targets needed for shaft speed detection with a sensor or switch.
PULSER DISCS
End of shaft mounting, non-contact sensing, material options include nylon, aluminum, PVC, and stainless steel. Magnets can be face or edge read and can produce a customized number of pulses, 10,000 rpm maximum speed.
SPLIT COLLAR PULSER WRAPS
Clamps tightly to the shaft when end-of-shaft mounting is inaccessible. Material options include PVC, aluminum, and stainless steel. Magnets are mounted on the the outside circumference. Pulses per revolution can be customized.
DIGITAL RING KITS
Kit includes NEMA C mounting ring, hardware magnet wheel and sensor. Available with single or bi-directional output, 60 or 120 pulses per revolution, NPN open collector output.
ENCODERS
Rotary shaft encoders for use on slow shaft speed applications. High resolution digital pulse output and heavy-duty models. NPN open collector output or two square waves in bi-directional.
EZ-3/4IN & EZ-18MM
The EZ-18mm and the EZ-3/4in Easy Mount Bracket Assemblies are used with Electro-Sensors speed sensors to generate pulses or 4-20 mA signals for use with display meters, speed switches, or PLC inputs. Pulser Disc included.
EZ-100 & EZ-SCP
Simplifies mounting, installation, and operation with certain models of shaft speed switches and sensors.
MAGNET WHEELS
Comprise a ferro-magnetic nylon ring with 120 alternating magnetic poles and an aluminum hub.
TRACTION WHEELS
Converts linear travel to a digital pulse frequency, NPN open collector output, ideal for slow speed applications. Includes traction wheel, encoder, and mounting bracket with mating connector. Bi-directional models available.
MOTRONA MOTION
Motion products include: synchronous controllers for electrical drives; controllers for rotation cutters & rotary shear systems; controllers for machining “on the fly” (flying shears, saws, punchers, cutters etc.); special controllers for tubular bag machines (packing) or intermitting printing machines (label printing) & many other sophisticated applications.
BY340
Synchronous controller for one follower axis
BY641
Synchronous controller for one follower axis
BY701 FIRMWARE (FOR MC700/MC720 CONTROLLER)
With use of BY701 firmware, the MC700 controller provides excellent solutions with all kinds of multi-axes synchronizing applications. Numerous possibilities for control of relative phase, position, index and print mark evaluation are available.
CT340-CT641
Compact and Low Priced Motion Controller for Rotation Machining, Rotating Cross Cutters, Rotary Punchers, and Other Intermittent Operations
CT701 FIRMWARE (FOR MC700/MC720 CONTROLLER)
With use of CT701 firmware, the MC700 controller provides excellent solutions with all kinds of guillotine cutters and rotary eccentric shears needing a cosine-compensated speed profile during the penetration of the tool.
CT703 FIRMWARE (FOR MC700/MC720 CONTROLLER)
With use of the CT703 firmware, the MC700 controller provides excellent solutions with all kinds of rotating cut-to-length systems as well as with applications like rotary labeling, printing, punching, sealing etc.
FS340-FS641
Compact and Low-Priced Motion Controller for Machining “On The Fly” like Flying Shears, Saws, Punchers, and Cutters
FS701 FIRMWARE (FOR MC700/MC720 CONTROLLER)
With use of FS701 firmware, the MC700 controller provides excellent solutions with all kinds of flying cut-to-length systems as well as with applications like labeling, printing, punching, sealing etc.
MC700 / MC720 UNIVERSAL MOTION CONTROLLER
Universal motion controllers for up to 4 axes, with multiple possibilities and applications with drive systems
MC800 UNIVERSAL MOTION CONTROLLER
MC800 Universal Motion Controller for Two Axes
TB701 FIRMWARE (FOR MC700/MC720 CONTROLLER)
WR701 FIRMWARE (FOR MC700/MC720 CONTROLLER)
This winding application firmware provides full control of up to 4 drives, with 16 different possibilities of combinations for, winding, unwinding, tension control, and traverse control. For use with MC700/MC720.
