Cảm biến áp suất -0.1~0.6 MPa 5-40mA NC Dia.6mm Cab.3m switch OFF khi vượt quá mức cài đặt - KITA - KP10B-R6

THÔNG TIN THAM KHẢO

• Danh mục Model sản phẩm KITA

• 

  Các model Cảm biến áp suất Siemens 7MF03xx-xxxxx-xxxx SITRANS P320 Pressure transmitter Gauge pressure

• 

  Các model Cảm biến áp suất Siemens 7MF8010-2xxxx-xxxx SITRANS P Transmitter Compact with clamp-on remote seal

• Xem thêm

Thông tin chi tiết sản phẩm

Cảm biến áp suất -0.1~0.6 MPa 5-40mA NC Dia.6mm Cab.3m switch OFF khi vượt quá mức cài đặt - KITA - KP10B-R6

 

For your safety, please read the following before using

1.Do not user corrosive or flammable gas or liquid with thes product.

2. Please use within the operationg pressure range. Do not apply pressure beyond recommended maximum pressure, permanent damage to the pressure sensor may occur.

3. Do not drop, hit or allow excessive shock. Even if switch body appears undamaged, internal components may be broken and can cause malfunction.

4. Turn power off before connecting wiring. Wrong wiring or short circuit will damage and/or cause malfunction.

5. Do not use in environment containing steam or oil vapor.

6. This product is not explosion-proof rated. Do not use in atmosphere containing flammable or explosive gases.
7. Wiring for pressure switch should avoid power source line and high voltage line. If use in the same circuit, noise may cause malfunction.

8. ESD protection -4..+4KV.

 

Specifications

Specifications	KP10A	KP10B
Set pressure range	-0.1~0.6 Mpa
Withstand pressure	1.5 Mpa
Fluid	Air, Non-corrosive/ Non-flammable gas
Load voltage	12 to 24V DC +/-10%, Ripple (P-P) 10% or less
Load current	5~40mA
Leak current	</= 1mA
Internal voltage drop	</= 5V
Switch output	Present Press . >/= Set Press .: ON	Present Press . >/= Set Press.: OFF
Repeatability	+/- 1% F.S.
Response time	Approx. 1ms
Hysteresis	</= 4% F.S.
Indicator	Indicator Res: ON
Enclosure	IP 40
Temperature characteristic	+/- 3% F.S. of detected pressure (25oC) at temp. Range of 0~50oC
Ambient temp. range	Operation: 0~60oC, Storage: -20~70oC (No condensation or freezing)
Ambient humidity range	Operation/ Storage: 35~85% RH (No condensation)
Vibration	Total amplitude 1.5mm or 10G, 10Hz~55Hz scan for 1 minute, two hours each direction of X, Y and Z
Shock	980m/s2 (100G), 3 times each in direction of X, Y and Z
Piping size	F1 :  R1/8",M5 ; F2 : NPT1/8",M5 ; F3 : G1/8"(BSPP),M5 ; M5 : M5*0.8 ; R4 : Dia.4mm ; R6 : Dia.6mm
Lead wire	Oil-resistance cable, 2 wires (0.18mm2), Dia. 2.6
Weight	Approx. 50g (with 3 meter lead wire

 

Ordering informations

 

Circuit wiring diagram

 

How to set pressure

- Use the Pressure setting trimmer to set "ON" pressure. Rotate clockwise to increase pressure setpont. Rotate counter-clockwise to decrease pressure setpoint

- Use appropriate size screwdriver for the setting trimmers. Gently turn the screwdriver to make adjustments. To prevent damage to the pressure setting trimmer, DO NOT force the trimmer when it comes to a stop.

 

Output type

 

More informations KP10A / KP10B

Features
- Simple installation, plug-in port or thread-in fitting
- Set pressure range：-0.1 ~ 0.6 MPa
- Normally Open / Normally Close


Specifications

Model	KP10A	KP10B
Set Pressure Range	-0.1~0.6 MPa	-0.1~0.6 MPa
Withstand Pressure	1.5 MPa	1.5 MPa
Fluid	Filtered air, Non-corrosive / Non-flammable gas	Filtered air, Non-corrosive / Non-flammable gas
Switch output	Present Press . ≥ Set Press. : ON	Present Press . ≥ Set Press. : OFF

 

- Xem Catalogue Cảm biến áp suất Pressure sensor KITA KP10A KP10B

 

-  Xem Hướng dẫn sử dụng Manual Cảm biến áp suất Pressure sensor KITA KP10A KP10B