Bộ đếm Magnescale LT10A-205C

THÔNG TIN THAM KHẢO

• Danh mục Model sản phẩm MAGNESCALE

• 

  Trực quan về Ứng dụng Bộ đếm Counters trong trong nghiệp

• Xem thêm

Magnescale LT10A-205C là Bộ hiển thị-đếm 2-axis digital, DIN 72x72mm, màn hình 6-dig LCD, đèn nền, 5-10µm, RS-232C, 2 kênh (A+B, A-B, B-A), đầu ra Go/No-Go.

 

- Tài liệu kỹ thuật của Bộ đếm Magnescale LT10A-205C ở đây.

 

Tóm tắc về Bộ đếm Magnescale LT10A-205C

Magnescale LT10A-205C là bộ hiển thị và đếm kỹ thuật số 2 trục nhỏ gọn, được thiết kế để lắp trên bảng điều khiển (tiêu chuẩn DIN 72x72 mm). Thiết bị sở hữu màn hình LCD 6 chữ số có đèn nền, độ phân giải 5 µm hoặc 10 µm, hỗ trợ giao tiếp RS-232C, tính toán số học 2 kênh (A+B, A-B, B-A) và đầu ra so sánh đạt/không đạt (Go/No-Go).
 

Tóm tắc thông số kỹ thuật chung và vật lý của Bộ đếm Magnescale LT10A-205C

- Số trục: 2 kênh (hỗ trợ các thiết bị đo dòng DT12 hoặc DT32)
- Kích thước bảng điều khiển: DIN 72 × 72 mm
- Màn hình: LCD 6 chữ số có đèn nền, kèm các chỉ báo trạng thái hoạt động
- Trọng lượng: Khoảng 230 g
- Nhiệt độ hoạt động: 0 °C đến +40 °C
- Nhiệt độ bảo quản: -10 °C đến +50 °C
 

Tóm tắc thông số điện và hiệu suất của Bộ đếm Magnescale LT10A-205C

- Nguồn điện: 9,0 đến 26,4 V DC (thông qua đầu nối nguồn)
- Công suất tiêu thụ: Khoảng 2,5 W
- Độ phân giải: Có thể chọn 5 µm hoặc 10 µm
- Tốc độ phản hồi tối đa: 100 m/phút
 

Tóm tắc các chức năng và khả năng của Bộ đếm Magnescale LT10A-205C

- Chế độ đo: Giá trị hiện tại, giá trị tối đa, giá trị tối thiểu và giá trị đỉnh-đỉnh (P-P)
- Chức năng số học: Phép cộng và phép trừ 2 kênh (A+B, A-B, B-A)
- Bộ so sánh: Bộ so sánh 3 mức để đánh giá đạt/không đạt (Go/No-Go), tích hợp đèn LED và đầu ra I/O
- Đầu vào/đầu ra điều khiển: Thiết lập lại (Reset) và cài đặt trước (Preset) (thông qua các phím trên bảng điều khiển phía trước hoặc I/O bên ngoài)
- Giao tiếp: Giao diện RS-232C phục vụ trao đổi dữ liệu hai chiều và đầu vào kích hoạt (trigger) bên ngoài RS-TRG
 

Thông số kỹ thuật chi tiết của Bộ đếm Magnescale LT10A-205C 

- 1 I/O connector Input : Reset, peak-hold start, peak-hold pause, RS trigger (RS-232C models only) Output : Result evaluation (photocoupler)
- 2 BCD (36 pin half-pitch connector) Input : Reset, peak-hold start, comparator value selection (4 settings) Output : five digits (open collector)One of current value/maximum value/minimum value/peak-to-peakvalue selected and output. Alerm output
- 3 RS-232C (8 pin mini-DIN connector) Reset, preset value setting/recall, peak-hold start, peak-hold pause
- 4 RS-TRG pin Trigger input for RS-232C data output
- 5 With measuring unit connected.

Magnescale reserves the right to change product specifications without prior notice.
 