MB800
Interface module for Motrona MC800 motion controller.
WIRELESS HAZARD MONITORING
HazardPRO Wireless Hazard Monitoring System, Wireless Temperature Sensors, Ambient Temperature Compensation, Wireless Shaft Speed Sensor, process control
HAZARDPRO™ SYSTEM
The turn-key HazardPRO wireless hazard monitoring system combines rugged sensors, intuitive software, and the most advanced wireless technology to create the best hazard monitoring solution with the lowest installed cost.
HAZARDPRO™ RPM SENSOR
HazardPRO shaft RPM sensors connect directly to the HazardPRO transmitter node as an integral part of the hazard monitoring system.
HAZARDPRO™ BEARING SENSOR
HazardPRO bearing temperature sensors connect directly to the HazardPRO transmitter node as an integral part of the hazard monitoring system.
HAZARDPRO™ VIBRATION SENSOR
The HazardPRO vibration velocity sensor or VTHP is an RMS sensor (per ISO 10816) that measures and checks for unwanted equipment vibration and works with HazardPRO systems.
HAZARDPRO™ BELT ALIGNMENT
HazardPRO belt alignment temperature sensors connect directly to the HazardPRO transmitter node as an integral part of the hazard monitoring system.
HAZARDPRO™ AMBIENT
HazardPRO ambient temperature sensors connect directly to the HazardPRO transmitter node as an integral part of the hazard monitoring system.
HAZARDPRO™ STUD SENSOR
HazardPRO stud-mount temperature sensors connect directly to the HazardPRO transmitter node as an integral part of the hazard monitoring system.
HAZARDPRO™ NODE
The battery-powered I.S. HazardPRO Node is the sensor-input building block for HazardPRO Hazard Monitor Systems, providing intrinsically safe connections for 10 compatible sensors. Nodes power their sensors, acquire their signals and transmit to the HazardPRO System Manager via wireless network.
HAZARDPRO™ SYSTEM MANAGERS XS/XM/XL
HazardPRO Wireless Hazard Monitoring System consists of three different system sizes. Wireless monitoring is the new direction for hazard monitoring systems offering more benefits than traditional systems.
MOTRONA INTERFACE
Interface products include: level converters, splitters, distributors, switchers for incremental or SinCos encoder signals; signal converters & conditioners for frequencies, analog signals, SSI or SinCos encoders, parallel & serial measuring data; frequency dividers & frequency multipliers; innovative optical fiber modules.
CA307
The CA307 data preset unit with CANopen interface
CI800
Interface for motrona MC800 motion controller
FM260
Impulse and frequency multiplier
FU210 SIGNAL CONVERTER
The FU210 signal converter processes input signals as frequency or velocity information.
FU252
Converter frequency - analog/serial
DX350/355 TOUCHMATRIX
The DX350/355 TouchMATRIX are Tachometer display units with programmable color coded set points.
GI210
Changeover switch for two SSI encoders and one target unit
GS202
2 x 6 control outputs für HTL / PNP signals
GV 155/156
Electronic cross switchers for encoder signals and analogue signals
GV204
Impulse Splitter for Incremental Encoders
GV210
Dual encoder splitter and switcher
GV460/461 - GV470/471 - GV480/481
Signal distributor with 4 or 8 output channels
IP251
Converter SSI/RS232 - parallel
IT210
The IT210 is a universal interface using with incremental measuring systems with diverse functions, such as: Level conversion (RS422, HTL single ended, HTL differential, TTL and vice versa), Division of two-track A / B pulses with adjustable ratio 1: 1 to 1: 2048, Division of the Z pulse with adjustable ratio 1: 1 to 1: 256, External HTL signals for various functions, Implementation between the two types of representations for the direction of rotation (A/B 90 °, A/B Dir and vice versa, Division possible)
IT251
Programmable frequency divider
IV251
Converter SSI - analog/serial
IV210
With its SSI interface, the IV210 converts absolute position values into high-precision current or voltage value.
