Bộ chuyển đổi nhiệt độ Phoenix Contact MACX MCR-T-UI-UP - 2811394

THÔNG TIN THAM KHẢO

• Danh mục Model sản phẩm PHOENIX CONTACT

• 

  Tìm hiểu về điều hòa, lọc nhiểu, khuếch đại, chuyển đổi tín hiệu điều khiển và đo lường MCR

• Xem thêm

Bộ chuyển đổi nhiệt độ Phoenix Contact MACX MCR-T-UI-UP - 2811394

 

Thông số kỹ thuật

Đặc tính

Product type	Temperature transmitter
Product family	MACX Analog
Type	Signal conditioners with SIL and PL Functional Safety
Configuration	DIP switches
	Software
Insulation characteristics
Overvoltage category	II
Pollution degree	2

 

Thông số điện

Electrical isolation	4-way isolation
Maximum power dissipation for nominal condition	1.26 W
Step response (0–99%)	≤ 1.75 s (SIL on)
	1.3 s (SIL off)
Maximum temperature coefficient	0.01 %/K
Electrical isolation Input/output/power supply
Rated insulation voltage	300 Vrms
Test voltage	2.5 kV AC (50 Hz, 60 s)
Insulation	Safe isolation in accordance with IEC/EN 61010-1
Electrical isolation Input/output
Electrical isolation	375 V (Peak value in accordance with IEC/EN 60079-11)
Electrical isolation Input/power supply
Electrical isolation	375 V (Peak value in accordance with IEC/EN 60079-11)
Electrical isolation Input/switching output
Electrical isolation	375 V (Peak value in accordance with IEC/EN 60079-11)
Supply
Nominal supply voltage range	24 V AC/DC ... 230 V AC/DC (50/60 Hz)
Supply voltage range	19.2 V AC/DC ... 253 V AC/DC (24 V AC/DC ... 230 V AC/DC (-20 % ... +10 %, 50/60 Hz))
Power consumption	< 1.5 W

 

Thông số đầu vào

Signal
Number of inputs	1
Input signal	Temperature
	Resistor
	Voltage
Measurement
Sensor types (RTD) that can be used	Pt, Ni, Cu sensors: 2, 3, 4-wire
Sensor types that can be used (TC)	B, E, J, K, N, R, S, T, L, U, CA, DA, A1G, A2G, A3G, MG, LG
Temperature measuring range	-250 °C ... 2500 °C (Range depending on the sensor type)
Linear resistance measuring range	0 Ω ... 50 kΩ
Potentiometer resistance range	0 Ω ... 50 kΩ
Linear mV signal range	-1000 mV ... 1000 mV

 

Thông số đầu ra

Switching: Relay
Configurable/programmable	Yes
Contact type	1 changeover contact
Contact material	AgSnO2, hard gold-plated
Maximum switching voltage	30 V AC (30 V DC)
Max. switching current	0.5 A (30 V AC)
	1 A (30 V DC)
Signal: Current
Number of outputs	1
Configurable/programmable	Yes
Max. voltage output signal	± 11 V
Current output signal	4 mA ... 20 mA (in the case of SIL; further free configuration without SIL)
Max. current output signal	22 mA
Load/output load voltage output	≥ 10 kΩ
Load/output load current output	≤ 600 Ω (20 mA)
Behavior in the event of a sensor error	according to NE 43 or freely configurable

 

Thông số kết nối

Connection method	Screw connection
Stripping length	7 mm
Screw thread	M3
Conductor cross section solid	0.2 mm² ... 2.5 mm²
Conductor cross section flexible	0.2 mm² ... 2.5 mm²
Conductor cross section AWG	24 ... 14

Thông số chống cháy-nổ Ex data

Ex installation (EPL)	Gc
	Div. 2

 

Đèn tín hiệu LED signaling

Error indication

Red LED

 

Kích thước Dimensions

Width	17.5 mm
Height	112.5 mm
Depth	113.7 mm
	114.5 mm (Snapped onto DIN rail NS 35/7,5 in accordance with EN 60715)

 

Thông số cơ học

Flammability rating according to UL 94	V0 (Housing)
Housing material	PA 6.6-FR

 

Thông số điều kiện vận hành Environmental and real-life conditions

Ambient conditions
Ambient temperature (operation)	-20 °C ... 65 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Permissible humidity (operation)	typ. 5 % ... 95 % (non-condensing)
Altitude range (≤ 2000 m)
Altitude	≤ 2000 m (For use at altitudes ≥2000 m above sea level, see data sheet.)
Altitude range (≤ 3000 m)
Height range	> 2000 m ... 3000 m
Ambient temperature (operation)	-20 °C ... 55 °C
Altitude range (≤ 4000 m)
Height range	> 3000 m ... 4000 m
Ambient temperature (operation)	-20 °C ... 50 °C
Altitude range (≤ 5000 m)
Height range	> 4000 m ... 5000 m
Ambient temperature (operation)	-20 °C ... 45 °C

 

