Chi tiết thông tin đặc tính sản phẩm
Driver điều khiển độ sáng đèn LED với điện áp không đổi 1-10V và trình điều khiển LED PUSH DIM 75w 12Vdc - Merrytek - ML75V-PV
Basic Information
Place of Origin:China
Certification:CE
Model Number:ML75V-PV
Detail Information
Product Name: Constant Voltage 1-10V And PUSH DIM LED Driver 75w 12Vdc
Output Load: 75W Max
Output Current: 6.25A Max
Output Voltage: 12Vdc
Efficiency: ≥85%
Certification: CE
Protection Class: IP20
Life Time: 50000
Dimming Mode: 0-10V, 1-10V, Push
Product Description
ML75V-PV Constant Voltage 1-10V and PUSH DIM LED Driver 75w 12Vdc 220x58x40mm
Description
1. Output voltage:12Vdc.
2. Ouput power: 75w Max
3. Output current: 6.25A max
4. Dimming mode include 0-10V,1-10V,Push dim.
5. With top circuit design, AC-DC-DC, no flicker.
6. Synchronization: thanks to the MCU programme, up to 15pcs drivers should be controlled by the same switch. This means there is no need for any additional synchrony wire in larger installations, where many drivers should be controlled by one switch.
7. Memory function: The driver has built-in permanent memory against power failure. Lights can return to previous dimming level when switch off and on again, even at mains restores.
8. Press-in terminals in primary and secondary side, easy assembly.
9. Maximum length of the cable, from switch to last driver is 20m.
10. Factory setting: 100% dimming level.
11. Protection: Short circuit / Over voltage / Over temperature.
12. 50,000 hours life time,5 years warranty.
Mechanical Specification
PUSH BUTTON SWITCH FOR DIMMING
- Primary push dimming is prior and always active
- On/Off: Short push on the switch
- Stepless dimming: Long push on the switch. With every other long push, the light level goes the opposite direction
- Bult-in with permanent memory: Ling returns to the previous dimming level when switched off and on again, even at power fallure
MIN DIMMING LEVEL SETTING (Fig.A)
- Turn on the driver and dim to the required minimum dimming level. Short push the key to temember the min level.
- Long push (>3 sec) the key can restore the factory default setting. Factory setting of min. dimming level is 2%
1-10V DIMMER (Fig. B -C)
- Factory setting: 1-10V dimming
- Notel Using primary push dimming will make 1-10V dimming inactivated. It has to handle as following steps when change push dimming to 1-10V interface, then power on LED driver for at least 5 seconds.
+ Turn off the LED driver and short circuit of 1-10V and power on, 1-10V dimming is active.
+ Remove short-circuit of 1-10V and power on, 1-10V dimming is active.
SYNCHRONIZATION
No need additional synchrony wire in larger installations, up to 15pcs drivers when connected to the sam switch.
Ignore |
To avoid reaction on AC spike |
<0.05sec |
Short push |
Turn on or off |
0.1-1sec |
Long push |
Dimming up or down |
1.5-10sec |
Notel Continuously short push with an interval less than 1 sec may cause different dim level as MCU couldn't respond to the fast signal change. For the resynchronization to work correctly when more than one driver is connected to the same push button, please follow the steps below:
- Press the push button for more than one second (long push), followed by a short push (<1s)
- Now that the devices are switched off, do a long push, the system will now be resynchronized
Specifications
Model NO. |
ML75V-PV1 |
Input |
Input voltage |
220-240Vac, 50/60Hz |
Power factor (PF) |
≥0.9(@ 240Vac input, full load and without dimmer) |
Efficiency |
≥82%(@ 240Vac input, full load and without dimmer) |
Stand-by power |
≤0.5W |
Max. output voltage |
24V DC |
Output |
Output current |
12V DC, 6.25A max. |
Voltage accuracy |
±5% |
Rated power |
75W Max. |
Dimming mode |
0-10V,1-10V, PUSH |
Dimming |
Dimming range |
0%-100% |
Working temperature |
-25℃~50℃ |
Environment |
Storage temperature |
-40℃~80℃ |
Insulation class |
Class II, SELV |
Safety and EMC |
Withstand voltage |
Input-Output: 3.75kVac/5mA/1min |
EMC |