LW 213/214
Optical fiber modules for transmission of incremental encoder or sensor signals
PU202
Level converter HTL to TTL-RS422 (no potential separation)
PU204
Level converter TTL-RS422 to HTL (no potential separation)
PU210
Universal level converter TTL/RS422 HTL
SI251
SINE/COSINE interpolator
SV210
Signal distributor/splitter for SINE-COSINE encoder
SV211
4-Way Signal Distributor / Splitter for Sine-Cosine Encoder Signals
UZ210
Converter analog - incremental impulses/frequency/SSI
ZU210
The ZU210 converts counting pulses or position values up to 1 MHz almost instantaneously into analog or serial signals. Possible input formats are TTL / RS422, HTL differential, HTL PNP and HTL NPN. The converted signals are then available with a resolution of 16 bits or as digital information via Modbus RTU for further processing.
ZU252
Incremental count - analog/serial
MOTRONA ACCESSORIES
Accessories include operator terminals, cables, universal power units, mounting brackets, replacement circuit boards, splitters & housings.
BT348
Low cost Operator Terminal with Serial Interface
ES001
Incremental encoder simulator
FK470
Assembled cables
NT215
Universal power unit 24 Vdc/15 W
PB251
PROFIBUS-Gateway
RL203
Relay PCB with two standard relays
RL204
Relay PCB with two safety relays (forced guided contacts)
RV210
Splitter for serial communication
SK232
Assembled Cables
SM300 - SM600
Mounting clamps and brackets
TG300
Desktop housing
CK 232
USB to RS232 converter (compatible to all existing Windows versions)
WIRED HAZARD MONITORING
Electro-Sensors Wired Hazard Monitoring Systems give the facility insight into their equipment by catching equipment failure before it starts. Fully approved Explosion-Proof Systems.
ELECTRO-SENTRY 1
Single-leg or conveyor Hazard Monitoring System for monitoring shaft speed, bearing temperature, and belt alignment. All sensors have their value and alarm status displayed on the front panel.
ELECTRO-SENTRY 16
A Hazard Monitoring System that contains at-a-glance Temperature monitoring with alarm identification for up to sixteen 4-20 mA analog Temperature or Contact Closure sensors.
ION REMOTE I/O
Sensor-input and relay-output modules with Modbus RTU network interface. 3 Models: Analog-In (12 inputs), Discrete I/O (6 inputs, 6 relay outputs) and Frequency/Discrete-In (12 inputs) All provide protected sensor power. All signal inputs are protected.
TEMPERATURE SENSORS
Electro-Sensors Temperature Sensors can be used to Monitor Temperature on a Wide Range of Industrial Machinery.
TT420
TT420 Temperature Sensors, UL Listed Temperature Sensors, Intrinsically Safe (I.S.), Industrial Temperature Measurement Applications.
TT420-LT
TT420-LT Dust-Ignition-Proof Temperature Sensors, 4-20 mA Output, Intrinsically Safe, Liquid Tight
RTD / RTD-LT
RTDZ, RTDZ-LT, RTDS and RTDS-LT are resistance-output Pt100 RTD temperature sensors with 3-wire cable
SLIDE GATE & ANGLE POSITION
Measure a Wide Range of Shaft Angle and Linear Position on Slide Gates and Valves Using the SG1000 position monitor.
SG1000B
The SG1000B slide gate monitor provides accurate gate position feedback when measuring linear position where the end-to-end linear movement can be tracked via a telescopic-arm, which converts the linear position to an angular movement. Provides 4-20 mA output and interfaces with optional PM500 Process Meter as a remote display unit or a PLC. Housed in an explosion proof, NEMA 4X enclosure.
SG1000C
The SG1000C single-turn position monitor provides accurate shaft position feedback where the end-to-end rotation is exactly 360 degrees before reversing, or when the process just repeats itself after turning 360 degrees without reversing. Provides 4-20 mA output and interfaces with optional PM500 Process Meter as a remote display unit or a PLC. Housed in an explosion proof, NEMA 4X enclosure.