Approval data

CE
Certificate	CE-compliant
ATEX
Identification	 II 3 G Ex ec ic nC IIC T4 Gc
Certificate	PxCIF20ATEX2811378
UKCA Ex (UKEX)
Identification	 II 3 G Ex ec ic nC IIC T4 Gc X
Certificate	CML 22UKEX3529X
IECEx
Identification	Ex ec ic nC IIC T4 Gc
Certificate	IECEx IBE 10.0004 X
UL, USA / Canada
Identification	UL 508 Listed
	Class I, Div. 2, Groups A, B, C, D T6
	Class I, Zone 2, Group IIC T6
Shipbuilding approval
Certificate	DNV GL TAA000020C
Safety Integrity Level (SIL, IEC 61508)
Identification	2
Certificate	SEBS-A.150520/17TB
Performance Level (ISO 13849)
Identification	d
INMETRO
Identification	Ex ec ic nC IIC T4 Gc
Certificate	DNV 18.0143 X
EAC Ex
Identification	 2Ex ec ic IIC T4 Gc
Certificate	BY/112 02.01 TP012 103.01 00078
DNV GL data
Temperature	B
Humidity	B
Vibration	A
EMC	A
Enclosure	Required protection according to the Rules shall be provided upon installation on board

 

EMC data

Electromagnetic compatibility	Conformance with EMC directive
Noise emission	EN 61000-6-4
Noise immunity	EN 61000-6-2
Note	When being exposed to interference, there may be minimal deviations.

 

Quy-Chuẩn Standards and regulations

Electrical isolation

4-way isolation

 

Thông số lắp đặt Mounting

Mounting type

DIN rail mounting

 

Thông số thương mại Commercial Data

Item number	2811394
Packing unit	1 pc
Minimum order quantity	1 pc
Note	Made to Order (non-returnable)
Sales Key	C01
Product Key	CK1121
Catalog Page	Page 128 (C-5-2019)
GTIN	4046356520294
Weight per Piece (including packing)	264.2 g
Weight per Piece (excluding packing)	193.9 g
Customs tariff number	85437090
Country of origin	DE

Tham khảo thêm các model khác cùng loại:
Temperature measuring transducer

MACX MCR-T-UI-UP - 2811394

Freely programmable temperature transducer with analog output and 1 limit value relay, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.

Temperature measuring transducer

MINI MCR-SL-PT100-UI-200-NC - 2864370

MCR temperature transducer, configurable, for Pt 100 temperature sensors, with screw-connection, not configured

Temperature measuring transducer

MACX MCR-T-UIREL-UP - 2811378

Freely programmable temperature transducer with analog output and 3 limit value relays, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.

Temperature measuring transducer

MINI MCR-SL-PT100-LP-NC - 2810308

Configurable loop-powered temperature transducer for Pt 100 temperature sensors, configured via DIP switches, with screw connection, not pre-configured

Temperature measuring transducer

MACX MCR-TS-I-OLP - 2908662

Output loop-powered temperature transducer for transmitting up to 2 sensor signals from RTD and TC sensors, as well as from resistance and voltage sensors via 4 mA ... 20 mA. HART, Standard configuration, Safety Integrity Level (SIL, IEC 61508): 2, Systematic Capability: 3, Screw connection

Temperature measuring transducer

MACX MCR-EX-RTD-I - 1050222

Ex i temperature transducer: converts signals from resistance temperature detectors installed in the Ex area and transmits a 0/4 - 20 mA signal to a load in the safe area. Freely programmable. 3-way isolation, SIL, screw connection, standard configuration.

Temperature measuring transducer

MACX MCR-EX-TC-I - 1050233

Ex i temperature transducer: converts signals from thermocouples installed in Ex areas and mV sources and transmits a 0/4…20 mA signal to a load in the safe area. Freely programmable. 3-way isolation, screw connection, SIL.

Temperature measuring transducer

MACX MCR-EX-T-UIREL-UP - 2865751

Programmable temperature transducer with analog output and 3 limit value relays, intrinsically safe signal input, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.

Temperature measuring transducer

MACX MCR-EX-T-UI-UP - 2865654

Freely programmable Ex-i temperature transducer with analog output and 1 limit value relay, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.

Temperature measuring transducer

MACX MCR-T-UI-UP-C - 2811873

Freely programmable temperature transducer with analog output and 1 limit value relay, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.

Temperature measuring transducer

MACX MCR-1TS-I-OLP - 1145192

Output loop-powered temperature transducer for transmitting RTD and TC sensor signals as well as from resistance and voltage sensors via 4 mA ... 20 mA. HART, Standard configuration, Screw connection

Temperature measuring transducer

MACX MCR-EX-RTD-I-C - 1052463

Ex i temperature transducer: converts signals from resistance temperature detectors installed in the Ex area and transmits a 0/4 - 20 mA signal to a load in the safe area. Freely programmable. 3-way isolation, SIL, screw connection, order configuration.