Model	LT10A-205C
Display	6 digit backlit LCD, mode display
I/O: Measuring unit input	2 CH
I/O connectors*1	○
I/O: BCD*2	–
I/O: RS-232C*3	○
I/O: RS-TRG*4	○
Reset function	Reset key or external input (I/O connectors)
	RS-232C command
Preset function	Preset value set with preset key, recalled with reset key.
	Set or recalled with RS-232C command
Conparetor function	Three-level comparator Comparator value set with keys on the front panel. Result evaluation: LED and I/O connector output (photocoupler)
	Set with RS-232C command
Peak Hold function	Maximum, minimum, and peak-to-peak values. Measuring started by the start input of the I/O connector; update stop by pause input.
	RS-232C can set or start.
Resolution	Selectable from 0.005 mm, 0.01 mm
Direction	Can be switched
Reference point function	Function use enabled/disabled can be selected (if use is enabled, the unit enters reference point signal input wait status at the same time as power-on).
Maximum response speed	100 m/min
Addition and subtraction function	A+B, A-B, B-A can be set with the direction setting.
Alarm	Speed over or measuring unit cable disconnected (Displayed on LCD or the I/O connector’s comparator outputs are all “H” (OFF).)
	–
Data storage	Resolution, direction, comparator value, preset value, modes, etc.
	Data signalling rate, etc.
key lock function	key lock and release.
Temperature	Operating:0～40℃, Storage:-10～50℃
Power consumption*5	2.5W
Mass	Approx. 230 g
Power supply	Power input connector (3 pins) : DC9.0-26.4 V
Compatible measuring unit	DT12/32series

 

Tham khảo thêm các models khác cùng loại, liên quan với Bộ đếm Magnescale LT10A-205C:

Model	LT10A-105
Display	6 digit backlit LCD, mode display
I/O: Measuring unit input	1 CH
I/O connectors*1	○
I/O: BCD*2	–
I/O: RS-232C*3	–
I/O: RS-TRG*4	–
Reset function	Reset key or external input (I/O connectors)
	–
Preset function	Preset value set with preset key, recalled with reset key.
	–
Conparetor function	Three-level comparator Comparator value set with keys on the front panel. Result evaluation: LED and I/O connector output (photocoupler)
	–
Peak Hold function	Maximum, minimum, and peak-to-peak values. Measuring started by the start input of the I/O connector; update stop by pause input.
	–
Resolution	Selectable from 0.005 mm, 0.01 mm
Direction	Can be switched
Reference point function	Function use enabled/disabled can be selected (if use is enabled, the unit enters reference point signal input wait status at the same time as power-on).
Maximum response speed	100 m/min
Addition and subtraction function	–
Alarm	Speed over or measuring unit cable disconnected (Displayed on LCD or the I/O connector’s comparator outputs are all “H” (OFF).)
	–
Data storage	Resolution, direction, comparator value, preset value, modes, etc.
	–
key lock function	key lock and release.
Temperature	Operating:0～40℃, Storage:-10～50℃
Power consumption*5	1.8W
Mass	Approx. 200 g
Power supply	Power input connector (3 pins) : DC9.0-26.4 V
Compatible measuring unit	DT12/32series

 

Model	LT10A-105B
Display	6 digit backlit LCD, mode display
I/O: Measuring unit input	1 CH
I/O connectors*1	○
I/O: BCD*2	○
I/O: RS-232C*3	–
I/O: RS-TRG*4	–
Reset function	Reset key or external input (I/O connectors)
	BCD terminal
Preset function	Preset value set with preset key, recalled with reset key.
	Recalled with BCD reset terminal
Conparetor function	Three-level comparator Comparator value set with keys on the front panel. Result evaluation: LED and I/O connector output (photocoupler)
	Up to 4 values can be set for comparator (key input). Switched with BCD terminal.
Peak Hold function	Maximum, minimum, and peak-to-peak values. Measuring started by the start input of the I/O connector; update stop by pause input.
	–
Resolution	Selectable from 0.005 mm, 0.01 mm
Direction	Can be switched
Reference point function	Function use enabled/disabled can be selected (if use is enabled, the unit enters reference point signal input wait status at the same time as power-on).
Maximum response speed	100 m/min
Addition and subtraction function	–
Alarm	Speed over or measuring unit cable disconnected (Displayed on LCD or the I/O connector’s comparator outputs are all “H” (OFF).)
	BCD alarm terminal “H” (OFF)
Data storage	Resolution, direction, comparator value, preset value, modes, etc.
	BCD sign
key lock function	key lock and release.
Temperature	Operating:0～40℃, Storage:-10～50℃
Power consumption*5	2.9W
Mass	Approx. 230 g
Power supply	Power input connector (3 pins) : DC9.0-26.4 V
Compatible measuring unit	DT12/32series

 