SG1000D
The SG1000D valve position monitor provides accurate valve position feedback where the end-to-end rotation is anywhere between 0 and 360 degrees before reversing. Provides 4-20 mA output and interfaces with optional PM500 Process Meter as a remote display unit or a PLC. Housed in an explosion-proof, NEMA 4X enclosure.
SG1000E
Provides accurate shaft position feedback where the end-to-end rotation is anywhere between 0 and 130 degrees before reversing. Provides 4-20 mA output and interfaces with optional PM500 Process Meter as a remote display unit or a PLC. Housed in an explosion proof, NEMA 4X enclosure.
SG1000F
Provides accurate shaft position, slide gate, and valve position feedback where the end-to-end rotation is a full span anywhere between a 1/12th of a turn up to two full turns before reversing. Provides 4-20 mA output and interfaces with optional PM500 Process Meter as a remote display unit or a PLC. Housed in an explosion-proof, NEMA 4X enclosure.
SG1000RA
An accurate and reliable slide gate or valve end-point position monitor with a 2-Relay output. Powered by 115 - 230VAC ±10% with the ability to control equipment, horns, lights, or other facility alarm systems. Housed in an explosion-proof, NEMA 4X enclosure and comes with UL Class I, Div. I (C, D) and Class II, Div. I (E, F, G) approvals.
PM500
The PM500 is a fully programmable process meter with two 4-20 mA sensor inputs that can be scaled to any user-selected units. It can easily display any production variable such as temperature, position, or rate.The ability to detect, convert, and display the input signal makes the PM500 an inexpensive solution to many industrial applications.
BEARING SENSORS & BELT ALIGNMENT
Electro-Sensors Bearing and Belt Alignment Sensors Provide Early Warning of Overheating.
TT420
TT420 Temperature Sensors, UL Listed Temperature Sensors, Intrinsically Safe (I.S.), Industrial Temperature Measurement Applications.
TT420-LT
TT420-LT Dust-Ignition-Proof Temperature Sensors, 4-20 mA Output, Intrinsically Safe, Liquid Tight
RTD / RTD-LT
RTDZ, RTDZ-LT, RTDS and RTDS-LT are resistance-output Pt100 RTD temperature sensors with 3-wire cable
RUB BLOCK DOOR ASSEMBLIES
Rub block door assemblies available in standard hinged, adjustable, and Uni-Strut models. Provides early warning of conveyor or elevator belt misalignment. Allows for easy installation and access.
MODEL TA
Conveyor belt misalignment system comes with one or two SPDT limit switches rated for 20 A at 120 VAC, 250 VAC, and 480 VAC. 3/4 inch NPT conduit opening on all units. Cast aluminum or cast iron units available.
MODEL DB
The Model DB is a damaged belt detector that is typically installed on both sides of a conveyor. (Sold in Pairs) It detects Rips, Tears, protrusions, and sagging to prevent further damage to the belt and reduce damage costs.
MODEL PC
The Model PC is a Safety Stop switch commonly used with conveyors. They provide facilities and personnel with a way to provide positive shut-down to equipment.
MODEL RS
The Model RS is a Safety Stop switch Commonly used with conveyors. They provide facilities and personnel with a way to provide positive shut-down to equipment.
MODEL RSB
The Model RSB is a Safety Stop switch commonly used with conveyors. They provide facilities and personnel with a way to provide positive shut-down to equipment. The RSB has cord break detection to notify if a pull cord becomes severed.
TACHOMETERS, COUNTERS & DISPLAYS
Our Tachometers, Process Meters, and Counters Provide a Range of Display Options for Industrial Processes.
AP1000
Digital tachometer displays rates from 0-9,999 or time in process, field-programmable panel mount meter, optional voltages available.
TR5000
Full logic control ratemeter with three programmable transistor setpoint outputs and three programmable AC inputs. Monitors two shaft simultaneously and displays rate, time in process, ratio, sum, difference, or draw. Optional relay outputs and 4-20 mA output.
TR400
Speed and direction indicator, displays rate or time in process, single channel or bi-directional decoding, completely field-programmable. Optional relay outputs and 4-20 mA output.