Temperature measuring transducer

MACX MCR-TS-I-OLP-SP - 2908664

Output loop-powered temperature transducer for transmitting up to 2 sensor signals from RTD and TC sensors, as well as from resistance and voltage sensors via 4 mA ... 20 mA. HART, Standard configuration, Safety Integrity Level (SIL, IEC 61508): 2, Systematic Capability: 3, Push-in connection

Temperature measuring transducer

MACX MCR-T-UI-UP-SP-C - 2811970

Freely programmable temperature transducer with analog output and 1 limit value relay, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.

Temperature measuring transducer

MACX MCR-EX-TS-I-OLP-SP - 2908661

Ex i, Output loop-powered temperature transducer for transmitting up to 2 sensor signals from RTD and TC sensors, as well as from resistance and voltage sensors via 4 mA ... 20 mA. HART, Standard configuration, Safety Integrity Level (SIL, IEC 61508): 2, Systematic Capability: 3, Push-in connection

Temperature measuring transducer

MACX MCR-T-UI-UP-SP - 2811860

Freely programmable temperature transducer with analog output and 1 limit value relay, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.

Temperature measuring transducer

MACX MCR-EX-RTD-I-SP - 1050252

Ex i temperature transducer: converts signals from resistance temperature detectors installed in the Ex area and transmits a 0/4 - 20 mA signal to a load in the safe area. Freely programmable, 3-way isolation, SIL, Push-in connection, standard configuration.

Temperature measuring transducer

MACX MCR-RTD-I - 1050192

Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, screw connection, SIL, 3-way electrical isolation, standard configuration.

Temperature measuring transducer

MACX MCR-TC-I - 1050228

Temperature transducer: converts signals from thermocouples and mV sources into 0/4…20 mA signals. Freely programmable, 3-way electrical isolation, screw connection, SIL.

Temperature measuring transducer

MACX MCR-EX-TS-I-OLP - 2908660

Ex i, Output loop-powered temperature transducer for transmitting up to 2 sensor signals from RTD and TC sensors, as well as from resistance and voltage sensors via 4 mA ... 20 mA. HART, Standard configuration, Safety Integrity Level (SIL, IEC 61508): 2, Systematic Capability: 3, Screw connection

Temperature measuring transducer

MACX MCR-EX-T-UI-UP-C - 2811763

Freely programmable Ex-i temperature transducer with analog output and 1 limit value relay, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.

Temperature measuring transducer

MACX MCR-EX-TC-I-C - 1052458

Ex i temperature transducer: converts signals from thermocouples installed in Ex areas and mV sources and transmits a 0/4…20 mA signal to a load in the safe area. Order configuration, freely programmable. 3-way isolation, SIL.

Temperature measuring transducer

MACX MCR-TS-I-OLP-C - 1012249

Output loop-powered temperature transducer for transmitting up to 2 sensor signals from RTD and TC sensors, as well as from resistance and voltage sensors via 4 mA ... 20 mA. HART, Order configuration, Safety Integrity Level (SIL, IEC 61508): 2, Systematic Capability: 3, Screw connection

Temperature measuring transducer

MACX MCR-T-UIREL-UP-SP - 2811828

Freely programmable temperature transducer with analog output and 3 limit value relays, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.

Temperature measuring transducer

MACX MCR-1TS-I-OLP-SP - 1145196

Output loop-powered temperature transducer for transmitting RTD and TC sensor signals as well as from resistance and voltage sensors via 4 mA ... 20 mA. HART, Standard configuration, Push-in connection

Temperature measuring transducer

MACX MCR-TC-I-C - 1052459

Temperature transducer: converts signals from thermocouples and mV sources into 0/4…20 mA signals. Order configuration, freely programmable, 3-way electrical isolation, screw connection, SIL.

Temperature measuring transducer

MACX MCR-EX-T-UIREL-UP-SP - 2924799

Programmable temperature transducer with analog output and 3 limit value relays, intrinsically safe signal input, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.

Temperature measuring transducer

MACX MCR-RTD-I-SP - 1050201

Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, Push-in connection, SIL, 3-way electrical isolation, standard configuration.

Temperature measuring transducer

MACX MCR-EX-1TS-I-OLP-SP - 1145207

Ex i, Output loop-powered temperature transducer for transmitting RTD and TC sensor signals as well as from resistance and voltage sensors via 4 mA ... 20 mA. HART, Standard configuration, Push-in connection

Temperature measuring transducer

MACX MCR-EX-T-UIREL-UP-SP-C - 2924809

Programmable temperature transducer with analog output and 3 limit value relays, intrinsically safe signal input, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.

Temperature measuring transducer

MACX MCR-RTD-I-C - 1052472

Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, screw connection, SIL, 3-way electrical isolation, order configuration.

Temperature measuring transducer

MACX MCR-RTD-I-SP-C - 1052464

Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, Push-in connection, SIL, 3-way electrical isolation, order configuration.

Temperature measuring transducer

MACX MCR-EX-T-UIREL-UP-C - 2865722

Programmable temperature transducer with analog output and 3 limit value relays, intrinsically safe signal input, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.

Temperature measuring transducer

MACX MCR-T-UIREL-UP-SP-C - 2811831

Freely programmable temperature transducer with analog output and 3 limit value relays, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.

