Bộ nguồn Siemens 6EP1336-3BA10 | SITOP PSU8200 20 A | 120-230VAC 110-220VDC 24VDC 20A

Article number

6EP1336-3BA10

Product

6EP1336-3BA10 - SITOP PSU8200 

Power supply, type

24 V/20 A

Input

Input

1-phase AC or DC

Supply voltage

- 1 at AC Rated value

- 2 at AC Rated value

- at DC

110 ... 220 V

Rated voltage value Vin rated

120 ... 230 V

Voltage range AC

85 ... 275 V

- Note

Derating of temperature necessary down to 50 °C at Vin < 100 V AC or DC

Input voltage

- 1 at AC

- 2 at AC

- at DC

88 ... 350 V

Wide-range input

Yes

Mains buffering at Iout rated, min.

20 ms; at Vin = 230 V

Rated line frequency 1

50 Hz

Rated line frequency 2

60 Hz

Rated line range

45 ... 65 Hz

Input current

- at rated input voltage 120 V

4.6 A

- at rated input voltage 230 V

2.5 A

Switch-on current limiting (+25 °C), max.

20 A

I²t, max.

5 A²·s

Built-in incoming fuse

Yes

Protection in the mains power input (IEC 898)

Recommended miniature circuit breaker at 1-phase operation: 10 A characteristic C; required at 2-phase operation: circuit breaker 2-pole connected or circuit breaker 3RV2711-1HD10 (UL 489) at 120 V or 3RV2711-1ED10 (UL 489) at 230 V

Output

Output

Controlled, isolated DC voltage

Rated voltage Vout DC

24 V

Total tolerance, static ±

3 %

Static mains compensation, approx.

0.1 %

Static load balancing, approx.

0.3 %

Residual ripple peak-peak, max.

100 mV

Residual ripple peak-peak, typ.

80 mV

Spikes peak-peak, max. (bandwidth: 20 MHz)

200 mV

Spikes peak-peak, typ. (bandwidth: 20 MHz)

100 mV

Adjustment range

24 ... 28.8 V

Product function Output voltage adjustable

Yes

Output voltage setting

via potentiometer

Status display

Green LED for 24 V OK

Signaling

Relay contact (NO contact, rating 60 V DC/ 0.3 A) for "24 V OK"

On/off behavior

No overshoot of Vout (soft start)

Startup delay, max.

0.25 s

Voltage rise, typ.

50 ms

Rated current value Iout rated

20 A

Current range

0 ... 20 A

- Note

+60 ... +70 °C: Derating 3%/K

Supplied active power typical

480 W

Short-term overload current

- on short-circuiting during the start-up typical

- at short-circuit during operation typical

60 A

Duration of overloading capability for excess current

- on short-circuiting during the start-up

- at short-circuit during operation

25 ms

Constant overload current

- on short-circuiting during the start-up typical

30 A

Parallel switching for enhanced performance

Yes; switchable characteristic

Numbers of parallel switchable units for enhanced performance

2

Efficiency

Efficiency at Vout rated, Iout rated, approx.

93 %

Power loss at Vout rated, Iout rated, approx.

42 W

Power loss [W] during no-load operation maximum

Closed-loop control

Dynamic mains compensation (Vin rated ±15 %), max.

0.5 %

Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ.

1 %

Load step setting time 50 to 100%, typ.

1 ms

Load step setting time 100 to 50%, typ.

1 ms

Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ.

Load step setting time 10 to 90%, typ.

Load step setting time 90 to 10%, typ.

Setting time maximum

5 ms

Protection and monitoring

Output overvoltage protection

< 33 V

Current limitation, typ.