PM500
The PM500 is a fully programmable process meter with two 4-20 mA sensor inputs that can be scaled to any user-selected units. It can easily display any production variable such as temperature, position, or rate.The ability to detect, convert, and display the input signal makes the PM500 an inexpensive solution to many industrial applications.
CT6000
Process counter with three programmable transistor setpoint outputs and three programmable AC inputs. Displays process, batch, total, and rate. Optional relay outputs and 4-20 mA output.
HH100
Hand-held contact or non-contact digital tachometer that measures rpm, surface speed, and length. Measures from 1-99,999 rpm, with accuracy of 0.02% with a resolution of 0.01 rpm.
SIGNAL CONDITIONERS & INTERFACE
SA420
Digital signal conditioner provides Analog signal directly proportional to the speed of a rotating shaft, and one selectable voltage signal.
ION REMOTE I/O
Sensor-input and relay-output modules with Modbus RTU network interface. 3 Models: Analog-In (12 inputs), Discrete I/O (6 inputs, 6 relay outputs) and Frequency/Discrete-In (12 inputs) All provide protected sensor power. All signal inputs are protected.
AIFO-200
Analog to frequency conversion module, 0-10 VDC and 4-20 mA inputs, 1-20 kHz output switch selectable. NPN open collector or driven output.
SPEEDTALKER-DN(UI)
Universal-Input Shaft Speed measurement with alarms (Shaft Speed Switch) and DeviceNet network interface
VIBRATION & TILT
Industrial Vibration Monitoring. Monitor machinery for vibration or lack of vibration.
VT420
The VT420 is an RMS vibration velocity sensor (per ISO 10816) with a 4-20mA output. Its primary function is to monitor and protect equipment against unwanted vibration. The VT420 acts as a preventive maintenance measure while communicating live sensor data to a PLC or an optional PM500 process meter remote display.
VS1/ VS2
Monitors vibration to protect industrial machinery against failure associated with vibration levels above or below the trip point. VS1 is optimized for non-intentionally vibrating machinery; VS2 for intentionally vibrating machinery. Two output options: SPDT relay or isolated transistor output (may be connected sourcing or sinking). Two housing options: compact NEMA 4X and Class I and II rated explosion proof (XP).
MTS SERIES & SCU-200
Tilt switch system consisting of a control unit and sensing probe used to sense the presence or absence of any bulk material. Control unit will interface with any tilt switch probes.
VUM800
Vibration monitor used to confirm normal operation of processes utilizing continuous vibration. DPDT 10 amp relay, optional 230 VAC operation.
ACCESSORIES
Easy Mounting and Protection Options for Speed Switches, Speed Sensors, and Pulser Discs.
DISC GUARDS
Rugged stainless steel disc guards to protect your sensor, switch, and disc.
ENCLOSURES
Explosion Proof Enclosures, NEMA 4 and NEMA 12 Steel Enclosure Kits, and NEMA 4X Fiber Glass Enclosure Kits for protecting speed switches, discs, tachometers, motor controllers, and counters in hazardous environments.
EZ MOUNTING MAGNETS
MM-1.25 and MM-2.00 EZ Mounting Magnets are used with the EZ-100 and EZ-SCP Mounting Brackets and are applied to the end of untapped shafts.
EZ-3/4IN & EZ-18MM
The EZ-18mm and the EZ-3/4in Easy Mount Bracket Assemblies are used with Electro-Sensors speed sensors to generate pulses or 4-20 mA signals for use with display meters, speed switches, or PLC inputs. Pulser Disc included.
EZ-100 & EZ-SCP
Simplifies mounting, installation, and operation with certain models of shaft speed switches and sensors.
MOTOR DRIVE CONTROL
Motor speed drive controllers ranging from simple speed display to complex process synchronizers.
ACCU-TACH & ACCU-DIAL
Motor speed control potentiometers with a programmable LCD display for the speed setting or measured shaft speed. The LCD displays four digits in user units. Accu-Tach works with pulse-frequency output shaft speed sensors and incremental shaft encoders.