Temperature measuring transducer

MACX MCR-EX-RTD-I-SP-C - 1052652

Ex i temperature transducer: converts signals from resistance temperature detectors installed in the Ex area and transmits a 0/4 - 20 mA signal to a load in the safe area. Freely programmable, 3-way isolation, SIL, Push-in connection, order configuration.

Temperature measuring transducer

MACX MCR-EX-1TS-I-OLP - 1145365

Ex i, Output loop-powered temperature transducer for transmitting RTD and TC sensor signals as well as from resistance and voltage sensors via 4 mA ... 20 mA. HART, Standard configuration, Screw connection

Temperature measuring transducer

MACX MCR-EX-T-UI-UP-SP-C - 2924692

Freely programmable Ex-i temperature transducer with analog output and 1 limit value relay, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.

Temperature measuring transducer

MACX MCR-EX-TS-I-OLP-C - 1012248

Ex i, Output loop-powered temperature transducer for transmitting up to 2 sensor signals from RTD and TC sensors, as well as from resistance and voltage sensors via 4 mA ... 20 mA. HART, Order configuration, Safety Integrity Level (SIL, IEC 61508): 2, Systematic Capability: 3, Screw connection

Temperature measuring transducer

MACX MCR-EX-T-UI-UP-SP - 2924689

Programmable Ex-i temperature transducer with analog output and 1 limit value relay, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.

Temperature measuring transducer

MACX MCR-T-UIREL-UP-C - 2811514

Freely programmable temperature transducer with analog output and 3 limit value relays, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.

Thermocouple measuring transducer

MINI MCR-TC-UI-NC - 2902851

Configurable temperature transducer for the connection of thermocouples. Can be configured via DIP switches or, with extended functionality, using the software. Screw connection, standard configuration.

Thermocouple measuring transducer

MINI MCR-2-TC-UI - 2902055

Configurable temperature transducer with plug-in connection technology for connecting thermocouples. Configurable via DIP switch or software. Screw connection technology, standard configuration

Thermocouple measuring transducer

MINI MCR-2-TC-UI-PT - 2905249

Configurable temperature transducer with plug-in connection technology for connecting thermocouples. Configurable via DIP switch or software. Push-in connection technology, standard configuration

Resistance thermometer measuring transducer

MINI MCR-SL-PT100-UI-NC - 2864273

MCR temperature transducer for Pt 100 temperature sensors, configured via DIP switch, with screw connection, not pre-configured

Resistance thermometer measuring transducer

MINI MCR-2-RTD-UI - 2902049

Configurable temperature transducer with plug-in connection technology for connecting 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Configurable via DIP switch or software. Screw connection technology, standard configuration
Customizable

Thermocouple measuring transducer

MINI MCR-2-TC-UI-C - 2902053

Configurable temperature transducer with plug-in connection technology for connecting thermocouples. Configurable via DIP switch or software. Screw connection technology, order configuration

Resistance thermometer measuring transducer

MINI MCR-RTD-UI-NC - 2902849

Configurable temperature transducer for the connection of 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Can be configured via DIP switches or, with extended functionality, using the software. Screw connection, standard configuration.

Resistance thermometer measuring transducer

MINI MCR-2-RTD-UI-PT - 2902052

Configurable temperature transducer with plug-in connection technology for connecting 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Configurable via DIP switch or software. push-in connection technology, standard configuration

Thermocouple measuring transducer

MINI MCR-2-TC-UI-PT-C - 2905248

Configurable temperature transducer with plug-in connection technology for connecting thermocouples. Configurable via DIP switch or software. Push-in connection technology, order configuration

Resistance thermometer measuring transducer

MINI MCR-2-RTD-UI-PT-C - 2902051

Configurable temperature transducer with plug-in connection technology for connecting 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Configurable via DIP switch or software. push-in connection technology, order configuration

Resistance thermometer measuring transducer

MINI MCR-2-RTD-UI-C - 2902048

Configurable temperature transducer with plug-in connection technology for connecting 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Configurable via DIP switch or software. Screw connection technology, order configuration

Temperature module

AXL F UTH4 1H - 2688598

Axioline F, Temperature recording module, Analog inputs: 4 (4 inputs for thermocouples or linear voltage, plus 1 input -5 V to +5 V), connection technology: 2-conductor (shielded, twisted pair), transmission speed in the local bus: 100 Mbps, degree of protection: IP20, including bus base module and Axioline F connectors

Temperature module

AXL F UTH8 1F - 2688417

Axioline F, Temperature recording module, Analog inputs: 8 (8 inputs for thermocouples or linear voltage, plus 1 input -5 V to +5 V), connection technology: 2-conductor (shielded, twisted pair), transmission speed in the local bus: 100 Mbps, degree of protection: IP20, including bus base module and Axioline F connectors

Temperature measuring transducer

MINI MCR-BL-PT100-I-LP-NC - 2810609

Loop-powered MCR temperature transducer, configurable, for Pt 100 temperature sensors for the measuring range -150°C ... 300 °C, screw connection