Model	LT10A-105C
Display	6 digit backlit LCD, mode display
I/O: Measuring unit input	1 CH
I/O connectors*1	○
I/O: BCD*2	–
I/O: RS-232C*3	○
I/O: RS-TRG*4	○
Reset function	Reset key or external input (I/O connectors)
	RS-232C command
Preset function	Preset value set with preset key, recalled with reset key.
	Set or recalled with RS-232C command
Conparetor function	Three-level comparator Comparator value set with keys on the front panel. Result evaluation: LED and I/O connector output (photocoupler)
	Set with RS-232C command
Peak Hold function	Maximum, minimum, and peak-to-peak values. Measuring started by the start input of the I/O connector; update stop by pause input.
	RS-232C can set or start.
Resolution	Selectable from 0.005 mm, 0.01 mm
Direction	Can be switched
Reference point function	Function use enabled/disabled can be selected (if use is enabled, the unit enters reference point signal input wait status at the same time as power-on).
Maximum response speed	100 m/min
Addition and subtraction function	–
Alarm	Speed over or measuring unit cable disconnected (Displayed on LCD or the I/O connector’s comparator outputs are all “H” (OFF).)
	–
Data storage	Resolution, direction, comparator value, preset value, modes, etc.
	Data signalling rate, etc.
key lock function	key lock and release.
Temperature	Operating:0～40℃, Storage:-10～50℃
Power consumption*5	2.0W
Mass	Approx. 220 g
Power supply	Power input connector (3 pins) : DC9.0-26.4 V
Compatible measuring unit	DT12/32series

 
 

Model	LT10A-205
Display	6 digit backlit LCD, mode display
I/O: Measuring unit input	2 CH
I/O connectors*1	○
I/O: BCD*2	–
I/O: RS-232C*3	–
I/O: RS-TRG*4	–
Reset function	Reset key or external input (I/O connectors)
	–
Preset function	Preset value set with preset key, recalled with reset key.
	–
Conparetor function	Three-level comparator Comparator value set with keys on the front panel. Result evaluation: LED and I/O connector output (photocoupler)
	–
Peak Hold function	Maximum, minimum, and peak-to-peak values. Measuring started by the start input of the I/O connector; update stop by pause input.
	–
Resolution	Selectable from 0.005 mm, 0.01 mm
Direction	Can be switched
Reference point function	Function use enabled/disabled can be selected (if use is enabled, the unit enters reference point signal input wait status at the same time as power-on).
Maximum response speed	100 m/min
Addition and subtraction function	A+B, A-B, B-A can be set with the direction setting.
Alarm	Speed over or measuring unit cable disconnected (Displayed on LCD or the I/O connector’s comparator outputs are all “H” (OFF).)
	–
Data storage	Resolution, direction, comparator value, preset value, modes, etc.
	–
key lock function	key lock and release.
Temperature	Operating:0～40℃, Storage:-10～50℃
Power consumption*5	2.3W
Mass	Approx. 210 g
Power supply	Power input connector (3 pins) : DC9.0-26.4 V
Compatible measuring unit	DT12/32series

 

Model	LT10A-205B
Display	6 digit backlit LCD, mode display
I/O: Measuring unit input	2 CH
I/O connectors*1	○
I/O: BCD*2	○
I/O: RS-232C*3	–
I/O: RS-TRG*4	–
Reset function	Reset key or external input (I/O connectors)
	BCD terminal
Preset function	Preset value set with preset key, recalled with reset key.
	Recalled with BCD reset terminal
Conparetor function	Three-level comparator Comparator value set with keys on the front panel. Result evaluation: LED and I/O connector output (photocoupler)
	Up to 4 values can be set for comparator (key input). Switched with BCD terminal.
Peak Hold function	Maximum, minimum, and peak-to-peak values. Measuring started by the start input of the I/O connector; update stop by pause input.
	–
Resolution	Selectable from 0.005 mm, 0.01 mm
Direction	Can be switched
Reference point function	Function use enabled/disabled can be selected (if use is enabled, the unit enters reference point signal input wait status at the same time as power-on).
Maximum response speed	100 m/min
Addition and subtraction function	A+B, A-B, B-A can be set with the direction setting.
Alarm	Speed over or measuring unit cable disconnected (Displayed on LCD or the I/O connector’s comparator outputs are all “H” (OFF).)
	BCD alarm terminal “H” (OFF)
Data storage	Resolution, direction, comparator value, preset value, modes, etc.
	BCD sign
key lock function	key lock and release.
Temperature	Operating:0～40℃, Storage:-10～50℃
Power consumption*5	4.0W
Mass	Approx. 270 g
Power supply	Power input connector (3 pins) : DC9.0-26.4 V
Compatible measuring unit	DT12/32series