Bộ nguồn Siemens 6EP1334-3BA10 | SITOP PSU200M 10 A | 120/230-500VAC 24VDC 10A

Article number

6EP1334-3BA10

6EP1334-3BA10-8AB0

Product

SITOP PSU200M

SITOP PSU200M

Power supply, type

24 V/10 A

24 V/10 A

Input

Input

1-phase and 2-phase AC

1-phase and 2-phase AC

Supply voltage

- 1 at AC

120 ... 230 V

120 ... 230 V

- 2 at AC

230 ... 500 V

230 ... 500 V

- Note

Set by means of selector switch on the device

Set by means of selector switch on the device

Input voltage

- 1 at AC

85 ... 264 V

85 ... 264 V

- 2 at AC

176 ... 550 V

176 ... 550 V

Wide-range input

Yes

Yes

Overvoltage resistance

1300 Vpeak, 1.3 ms

1300 Vpeak, 1.3 ms

Mains buffering at Iout rated, min.

25 ms; at Vin = 120/230 V, typ. 150 ms at Vin = 400 V

25 ms; at Vin = 120/230 V, typ. 150 ms at Vin = 400 V

Rated line frequency 1

50 Hz

50 Hz

Rated line frequency 2

60 Hz

60 Hz

Rated line range

47 ... 63 Hz

47 ... 63 Hz

Input current

- at rated input voltage 120 V

4.4 A

4.4 A

- at rated input voltage 230 V

2.4 A

2.4 A

- at rated input voltage 500 V

1.1 A

1.1 A

Switch-on current limiting (+25 °C), max.

35 A

35 A

I²t, max.

4 A²·s

4 A²·s

Built-in incoming fuse

T 6.3 A (not accessible)

T 6.3 A (not accessible)

Protection in the mains power input (IEC 898)

Recommended miniature circuit breaker at 1-phase operation: from 6 A (10 A) characteristic C (B); required at 2-phase operation: circuit breaker 2-pole connected or circuit breaker 3RV2011-1EA10 (setting 3.8 A) or 3RV2711-1ED10 (UL 489) at 230 V; 3RV2011-1DA10 (setting 3 A) or 3RV2711-1DD10 (UL 489) at 400/500 V

Recommended miniature circuit breaker at 1-phase operation: from 6 A (10 A) characteristic C (B); required at 2-phase operation: circuit breaker 2-pole connected or circuit breaker 3RV2011-1EA10 (setting 3.8 A) or 3RV2711-1ED10 (UL 489) at 230 V; 3RV2011-1DA10 (setting 3 A) or 3RV2711-1DD10 (UL 489) at 400/500 V

Output

Output

Controlled, isolated DC voltage

Controlled, isolated DC voltage

Rated voltage Vout DC

24 V

24 V

Total tolerance, static ±

3 %

3 %

Static mains compensation, approx.

0.1 %

0.1 %

Static load balancing, approx.

0.1 %

0.1 %

Residual ripple peak-peak, max.

50 mV

50 mV

Spikes peak-peak, max. (bandwidth: 20 MHz)

200 mV

200 mV

Adjustment range

24 ... 28.8 V

24 ... 28.8 V

Product function Output voltage adjustable

Yes

Yes

Output voltage setting

via potentiometer

via potentiometer

Status display

Green LED for 24 V OK

Green LED for 24 V OK

Signaling

Relay contact (NO contact, rating 60 V DC/ 0.3 A) for "24 V OK"

Relay contact (NO contact, rating 60 V DC/ 0.3 A) for "24 V OK"

On/off behavior

Overshoot of Vout approx. 3 %

Overshoot of Vout approx. 3 %

Startup delay, max.

1 s

1 s

Voltage rise, typ.

50 ms

50 ms

Rated current value Iout rated

10 A

10 A

Current range

0 ... 10 A

0 ... 10 A

- Note

+60 ... +70 °C: Derating 2%/K (at 120 V, 230 V) or 3.5%/K (at 400 V)

+60 ... +70 °C: Derating 2%/K (at 120 V, 230 V) or 3.5%/K (at 400 V)

Supplied active power typical

240 W

240 W

Short-term overload current

- at short-circuit during operation typical

30 A

30 A

Duration of overloading capability for excess current

- at short-circuit during operation

25 ms

25 ms

Constant overload current

- on short-circuiting during the start-up typical

12 A

12 A

Parallel switching for enhanced performance

Yes; switchable characteristic

Yes; switchable characteristic

Numbers of parallel switchable units for enhanced performance

2

2

Efficiency

Efficiency at Vout rated, Iout rated, approx.

91 %

91 %

Power loss at Vout rated, Iout rated, approx.

24 W

24 W

Power loss [W] during no-load operation maximum

6 W

6 W

Closed-loop control

Dynamic mains compensation (Vin rated ±15 %), max.

0.1 %

0.1 %

Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ.

3 %

3 %

Load step setting time 50 to 100%, typ.

2 ms

2 ms

Load step setting time 100 to 50%, typ.

2 ms

2 ms

Setting time maximum

5 ms

5 ms

Protection and monitoring

Output overvoltage protection

< 35 V

< 35 V

Current limitation, typ.