Temperature measuring transducer

MINI MCR-BL-PT100-I-NC - 2810489

MCR temperature transducer, configurable, for Pt 100 temperature sensors for the measuring range -50°C ... 200 °C, screw connection

Temperature module

AXL F UTH8 XC 1F - 2702464

Axioline F, Temperature recording module, Analog inputs: 8 (8 inputs for thermocouples or linear voltage, plus 1 input -5 V to +5 V), connection technology: 2-conductor (shielded, twisted pair), transmission speed in the local bus: 100 Mbps, Extreme conditions version, degree of protection: IP20, including bus base module and Axioline F connectors

Temperature measuring transducer

MCR-FL-T-LP-I - 2864561

MCR temperature measuring transducer: programmable, loop-powered, for resistance thermometers, thermocouples, resistance-type sensors and voltage sensors.

Temperature measuring transducer

MCR-SL-PT100-LP-I - 2864558

MCR temperature transducers: programmable loop-powered temperature transducers for Pt 100 resistance thermometers
No longer in product range
View replacement product 1145192

Temperature measuring transducer

MACX MCR-EX-SL-TC-I-NC - 2865586

Ex i temperature transducer: converts signals from thermocouples installed in the Ex area and mV sources and transmits a 0/4 - 20 mA signal to a load in the safe area. Freely programmable, 3-way isolation. Replacement item: 1050233 MACX MCR-EX-TC-I.
No longer in product range
View replacement product 1050233

Temperature measuring transducer

MINI MCR-SL-PT100-LP-NC-SP - 2810395

Configurable loop-powered temperature transducer for Pt 100 temperature sensors, configured via DIP switches, with spring-cage connection, not pre-configured. Replacement part: 2810308 MINI MCR-SL-PT100-LP-NC.
No longer in product range
View replacement product 2810308

Temperature measuring transducer

MCR-FL-T-LP-I-EX - 2864574

MCR head-mounted temperature transducers: Programmable loop-powered temperature transducers. Resistance thermometers, thermocouples, resistance-type sensors and voltage sensors.
No longer in product range

Temperature measuring transducer

MACX MCR-EX-SL-RTD-I-SP-NC - 2924168

Ex i temperature transducer: converts signals from resistance temperature detectors installed in the Ex area and transmits a 0/4 - 20 mA signal to a load in the safe area. Freely programmable, spring-cage terminal blocks. Replacement item: 1050252 MACX MCR-EX-RTD-I-SP.
No longer in product range
View replacement product 1050252

Temperature measuring transducer

MACX MCR-EX-SL-RTD-I-NC - 2865573

Ex i temperature transducer: converts signals from resistance temperature detectors installed in the Ex area and transmits a 0/4 - 20 mA signal to a load in the safe area. Freely programmable, 3-way isolation. Replacement item: 1050222 MACX MCR-EX-RTD-I.
No longer in product range
View replacement product 1050222

Temperature measuring transducer

MINI MCR-SL-PT100-UI-200 - 2864309

MCR temperature transducer, can be configured, for Pt 100 temperature sensors, with screw connection, order configuration. Replacement part: 2902048 MINI MCR-2-RTD-UI-C.
No longer in product range
View replacement product 2902048

Temperature measuring transducer

MACX PL-T-UIREL-UP-SP - 2904903

Freely programmable temperature transducer with analog output and 3 limit value relays, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, spring-cage connection, PLd. Replacement part: 2811828 MACX MCR-T-UIREL-UP-SP.
No longer in product range
View replacement product 2811828

Temperature measuring transducer

MCR-FL-TS-LP-I-EX-400 - 2904872

Measurement and control temperature transducers, resistance thermometers, thermocouples, resistance-type sensors, and voltage sensors. Replacement part: 1012249 MACX MCR-EX-TS-I-OLP-C.
No longer in product range
View replacement product 1012249

Temperature measuring transducer

MCR-FL-TS-LP-I-EX - 2864587

Measurement and control temperature transducers, resistance thermometers, thermocouples, resistance-type sensors, and voltage sensors. Replacement part: 2908660 MACX MCR-EX-TS-I-OLP.
No longer in product range
View replacement product 2908660

Temperature measuring transducer

MCR-T-UI-E-NC - 2814126

MCR-T module, programmable temperature transducer, unconfigured, for thermocouple sensors and resistance temperature detectors, in 2-, 3- or 4-conductor technology, with electrical isolation between input/output and input/auxiliary power
No longer in product range
View replacement product 2811394

Temperature measuring transducer

MACX PL-T-UIREL-UP - 2904901

Freely programmable temperature transducer with analog output and 3 limit value relays, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, screw connection, PLd. Replacement part: 2811378 MACX MCR-T-UIREL-UP.
No longer in product range
View replacement product 2811378

Temperature measuring transducer

MACX PL-EX-T-UIREL-UP-SP - 2904912

Programmable temperature transducer with analog output and 3 limit value relays, intrinsically safe signal inputs, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, spring-cage connection, PLd. Replacement part: 2924799 MACX MCR-EX-T-UIREL-UP-SP.
No longer in product range
View replacement product 2924799