Compliance to EN55015, EN61000-3-2 Class C, EN61000-3-3, EN61547 |
Safety |
Compliance to EN61347-1, EN61347-2-13, EN60598-1, EN60598-2-6 |
Short circuit |
Protection mode: Auto recovery |
Protection |
Over temperature |
Protection mode: Auto recovery |
Dimension |
202x58x40mm |
Others |
Enclosure |
Plastic, white |
IP rating |
IP20 |
Connection |
Input: 6-hole press-in type terminal(L, L, N, N) |
Output: Screw terminal block (LED +, LED -) , (1-10V+,1-10V-) , (1-10V+,1-10V-) |
Life time |
50,000h |
Certification |
CE |
Packing |
Bubble bag + cardboard + Carton |
Applications
For LED panel light, LED down light, led strip, led tube etc…
Wire diagram
Tham khảo các Model LED driver chỉnh sáng khác của Merrytek
1x10w Push / 1-10v LED Dimmer Switch / High Efficiency LED Driver 0-10V
Model Number:
ML10C-PV
Product Name: 10w 1-10V & Push Dimmable Led Driver
Input Voltage: 220-240Vac
Dimming Mode: 1-10V,push Dim
Output Current: 350mA
Output Voltage: 6-30Vdc
Dimming Range: 2%~100%
Life Time: 50,000 Hours
IP Rating: IP 20
Working Temperature: -25℃-50℃
Isolation Class: Class Ⅱ
1x10w Push 1-10v led dimmer switch ML10C- PV1For 700mA Output 6-14Vdc
Model Number:
ML10C-PV1
Product Name: 10w 1-10V & Push Dimmable Led Driver
Input Voltage: 220-240Vac
Dimming Mode: 1-10V,push Dim
Output Current: 700mA
Output Voltage: 3-15Vdc
Dimming Range: 2%~100%
Life Time: 50,000 Hours
IP Rating: IP 20
Working Temperature: -25℃-50℃
Protection Class: IP20
25W non flickering 1-10V / PUSH dimming LED power supply Energy saving
Model Number:
ML25C-PV
Product Name: 25W Dimming LED Power Supply
Output Load: 1 X 25W Max.
Stand-by Power: ≤0.5W
Output Voltage: 68Vdc Max.
Input Voltage: 220~240Vac
Dimming Mode: 1-10V, PUSH
Working Temperature: -25℃-50℃
Isolation Class: Class Ⅱ
Approvals: SEMKO/ CE/ RoHS
Protection Class: IP20
1-10V Dimmable LED Driver 250 – 700mA , High Efficiency LED Dimming Driver
Model Number:
ML30C-PV
Product Name: Dimming Led Driver
Output Load: 30W Max
Stand-by Power: ≤0.5W
Output Voltage: 68Vdc Max
Efficiency: ≥84%
Input Currenct: 0.18A Max
Certification: CE,SEMKO, RoHS
Protection Class: IP20
Life Time: 50000 Hours
Power Factor: ≥0.9
High Power 2 x 25W Two Channel Output 700ma Dimmable LED Driver 0-10v
Model Number:
ML50C2-PV
Product Name: Two Channel 0-10V /PUSH Dimming Led Driver
Dimming Mode: 0-10V And Pusn
Input Voltage: 220-240Vac
Rated Load: 2x25W Max
Output Channel Qty: Two-channel
Output Current: 250mA-700mA, Selectable Via DIP Switch
Output Voltage: 68Vdc Max.
Approvals: SEMKO /CE
Working Temperature: -25℃-50℃
ML50C-PV 1x50w 0-10V / Push LED Driver Dimmable 350mA - 1050mA Multi - Output
Model Number:
ML50C-PV
Output Voltage: 68Vdc Max
Input Voltage: 220-240Vac
Dimming Mode: 0-10V,push
Production Name: Dimming Led Driver
Output Current: 350-1050mA Selectable Via DIP Switch
Input Current: 0.26mA Max
Output Load Range: 50W Max
Protection Class: IP20
Life Time: 50000hours
Certification: SEMKO /CE /RoHS
Multi - Output 1-10V Dimmable LED Driver 50W For LED Panel Light , RoHS
Model Number:
ML50C-PV2
Product Name: 1x50w 0-10V And PUSH DIM Led Driver Slim Design
Input Voltage: 220-240Vac
Outut Current: 350mA - 1050mA Set Via Dip Switches
Output Voltage: 1 X 50w Max
Dimming Mode: 0-10V,PUSH DIM
Dimming Range: 0 - 100%
Protection Class: IP20
Life Time: 50000hours
Certification: CE /RoHS
Professional Constant Voltage Dimmable LED Driver 0-10V 75w 220x58x40mm
Model Number:
ML75V-PV
Product Name: Constant Voltage 1-10V And PUSH DIM LED Driver 75w 12Vdc
Output Load: 75W Max
Output Current: 6.25A Max
Output Voltage: 12Vdc
Efficiency: ≥85%
Certification: CE
Protection Class: IP20
Life Time: 50000
Dimming Mode: 0-10V,1-10V ,Push
IP20 Constant Voltage Dimmable LED Driver 1-10V , PUSH DIM LED Driver 24Vdc 75w
Model Number:
ML75V-PV1
Product Name: Constant Voltage 1-10V And PUSH DIM LED Driver 75w 24Vdc
Output Load: 75W Max
Output Current: 3.125A Max
Output Voltage: 24vdc
Efficiency: ≥85%
Certification: CE
Protection Class: IP20
Life Time: 50000
Dimming Mode: 0-10V,1-10V ,Push