Thông tin chi tiết của sản phẩm
Thiết bị kết hợp cắt sét và chống sét lan truyền T1+T2 cho điện mặt trời 1500vDC Phoenix Contact - VAL-MB-T1/T2 1500DC-PV/2+V - 2905641
Ưu điểm nổi bậc
- Tăng độ an toàn, nhờ tuân thủ tiêu chuẩn EN 50539-11
- Có tiếp điểm đáng tin cậy, nhờ vào chốt xoay tích hợp
- Dễ dàng thay thế, nhờ bộ phận ngắt cắm
- Bảo vệ biến tần tối ưu, nhờ mức bảo vệ thấp
- Thay thế hiệu quả các phích cắm bị lỗi, nhờ chỉ báo trạng thái trực quan
- Bảo vệ chống lại sự không khớp, nhờ vào các chốt và các bộ phận cơ bản
- Luôn là thiết bị chống sét phù hợp, nhờ vào các linh kiện bảo vệ loại 1 / loại 2 phổ dụng.
Hình ảnh thực tế và bản vẽ kỹ thuật

Dimensional drawing

Circuit diagram
Thông số kích thước tiêu chuẩn
Height |
120 mm |
Width |
71.2 mm |
Depth |
65.5 mm (incl. DIN rail 7.5 mm) |
Horizontal pitch |
4 Div. |
Thông số điều kiện môi trường hoạt động tiêu chuẩn
Degree of protection |
IP20 (only when all terminal points are used) |
Ambient temperature (operation) |
-40 °C ... 80 °C |
Ambient temperature (storage/transport) |
-40 °C ... 80 °C |
Altitude |
≤ 6000 m (amsl (above mean sea level)) |
Permissible humidity (operation) |
5 % ... 95 % |
Shock (operation) |
50g (Half-sine / 11 ms / 3x ±X, ±Y, ±Z) |
Vibration (operation) |
5g (5 - 500 Hz/2.5 h/X, Y, Z) |
Thông số chung tổng quát
IEC test classification |
PV I / II |
|
PV T1 / T2 |
EN type |
T1 / T2 |
IEC power supply system |
DC |
SPD failure behavior |
OCM (Open-circuit mode) |
Connection configuration |
Y configuration |
Installation location |
Inside |
Accessibility |
Accessible |
Installation location of the disconnect device |
Internal |
Mode of protection |
(L+) - (L-) |
|
(L+) - PE |
|
(L-) - PE |
Mounting type |
DIN rail: 35 mm |
Color |
traffic grey A RAL 7042 |
Housing material |
PA 6.6 |
Degree of pollution |
2 |
Flammability rating according to UL 94 |
V-0 |
Type |
DIN rail module, one-piece |
Surge protection fault message |
optical |
Mô tả bổ sung
Chú ý |
Sản phẩm cũng thích hợp cho các ứng dụng trong hệ thống điện mặt trười quang năng solar PV với mức dòng ngắn mạch tối đa ISC PV = 15 kA (theo EN 50539-11: 2013). |
Thông số bảo vệ mạch trong phạm vi điện áp DC
Maximum continuous operating voltage UCPV |
1500 V DC |
Open circuit voltage UOCSTC |
≤ 1250 V DC |
Short-circuit current rating ISCPV |
2000 A |
Continuous operating current ICPV |
< 100 µA |
Rated load current IL |
50 A |
Residual current IPE |
≤ 100 µA DC |
|
≤ 540 µA AC |
Standby power consumption PC |
≤ 150 mVA |
Nominal discharge current (8/20) µs |
20 kA |
Maximum discharge current Imax (8/20) µs |
40 kA |
Impulse discharge current (10/350) µs, charge |
3.125 As |
Impulse discharge current (10/350) µs, specific energy |
9.77 kJ/Ω |
Impulse discharge current (10/350) µs, peak value limp |
6.25 kA |
Total discharge current Itotal (8/20) µs |
40 kA |
Total discharge current Itotal (10/350) µs |
12.5 kA |
Voltage protection level Up |
≤ 4.5 kV |
Residual voltage Ures |
≤ 4.5 kV (at In) |
|
≤ 3.3 kV (at 3 kA) |
|
≤ 3.6 kV (at 6.25 kA) |
|
≤ 3.8 kV (at 10 kA) |
|
≤ 4.2 kV (at 15 kA) |
|
≤ 5.4 kV (at 40 kA) |
Response time tA |
≤ 25 ns |
Insulation resistance Riso |
> 5 GΩ (at 500 V DC) |
Thông số kết nối dữ liệu
Connection method |
Screw connection |
Screw thread |
M5 |
Tightening torque |
3 Nm |
Stripping length |
16 mm |
Conductor cross section flexible |
2.5 mm² ... 35 mm² |
2 conductors with same cross section, stranded, ferrules without plastic sleeve, min. |
2.5 mm² |
2 conductors with same cross section, stranded, ferrules without plastic sleeve, max. |
10 mm² |
Conductor cross section AWG |
14 ... 2 |
Tiêu chuẩn và Quy định
Standards/regulations |
EN 50539-11 2013 |
Tiêu chuẩn phân lớp Classifications
eCl@ss
eCl@ss 5.1 |
27130800 |
eCl@ss 6.0 |
27130800 |
eCl@ss 7.0 |
27130802 |
eCl@ss 8.0 |
27130802 |
eCl@ss 9.0 |
27130802 |
ETIM
ETIM 3.0 |
EC000941 |
ETIM 4.0 |
EC000381 |
ETIM 5.0 |
EC000381 |
ETIM 6.0 |
EC000381 |
UNSPSC
Approvals