Temperature measuring transducer

MCR-T-UI-NC - 2814100

MCR-T module, programmable temperature transducer, unconfigured, for thermocouple sensors and resistance temperature detectors, in 2-, 3- or 4-conductor technology
No longer in product range
View replacement product 2811394

Temperature measuring transducer

MACX PL-EX-T-UIREL-UP - 2904910

Programmable temperature transducer with analog output and 3 limit value relays, intrinsically safe signal inputs, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, screw connection, PLd. Replacement part: 2865751 MACX MCR-EX-T-UIREL-UP.
No longer in product range
View replacement product 2865751

Temperature measuring transducer

MACX MCR-EX-SL-RTD-I - 2865939

Ex i temperature transducer: converts signals from resistance temperature detectors installed in the Ex area and transmits a 0/4 - 20 mA signal to a load in the safe area. Freely programmable. 3-way isolation, screw connection, order configuration. Replacement item: 1052463 MACX MCR-EX-RTD-I-C.
No longer in product range
View replacement product 1052463

Temperature measuring transducer

MCR-FL-TS-LP-EX/-+200 - 2905712

Measurement and control temperature transducers, resistance thermometers, thermocouples, resistance-type sensors, and voltage sensors. Replacement part: 1012249 MACX MCR-EX-TS-I-OLP-C.
No longer in product range
View replacement product 1012249

Temperature measuring transducer

MINI MCR-SL-PT100-LP - 2810298

Loop-powered temperature transducer for Pt 100 temperature sensors, configured via DIP switches, with screw connection, pre-configured (please observe the order key). Replacement part: 2810308 MINI MCR-SL-PT100-LP-NC.
No longer in product range
View replacement product 2810308

Temperature measuring transducer

MINI MCR-SL-PT100-UI-200-SP-NC - 2864202

MCR temperature transducer, configurable, for Pt 100 temperature sensors, with spring-cage connection, not configured. Replacement part: 2902052 MINI MCR-2-RTD-UI-PT.
No longer in product range
View replacement product 2902052

Temperature measuring transducer

MACX MCR-EX-SL-TC-I - 2865942

Ex i temperature transducer: converts signals from thermocouples installed in the Ex area and mV sources and transmits a 0/4 - 20 mA signal to a load in the safe area. Freely programmable, custom-configured. Replacement item: 1052458 MACX MCR-EX-TC-I-C.
No longer in product range
View replacement product 1052458

Temperature measuring transducer

MACX MCR-SL-TC-I - 2924333

Temperature transducer, converts signals from thermocouples and linear mV sources into 0/4 – 20 mA analog signals. Freely programmable, 3-way electrical isolation, custom-configured. Replacement item: 1052459 MACX MCR-TC-I-C.
No longer in product range
View replacement product 1052459

Temperature measuring transducer

MACX MCR-SL-RTD-I - 2865065

Temperature transducer, converts signals from resistance temperature detectors and resistors into 0/4 - 20 mA analog signals. Freely programmable, 3-way electrical isolation, custom-configured. Replacement item: 1052472 MACX MCR-RTD-I-C.
No longer in product range
View replacement product 1052472

Temperature measuring transducer

MACX MCR-SL-TC-I-NC - 2924346

Temperature transducer, converts signals from thermocouples and linear mV sources into 0/4 - 20 mA analog signals. Freely programmable, 3-way electrical isolation, custom-configured. Replacement item: 1050228 MACX MCR-TC-I.
No longer in product range
View replacement product 1050228

Temperature measuring transducer

MCR-FL-TS-LP-I-EX-200 - 2904871

Measurement and control temperature transducers, resistance thermometers, thermocouples, resistance-type sensors, and voltage sensors. Replacement part: 1012249 MACX MCR-EX-TS-I-OLP-C.
No longer in product range
View replacement product 1012249

Temperature measuring transducer

MINI MCR-SL-PT100-UI-200-SP - 2864192

MCR temperature transducer, can be configured, for Pt 100 temperature sensors, with spring-cage connection, order configuration. Replacement part: 2902051 MINI MCR-2-RTD-UI-PT-C.
No longer in product range
View replacement product 2902051

Temperature measuring transducer

MACX MCR-EX-SL-RTD-I-SP - 2924142

Ex i temperature transducer: converts signals from resistance temperature detectors installed in the Ex area and transmits a 0/4 - 20 mA signal to a load in the safe area. Freely programmable, spring-cage terminal blocks, custom-configured. Replacement item: 1052652 MACX MCR-EX-RTD-I-SP-C.
No longer in product range
View replacement product 1052652

Temperature measuring transducer

MACX MCR-SL-RTD-I-SP - 2924317

Temperature transducer, converts signals from resistance temperature detectors and resistors into 0/4 – 20 mA analog signals. Freely programmable, 3-way electrical isolation, custom-configured. Replacement item: 1052464 MACX MCR-RTD-I-SP-C.
No longer in product range
View replacement product 1052464