MS320
Closed-loop motor speed drive control. Master and Ratio-Follower modes and programmable input functions. Options include analog speed feedback input, analog setpoint inputs and relay outputs. Works with incremental shaft encoders and pulse-frequency output shaft speed sensors.
MS332
Closed-loop synchronous motor speed drive control. Modes include zero-cumulative-error Ratio-Follower (electronic gearing) and zero-cumulative-error Index-Follower (mechanical event/phase synchronization). Features include Forward-only and Forward/Reverse settings for uni/bi-directional control, multiple setpoints and many programmable contact-closure input and NPN output functions. Builds numerous machine synchronizing/follower processes. Works with quadrature incremental shaft encoders (all modes) and prox, photo-eye and other presence/event sensors (Index-Follower mode).
MOTRONA - CONTROL / MOTION / INTERFACE
Electro-Sensors is a distributor of Motrona Automation Products in North America.
AX020
Small panel meter for standard analog signals
AX320 - AX321 - AX322 - AX323
Process indicators with analog input for standard signals and strain gauge
CA307
The CA307 data preset unit with CANopen interface
BY340
Synchronous controller for one follower axis
AX350
Process indicator with two 16 bit analog inputs.
CI800
Interface for motrona MC800 motion controller
BY641
Synchronous controller for one follower axis
BG230/250
program unit for the ds230/350
BY701 FIRMWARE (FOR MC700/MC720 CONTROLLER)
With use of BY701 firmware, the MC700 controller provides excellent solutions with all kinds of multi-axes synchronizing applications. Numerous possibilities for control of relative phase, position, index and print mark evaluation are available.
DS230 - DS236 - BG230
Safety Motion Monitors for SinCos and Incremental Encoders / Sensors
CT340-CT641
Compact and Low Priced Motion Controller for Rotation Machining, Rotating Cross Cutters, Rotary Punchers, and Other Intermittent Operations
DS240 - DS246 - BG230
SIL3/PLe certified Safety Motion Monitor for Speed, Standstill and Direction of rotation (for connection of a SIL3/PLe certified SinCos encoder or sensor)
FM260
Impulse and frequency multiplier
CT701 FIRMWARE (FOR MC700/MC720 CONTROLLER)
With use of CT701 firmware, the MC700 controller provides excellent solutions with all kinds of guillotine cutters and rotary eccentric shears needing a cosine-compensated speed profile during the penetration of the tool.
DS 250/260
Safety speed monitor for incremental encoders / sensors
FU210 SIGNAL CONVERTER
The FU210 signal converter processes input signals as frequency or velocity information.
CT703 FIRMWARE (FOR MC700/MC720 CONTROLLER)
With use of the CT703 firmware, the MC700 controller provides excellent solutions with all kinds of rotating cut-to-length systems as well as with applications like rotary labeling, printing, punching, sealing etc.
DX020
Small tachometer and frequency meter
FU252
Converter frequency - analog/serial
DX350/355 TOUCHMATRIX
The DX350/355 TouchMATRIX are Tachometer display units with programmable color coded set points.
FS340-FS641
Compact and Low-Priced Motion Controller for Machining “On The Fly” like Flying Shears, Saws, Punchers, and Cutters
GI210
Changeover switch for two SSI encoders and one target unit
DZ210
Monitor for direction of rotation and standstill
FS701 FIRMWARE (FOR MC700/MC720 CONTROLLER)
With use of FS701 firmware, the MC700 controller provides excellent solutions with all kinds of flying cut-to-length systems as well as with applications like labeling, printing, punching, sealing etc.
