Relay module rơle PLC-RSC 1PDT 250v AC/DC 24vDC 6A - Phoenix Contact - Relay Module - PLC-RPT- 24DC/ 1IC/ACT - 2900298

THÔNG TIN THAM KHẢO

• Danh mục Model sản phẩm PHOENIX CONTACT

• 

  Full Video về Sự khác nhau giữa Contactor và Relay

• 

  Rờ le giám sát dòng Siemens SIRIUS 3RR24 cho 3RT2

• Xem thêm

Chi tiết thông tin đặc tính sản phẩm

Relay module rơle PLC-RSC 1PDT 250v AC/DC 24vDC 6A - Phoenix Contact - Relay Module - PLC-RPT- 24DC/ 1IC/ACT - 2900298

Bản vẽ kỹ thuật

Diagram
Curve A
Maximum permissible continuous voltage Umax with limiting continuous current on the contact side (see relevant technical data)
Curve B
Minimum permissible operate voltage Uop after pre-excitation (see relevant technical data)


Diagram
Interrupting rating


Diagram
Basic behavior of capacitive loads:
- Very high inrush current
- Voltage increases with an e-function


Circuit diagram

 

Chú ý

Utilization restriction

EMC: class A product, see manufacturer's declaration in the download area

 

Thông số kích thước

Width	14 mm
Height	80 mm
Depth	94 mm

 

Thông số điều kiện môi trường hoạt động

Ambient temperature (operation)	-40 °C ... 60 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C

 

Thông số cuộn dây

Nominal input voltage UN	24 V DC
Typical input current at UN	18 mA
Typical response time	8 ms
Typical release time	10 ms
Protective circuit	Reverse polarity protection Polarity protection diode
	Free-wheeling diode Damping diode
Operating voltage display	Yellow LED
Power dissipation for nominal condition	0.43 W

 

Thông số Contact side

Contact type	1 N/O contact
Type of switch contact	Single contact
Contact material	AgSnO
Maximum switching voltage	250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...)
Minimum switching voltage	12 V (at 100 mA)
Min. switching current	100 mA (at 12 V DC)
Maximum inrush current	80 A (20 ms)
	130 A (peak, at capacitive load, 230 V AC, 24 μF)
Limiting continuous current	6 A
	10 A (the value is permissible if both connections 13, both connections 14 and both connections BB are bridged)
Interrupting rating (ohmic load) max.	144 W (at 24 V DC)
	58 W (at 48 V DC)
	48 W (at 60 V DC)
	50 W (at 110 V DC)
	80 W
	85 W (for 250 V DC)
	1500 VA (for 250 V AC)
Interrupting rating (ohmic load) max. bridged	240 W (for 24 V DC. The value is permissible if both connections 13, both connections 14 and both connections BB are bridged.)
	2500 VA (for 250 V AC. The value is permissible if both connections 13, both connections 14 and both connections BB are bridged.)
Switching capacity min.	1200 mW
Switching capacity	2 A (at 24 V, DC13)
	0.2 A (at 110 V, DC13)
	0.2 A (at 250 V, DC13)
	6 A (at 24 V, AC15)
	6 A (at 120 V, AC15)
	6 A (at 250 V, AC15)

 

Thông số kết nối dữ liệu đầu vào

Connection name	Coil side
Connection method	Push-in connection
Stripping length	8 mm
Conductor cross section solid	0.14 mm² ... 2.5 mm²
Conductor cross section flexible	0.14 mm² ... 2.5 mm²
	0.2 mm² ... 2.5 mm² ()
	2x 0.5 mm² ... 1 mm² ()
Conductor cross section AWG	26 ... 14

 

Thông số kết nối dữ liệu đầu ra

Connection name	Contact side
Connection method	Push-in connection
Stripping length	8 mm
Conductor cross section solid	0.14 mm² ... 2.5 mm²
Conductor cross section flexible	0.14 mm² ... 2.5 mm²
	0.2 mm² ... 2.5 mm² ()
	2x 0.5 mm² ... 1 mm² ()
Conductor cross section AWG	26 ... 14

 

Thông số chung

Note	Separating plate PLC-ATP must be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules.
	The PLC-ATP separating plate should be installed for safe isolation between adjacent modules
	The PLC-ATP separating plate is required at the start and end of every PLC terminal strip.
	The system installer must ensure the touch protection of the product (at voltages > 25 V AC/60 V DC). The product is a built-in device without protection against direct contact.
Test voltage relay winding/relay contact	4 kV AC (50 Hz, 1 min.)
Operating mode	100% operating factor
Degree of protection	RT II (Relay)
	IP20 (Relay base)
Mechanical service life	3x 107 cycles
Mounting position	any
Assembly instructions	In rows with zero spacing

 

Các quy chuẩn đạt được

Connection in acc. with standard	CUL
Designation	Standards/regulations
Standards/regulations	EN 50178
	EN 61810-1
Rated insulation voltage	250 V AC
Rated surge voltage	6 kV
Insulation	Safe isolation, reinforced insulation
Degree of pollution	2
Overvoltage category	III
Flammability rating according to UL 94	V0

 

Tiêu chuẩn thân thiện môi trường

China RoHS	Environmentally Friendly Use Period = 50
	For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration”

 

Các bộ phận cấu thành

Relay base PLC-BPT- 24DC/ 1IC/ACT 2900260
14 mm PLC basic terminal block for high switch-on currents with push-in connection, without relay or solid-state relay, for mounting on DIN rail NS 35/7,5, with load return line connection (BB), 1 N/O contact, input voltage 24 V DC

Single relay REL-MR- 24DC/1IC 2961341
Plug-in miniature power relay, with power contact for high switch-on currents, 1 N/O contact, input voltage 24 V DC

 

Approvals 

 

- Download Tài liệu kỹ thuật Catalogue Datasheet Relay module rơle PLC-RSC 1PDT 250v AC/DC 24vDC 6A - Phoenix Contact - Relay Module - PLC-RPT- 24DC/ 1IC/ACT - 2900298

 

- Download Tài liệu hướng dẫn sử dụng Relay module rơle PLC-RSC 1PDT 250v AC/DC 24vDC 6A - Phoenix Contact - Relay Module - PLC-RPT- 24DC/ 1IC/ACT - 2900298