Temperature measuring transducer

MCR-T-UI-E - 2814113

MCR-T module, programmable temperature transducer, configured, for thermocouple sensors and resistance temperature detectors, in 2-, 3- or 4-conductor technology, with electrical isolation between input/output and input/auxiliary power
No longer in product range
View replacement product 2811873

Temperature measuring transducer

MACX MCR-SL-RTD-I-SP-NC - 2924320

Temperature transducer, converts signals from resistance temperature detectors and resistors into 0/4 - 20 mA analog signals. Freely programmable, 3-way electrical isolation. Replacement item: 1050201 MACX MCR-RTD-I-SP.
No longer in product range
View replacement product 1050201

Temperature measuring transducer

MACX MCR-SL-RTD-I-NC - 2865078

Temperature transducer, converts signals from resistance temperature detectors and resistors into 0/4 – 20 mA analog signals. Freely programmable, 3-way electrical isolation. Replacement item: 1050192 MACX MCR-RTD-I.
No longer in product range
View replacement product 1050192

Temperature measuring transducer

MINI MCR-SL-PT100-LP-SP - 2810382

Loop-powered temperature transducer for Pt 100 temperature sensors, configured via DIP switches, with spring-cage connection, pre-configured (please observe the order key). Replacement part: 2810308 MINI MCR-SL-PT100-LP-NC.
No longer in product range
View replacement product 2810308

Temperature measuring transducer

MCR-FL-TS-LP-I-EX-800 - 2904873

Measurement and control temperature transducers, resistance thermometers, thermocouples, resistance-type sensors, and voltage sensors. Replacement part: 1012249 MACX MCR-EX-TS-I-OLP-C.
No longer in product range
View replacement product 1012249

Temperature measuring transducer

MCR-T-UI - 2814090

MCR-T module, programmable temperature transducer, configured, for thermocouple sensors and resistance temperature detectors, in 2-, 3- or 4-conductor technology
No longer in product range
View replacement product 2811873

Thermocouple measuring transducer

MCR-TE-J-K-I - 2810544

MCR temperature measuring transducer, for thermocouples type J, K input: 0 - 400°C, 0 - 800°C, 0 - 1000°C, 0 - 1200°C, output signal 0(4)...20 mA
No longer in product range
View replacement product 2864448

Thermocouple measuring transducer

MCR-TE-JK-U-E - 2810515

MCR temperature measuring transducer, for thermocouples type J, K input: 0 - 400°C, 0 - 800°C, 0 - 1000°C, 0 - 1200°C, input electrically isolated, output signal 0..10 V
No longer in product range
View replacement product 2905248

Thermocouple measuring transducer

MCR-TE-JK-U - 2810531

MCR temperature measuring transducer, for thermocouples type J, K input: 0 - 400°C, 0 - 800°C, 0 - 1000°C, 0 - 1200°C, output signal 0 V ... 10 V
No longer in product range
View replacement product 2864448

Thermocouple measuring transducer

MCR-TE-JK-I-E - 2810528

MCR temperature measuring transducer, for thermocouples type J, K input: 0 - 400°C, 0 - 800°C, 0 - 1000°C, 0 - 1200°C, input electrically isolated, output signal 0(4)...20 mA
No longer in product range
View replacement product 2864448

Thermocouple measuring transducer

MCR-TE-J-K-I-E-NC - 2810560

Temperature transducers for thermocouples type J, K, configurable via DIP switch, input: 0...400 °C, 0...800 °C, 0...1000 °C, 0...1200 °C, input electrically isolated, output signal 0(4)...20 mA
No longer in product range
View replacement product 2902851

Thermocouple measuring transducer

MCR-TE-J-K-I-NC - 2810586

Temperature transducers for thermocouples type J, K, configurable via DIP switch, input: 0...400 °C, 0...800 °C, 0...1000 °C, 0...1200 °C, output signal 0(4)...20 mA
No longer in product range
View replacement product 2902851

Thermocouple measuring transducer

MCR-TE-J-K-U-NC - 2810573

Temperature transducers, for thermocouples type J, K, configurable via DIP switch, input: 0...400 °C, 0...800 °C, 0...1000 °C, 0...1200 °C, output signal 0..10 V
No longer in product range
View replacement product 2902851

Thermocouple measuring transducer

MCR-TE-J-K-U-E-NC - 2810557

Temperature transducers, for thermocouples type J, K, configurable via DIP switch, input: 0...400 °C, 0...800 °C, 0...1000 °C, 0...1200 °C, input electrically isolated, output signal 0..10 V
No longer in product range
View replacement product 2902851

Signal converter

PI-EX-RTD-I-NC - 2835590

Ex i temperature measuring transducer: Converts signals from Pt 100 resistance thermometers installed in Ex areas and transmits a 4 - 20 mA signal to a load in a safe area. Freely programmable. Galvanic 3-way isolation. Configurable.
No longer in product range
View replacement product 2865311

Thermocouple measuring transducer

MINI MCR-SL-TC-UI - 2864448

MCR temperature transducer for thermocouples, can be configured via DIP switches, with screw connection, order configuration
No longer in product range

