Rờ le dẹp Phoenix Contact PLC-RSC- 24DC/21AU - 2966265 | Relay Module
(PLC-INTERFACE 1PDT 250V AC/DC 6A AU coil 24VDC)
PLC-INTERFACE, consisting of PLC-BSC.../21 basic terminal block with screw connection and plug-in miniature relay with multi-layer gold contact, for mounting on DIN rail NS 35/7,5, 1 changeover contact, input voltage 24 V DC
Your advantages
- Slim design
- Efficient connection to system cabling using V8 adapter
- RT III sealed relay
- Safe isolation according to DIN EN 50178 between coil and contact
- Functional plug-in bridges
- Integrated input circuit and interference suppression circuit
Drawings
Diagram
Curve A
Maximum permissible continuous voltage Umax with limiting continuous current on the contact side (see relevant technical data)
Curve B
Minimum permissible operate voltage Uop after pre-excitation (see relevant technical data)
Diagram
Limiting continuous current per contact for 0.85 ... 1.1 UN (contact-side)
(1) Limiting continuous current for horizontal installation position without clearance
(2) Limiting continuous current for vertical installation position without clearance
Circuit diagram
Note
Utilization restriction |
EMC: class A product, see manufacturer's declaration in the download area |
Dimensions
Width |
6.2 mm |
Height |
80 mm |
Depth |
94 mm |
Ambient conditions
Ambient temperature (operation) |
-40 °C ... 70 °C (see to derating) |
Ambient temperature (storage/transport) |
-40 °C ... 85 °C |
Degree of protection |
IP20 (Relay base) |
Coil side
Nominal input voltage UN |
24 V DC |
Typical input current at UN |
9 mA |
Typical response time |
5 ms |
Typical release time |
8 ms |
Protective circuit |
Reverse polarity protection Polarity protection diode |
|
Free-wheeling diode Damping diode |
Operating voltage display |
Yellow LED |
Power dissipation for nominal condition |
0.22 W |
Contact side
Contact type |
1 changeover contact |
Type of switch contact |
Single contact |
Contact material |
AgSnO, hard gold-plated |
Maximum switching voltage |
30 V AC |
|
36 V DC |
Minimum switching voltage |
100 mV (at 10 mA) |
Min. switching current |
1 mA (24 V) |
Maximum inrush current |
50 mA |
Limiting continuous current |
50 mA |
Interrupting rating (ohmic load) max. |
1.2 W (at 24 V DC) |
Contact side (with destroyed gold layer)
Note |
the following values are applicable if a gold layer is destroyed |
Maximum switching voltage |
250 V AC/DC |
Minimum switching voltage |
5 V (at 100 mA) |
Limiting continuous current |
6 A |
Min. switching current |
10 mA (at 12 V) |
Interrupting rating (ohmic load) max. |
140 W (at 24 V DC) |
|
20 W (at 48 V DC) |
|
18 W (at 60 V DC) |
|
23 W (at 110 V DC) |
|
40 W (at 220 V DC) |
|
1500 VA (for 250 V AC) |
Switching capacity |
2 A (at 24 V, DC13) |
|
0.2 A (at 110 V, DC13) |
|
0.1 A (at 220 V, DC13) |
|
3 A (at 24 V, AC15) |
|
3 A (at 120 V, AC15) |
|
3 A (at 230 V, AC15) |
General
Test voltage |
4 kV AC (50 Hz, 1 min., winding/contact) |
Operating mode |
100% operating factor |
Flammability rating according to UL 94 |
V0 (Housing) |
Mechanical service life |
2x 107 cycles |
Mounting position |
any |
Assembly instructions |
in rows with zero spacing |
Connection data
Connection method |
Screw connection |
Stripping length |
8 mm |
Screw thread |
M3 |
Conductor cross section solid |
0.14 mm² ... 2.5 mm² |
Conductor cross section flexible |
0.14 mm² ... 2.5 mm² |
|
0.2 mm² ... 2.5 mm² (Single ferrule) |
|
2x 0.5 mm² ... 1.5 mm² (TWIN ferrule) |
Conductor cross section AWG |
26 ... 14 |
Torque |
0.6 Nm ... 0.8 Nm |
Standards and Regulations
Designation |
Standards/regulations |
Standards/regulations |
IEC 60664 |
|
EN 50178 |
Pollution degree |
3 |
Overvoltage category |
III |
Conformance/approvals
Designation |
Corrosive gas test |
Identification |
ISA-S71.04. G3 Harsh Group |
|
EN 60068-2-60 |
Environmental Product Compliance
REACh SVHC |
Lead 7439-92-1 |
China RoHS |
Environmentally Friendly Use Period = 50 years |
|
For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration” |
Classifications
ECLASS
ECLASS 10.0.1 |
27371601 |
ECLASS 11.0 |
27371601 |
ECLASS 4.0 |
27371100 |
ECLASS 4.1 |
27371100 |
ECLASS 5.0 |
27371600 |
ECLASS 5.1 |
27371600 |
ECLASS 6.0 |
27371600 |
ECLASS 7.0 |
27371601 |
ECLASS 9.0 |
27371601 |
ETIM
ETIM 2.0 |
EC001437 |
ETIM 3.0 |
EC001437 |
ETIM 4.0 |
EC001437 |
ETIM 6.0 |
EC001437 |
ETIM 7.0 |
EC001437 |
UNSPSC
UNSPSC 6.01 |
30211916 |
UNSPSC 7.0901 |
39121515 |
UNSPSC 11 |
39121515 |
UNSPSC 12.01 |
39121515 |
UNSPSC 13.2 |
39122334 |
UNSPSC 18.0 |
39122334 |
UNSPSC 19.0 |
39122334 |
UNSPSC 20.0 |
39122334 |
UNSPSC 21.0 |
39122334 |
Articles in set
Relay base PLC-BSC- 24DC/21 2966016
6.2 mm PLC basic terminal block with screw connection, without relay or solid-state relay, for mounting on DIN rail NS 35/7,5, 1 changeover contact, input voltage 24 V DC
Single relay REL-MR- 24DC/21AU 2961121
Plug-in miniature power relay, with multi-layer gold contact, 1 changeover contact, input voltage 24 V DC