12 A

12 A

Property of the output Short-circuit proof

Yes

Yes

Short-circuit protection

Alternatively, constant current characteristic approx. 12 A or latching shutdown

Alternatively, constant current characteristic approx. 12 A or latching shutdown

Enduring short circuit current RMS value

- typical

12 A

12 A

Overload/short-circuit indicator

LED yellow for "overload", LED red for "latching shutdown"

LED yellow for "overload", LED red for "latching shutdown"

Safety

Primary/secondary isolation

Yes

Yes

Galvanic isolation

Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178

Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178

Protection class

Class I

Class I

Leakage current

- maximum

3.5 mA

3.5 mA

- typical

0.32 mA

0.32 mA

CE mark

Yes

Yes

UL/cUL (CSA) approval

cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259

cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259

Explosion protection

IECEx Ex nA nC IIC T4 Gc; ATEX (EX) II 3G Ex nA nC IIC T4 Gc (für AC 120-230/230-400 V); cCSAus (CSA C22.2 No. 213, ANSI/ISA-12.12.01) Class I, Div. 2, Group ABCD, T3

IECEx Ex nA nC IIC T4 Gc; ATEX (EX) II 3G Ex nA nC IIC T4 Gc (für AC 120-230/230-400 V); cCSAus (CSA C22.2 No. 213, ANSI/ISA-12.12.01) Class I, Div. 2, Group ABCD, T3

CB approval

Yes

Yes

Marine approval

GL, ABS

GL, ABS

Degree of protection (EN 60529)

IP20

IP20

EMC

Emitted interference

EN 55022 Class B

EN 55022 Class B

Supply harmonics limitation

EN 61000-3-2

EN 61000-3-2

Noise immunity

EN 61000-6-2

EN 61000-6-2

Operating data

Ambient temperature

- during operation

-25 ... +70 °C

-25 ... +70 °C

-  Note

With natural convection; startup tested starting from -40 °C nominal voltage

with natural convection

- during transport

-40 ... +85 °C

-40 ... +85 °C

- during storage

-40 ... +85 °C

-40 ... +85 °C

Humidity class according to EN 60721

Climate class 3K3, no condensation

Climate class 3K3, no condensation

Mechanics

Connection technology

screw-type terminals

screw-type terminals

Connections

- Supply input

L, N, PE: 1 screw terminal each for 0.2 ... 2.5 mm² single-core/finely stranded

L, N, PE: 1 screw terminal each for 0.2 ... 2.5 mm² single-core/finely stranded

- Output

+, -: 2 screw terminals each for 0.2 ... 2.5 mm²

+, -: 2 screw terminals each for 0.2 ... 2.5 mm²

- Auxiliary

13, 14 (alarm signal): 1 screw terminal each for 0.14 ... 1.5 mm²

13, 14 (alarm signal): 1 screw terminal each for 0.14 ... 1.5 mm²

Width of the enclosure

70 mm

70 mm

Height of the enclosure

125 mm

125 mm

Depth of the enclosure

121 mm

121 mm

Required spacing

- top

50 mm

50 mm

- bottom

50 mm

50 mm

- left

0 mm

0 mm

- right

0 mm

0 mm

Weight, approx.

0.8 kg

0.8 kg

Product feature of the enclosure housing for side-by-side mounting

Yes

Yes

Installation

Snaps onto DIN rail EN 60715 35x7.5/15

Snaps onto DIN rail EN 60715 35x7.5/15

Electrical accessories

Buffer module

Buffer module

MTBF at 40 °C

1 055 408 h

1 055 408 h

Other information

Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)

Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)

SITOP PSE201U buffer module

6EP1961-3BA01

For SITOP smart and SITOP modular
buffer time 100 ms to 10 s 
dependent on load current 

SITOP PSE202U redundancy module

6EP1961-3BA21

Input/output: 24 V DC/40 A 
suitable for decoupling two SITOP power supplies with a maximum of 20 A output current

SITOP PSE202U redundancy module

6EP1962-2BA00

Input/output: 24 V DC/NEC Class 2 
suitable for decoupling two SITOP power supplies; 
output power limited < 100 VA

SITOP PSE202U redundancy module

6EP1964-2BA00

Input/output: 24 V DC/10 A 
suitable for decoupling two SITOP power supplies with a maximum of 5 A output current

SITOP PSE200U 3 A selectivity module

4-channel selectivity module
Input: 24 V DC
Output: 24 V DC/3 A per channel 
Adjustable response threshold 0.5 … 3 A

6EP1961-2BA11

6EP1961-2BA31

SITOP PSE200U 3 A NEC Class 2 selectivity module

4-channel selectivity module 
Input: 24 V DC 
Output: 24 V DC/3 A per channel 
Adjustable response threshold 0.5 … 3 A

6EP1961-2BA51

6EP1961-2BA61

SITOP PSE200U 10 A selectivity module

4-channel selectivity module
Input: 24 V DC
Output: 24 V DC/10 A per channel 
Adjustable response threshold 3 … 10 A

6EP1961-2BA21

6EP1961-2BA41

Device labeling plates

3RT2900-1SB20