21.5 A

Property of the output Short-circuit proof

Yes

Short-circuit protection

Alternatively, constant current characteristic approx. 23 A or latching shutdown

Enduring short circuit current RMS value

- typical

23 A

Overcurrent overload capability in normal operation

overload capability 150 % Iout rated up to 5 s/min

Overload/short-circuit indicator

LED yellow for "overload", LED red for "latching shutdown"

Safety

Primary/secondary isolation

Yes

Galvanic isolation

Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178

Protection class

Class I

Leakage current

- maximum

3.5 mA

- typical

1 mA

CE mark

Yes

UL/cUL (CSA) approval

cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259

Explosion protection

IECEx Ex nA nC IIC T3 Gc; ATEX (EX) II 3G Ex nA nC IIC T3 Gc; cCSAus (CSA C22.2 No. 213, ANSI/ISA-12.12.01) Class I, Div. 2, Group ABCD, T3

FM approval

-

CB approval

No

Marine approval

GL, ABS

Degree of protection (EN 60529)

IP20

EMC

Emitted interference

EN 55022 Class B

Supply harmonics limitation

EN 61000-3-2

Noise immunity

EN 61000-6-2

Operating data

Ambient temperature

- during operation

-25 ... +70 °C

- Note

With natural convection; startup tested starting from -40 °C nominal voltage

- during transport

-40 ... +85 °C

- during storage

-40 ... +85 °C

Humidity class according to EN 60721

Climate class 3K3, no condensation

Mechanics

Connection technology

screw-type terminals

Connections

- Supply input

L, N, PE: 1 screw terminal each for 0.2 ... 4 mm² single-core/finely stranded

- Output

+, -: 2 screw terminals each for 0.2 ... 4 mm²

- Auxiliary

13, 14 (alarm signal): 1 screw terminal each for 0.14 ... 1.5 mm²

Width of the enclosure

90 mm

Height of the enclosure

125 mm

Depth of the enclosure

125 mm

Required spacing

- top

50 mm

- bottom

50 mm

- left

0 mm

- right

0 mm

Weight, approx.

1.2 kg

Product feature of the enclosure housing for side-by-side mounting

Yes

Installation

Snaps onto DIN rail EN 60715 35x7.5/15

Electrical accessories

Buffer module

Mechanical accessories

Device identification label 20 mm × 7 mm, pale turquoise 3RT1900-1SB20

MTBF at 40 °C

667 048 h

Other information

Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)

SITOP PSE201U buffer module

6EP1961-3BA01

For SITOP smart and SITOP modular
buffer time 100 ms to 10 s 
dependent on load current 

SITOP modular signaling module

6EP1961-3BA10

For 6EP1XXX-3BA00 
signaling contacts: Output voltage OK,

readiness for operation OK, remote ON/OFF

SITOP PSE202U redundancy module

6EP1961-3BA21

Input/output: 24 V DC/40 A 
suitable for decoupling two SITOP power supplies with a maximum of 20 A output current

SITOP PSE202U redundancy module

6EP1962-2BA00

Input/output: 24 V DC/NEC Class 2 
suitable for decoupling two SITOP power supplies; 
output power limited < 100 VA

SITOP PSE202U redundancy module

6EP1964-2BA00

Input/output: 24 V DC/10 A 
suitable for decoupling two SITOP power supplies with a maximum of 5 A output current

SITOP PSE200U 3 A selectivity module

4-channel selectivity module
Input: 24 V DC
Output: 24 V DC/3 A per channel 
Adjustable response threshold 0.5 … 3 A

6EP1961-2BA11

6EP1961-2BA31

SITOP PSE200U 3 A NEC Class 2 selectivity module

4-channel selectivity module 
Input: 24 V DC 
Output: 24 V DC/3 A per channel 
Adjustable response threshold 0.5 … 3 A

6EP1961-2BA51

6EP1961-2BA61

SITOP PSE200U 10 A selectivity module

4-channel selectivity module
Input: 24 V DC
Output: 24 V DC/10 A per channel 
Adjustable response threshold 3 … 10 A

6EP1961-2BA21

6EP1961-2BA41

Device labeling plates

3RT2900-1SB20