GS202
2 x 6 control outputs für HTL / PNP signals
DZ260 - DZ266 - DZ267
Monitor for speed, direction of rotation and standstill
MC700 / MC720 UNIVERSAL MOTION CONTROLLER
Universal motion controllers for up to 4 axes, with multiple possibilities and applications with drive systems
GV 155/156
Electronic cross switchers for encoder signals and analogue signals
MC800 UNIVERSAL MOTION CONTROLLER
MC800 Universal Motion Controller for Two Axes
GV204
Impulse Splitter for Incremental Encoders
DZ 261
Speed Monitor with 3 Transistor Outputs and Analog Output
TB701 FIRMWARE (FOR MC700/MC720 CONTROLLER)
GV210
Dual encoder splitter and switcher
DZ269
Speed Monitor with 3 Output Relays
DZ270 - DZ271 - DZ276 - DZ277 - DZ279
Universal Monitors for Speed, Standstill, Direction of Rotation
GV460/461 - GV470/471 - GV480/481
Signal distributor with 4 or 8 output channels
WR701 FIRMWARE (FOR MC700/MC720 CONTROLLER)
This winding application firmware provides full control of up to 4 drives, with 16 different possibilities of combinations for, winding, unwinding, tension control, and traverse control. For use with MC700/MC720.
ID / IA / IR 330-644
Dual position and differential indicators for use with two encoders or measuring systems(SSI absolute or incremental)
IP251
Converter SSI/RS232 - parallel
MB800
Interface module for Motrona MC800 motion controller.
IX350/355
IX350/355 SSi indicator for absolute encoders.
IT210
The IT210 is a universal interface using with incremental measuring systems with diverse functions, such as: Level conversion (RS422, HTL single ended, HTL differential, TTL and vice versa), Division of two-track A / B pulses with adjustable ratio 1: 1 to 1: 2048, Division of the Z pulse with adjustable ratio 1: 1 to 1: 256, External HTL signals for various functions, Implementation between the two types of representations for the direction of rotation (A/B 90 °, A/B Dir and vice versa, Division possible)
IT251
Programmable frequency divider
MM 640
Programmable Motion Monitor for Secure and Redundant Control of Motion Sequences.
IV251
Converter SSI - analog/serial
MS640
Motion monitor for secure control
BT348
Low cost Operator Terminal with Serial Interface
PB306 - CA306
Simple preset units for PROFIBUS and CANBUS
IV210
With its SSI interface, the IV210 converts absolute position values into high-precision current or voltage value.
PB340 - CA340
PROFIBUS and CANBUS Indicator Units
LW 213/214
Optical fiber modules for transmission of incremental encoder or sensor signals
PB541 - CA541
Combination of preset and display unit
FK470
Assembled cables
PR210
Converter parallel data - serial data
SA / AD / SR 330
Advanced measurement of rpm, speeds, speed ratios, sum, differential speeds or baking and processing times
NT215
Universal power unit 24 Vdc/15 W
PU202
Level converter HTL to TTL-RS422 (no potential separation)
SD / SA / SR 340-644
Advanced measurement of rpm, speeds, baking and processing times, speed ratios, sum or differential speeds
PB251
PROFIBUS-Gateway
PU204
Level converter TTL-RS422 to HTL (no potential separation)
ZD / ZA / ZR 330-644
High speed position counters and differential counters with two encoder inputs
PU210
Universal level converter TTL/RS422 HTL
RL203
Relay PCB with two standard relays
ZX020
Small-sized position indicator and event counter
RL204
Relay PCB with two safety relays (forced guided contacts)
SI251
SINE/COSINE interpolator
ZX122 - ZX123
Multi-function tachometer
RV210
Splitter for serial communication
SV210
Signal distributor/splitter for SINE-COSINE encoder
SK232
Assembled Cables
SV211
4-Way Signal Distributor / Splitter for Sine-Cosine Encoder Signals
SM300 - SM600
Mounting clamps and brackets
TG300
Desktop housing
UZ210
Converter analog - incremental impulses/frequency/SSI
CK 232
USB to RS232 converter (compatible to all existing Windows versions)
ZU210
The ZU210 converts counting pulses or position values up to 1 MHz almost instantaneously into analog or serial signals. Possible input formats are TTL / RS422, HTL differential, HTL PNP and HTL NPN. The converted signals are then available with a resolution of 16 bits or as digital information via Modbus RTU for further processing.
dienelectrics@gmail.com
0909186879 