Thermocouple measuring transducer

MINI MCR-SL-TC-UI-NC - 2864299

MCR temperature transducer for thermocouples, can be configured via DIP switches, with screw connection, standard configuration
No longer in product range
View replacement product 2902851

Resistance thermometer measuring transducer

MINI MCR-RTD-UI-SP-NC - 2902850

Temperature transducer for the connection of 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Configurable via DIP switch or software. Spring-cage connection, standard configuration. Replacement part: 2902052 MINI MCR-2-RTD-UI-PT.
No longer in product range
View replacement product 2902052

Resistance thermometer measuring transducer

MCR-PT100-U-DC - 2810311

MCR temperature transducer, for Pt 100, 2-, 3-, 4-conductor technology; input: 0 ... 100°C, 0 ... 150°C, 0 ... 200°C, 0 ... 300°C, -50 ... +50°C, -50 ... 100°C, -50 ... 150°C, -50 ... 250°C, output signal: 0 ... 10 V, electrically isolated auxiliary power
No longer in product range
View replacement product 2864435

Resistance thermometer measuring transducer

MCR-PT100-I - 2810353

MCR temperature transducer, for Pt 100, 2-, 3-, 4-conductor technology; input: 0 ... 100°C, 0 ... 150°C, 0 ... 200°C, 0 ... 300°C, -50 ... +50°C, -50 ... 100°C, -50 ... 150°C, -50 ... 250°C, output signal: 0(4) ... 20 mA
No longer in product range
View replacement product 2864435

Resistance thermometer measuring transducer

MCR-SL-PT100-U-DC-24 - 2814870

MCR temperature transducer, for Pt 100, 2-, 3-, 4-conductor technology, input: -100°C ... 600°C, output signal: 0 V ... 10 V
No longer in product range
View replacement product 2864435

Resistance thermometer measuring transducer

MCR-PT100-U - 2810340

MCR temperature transducer, for Pt 100, 2-, 3-, 4-conductor technology; input: 0 ... 100°C, 0 ... 150°C, 0 ... 200°C, 0 ... 300°C -50 ... +50°C, -50 ... 100°C, -50 ... 150°C, -50 ... 250°C, output signal: 0 ... 10 V
No longer in product range
View replacement product 2864435

Resistance thermometer measuring transducer

MCR-PT100-I-DC - 2810337

MCR temperature transducer, for Pt 100, 2-, 3-, 4-conductor technology; input: 0 ... 100°C, 0 ... 150°C, 0 ... 200°C, 0 ... 300°C, -50 ... +50°C, -50 ... 100°C, -50 ... 150°C, -50 ... 250°C, output signal: 0(4) ... 20 mA, electrically isolated auxiliary power
No longer in product range
View replacement product 2864435

Resistance thermometer measuring transducer

MINI MCR-SL-PT100-UI - 2864435

MCR temperature transducer for Pt 100 temperature sensors, configured via DIP switches, with screw connection, pre-configured (please observe the order key). Replacement part: 2902048 MINI MCR-2-RTD-UI-C.
No longer in product range
View replacement product 2902048

Resistance thermometer measuring transducer

MCR-SL-PT100-I-DC-24 - 2814883

MCR temperature transducer, for Pt 100, 2-, 3-, 4-conductor technology, input: -100°C ... 600°C, output signal: 0(4) mA ... 20 mA
No longer in product range
View replacement product 2864435

Resistance thermometer measuring transducer

MCR-PT100-I-DC-NC - 2810447

Pt 100 temperature transducer, configurable via DIP switch, selection between 2, 3, 4-conductor technology; output signal 0(4)...20 mA, auxiliary voltage electrically isolated
No longer in product range
View replacement product 2864273

Resistance thermometer measuring transducer

MCR-PT100-I-NC - 2810421

Pt 100 temperature transducer, configurable via DIP switch, selection between 2, 3, 4-conductor technology; input: 0...100 °C, 0...150 °C, 0...200 °C, 0...300 °C, -50...+50 °C, -50...100 °C, -50...150 °C, -50...250 °C, output signal 0(4)...20 mA
No longer in product range
View replacement product 2864273

Resistance thermometer measuring transducer

MCR-PT100-U-NC - 2810418

Pt 100 temperature transducer, configurable via DIP switch, selection between 2, 3, 4-conductor technology; input: 0...100 °C, 0...150 °C, 0...200 °C, 0...300 °C, -50...+50 °C, -50...100 °C, -50...150 °C, -50...250 °C, output signal 0...10 V
No longer in product range
View replacement product 2864273

Resistance thermometer measuring transducer

MCR-PT100-U-DC-NC - 2810434

Pt 100 temperature transducer, configurable via DIP switch, selection between 2, 3, 4-conductor technology; output signal 0...10 V, auxiliary voltage electrically isolated
No longer in product range
View replacement product 2864273

Resistance thermometer measuring transducer

MINI MCR-SL-PT100-UI-SP-NC - 2864286

Measurement and control temperature transducer for Pt 100 temperature sensors, configured via DIP switches, with spring-cage connection, not pre-configured. Replacement part: 2902052 MINI MCR-2-RTD-UI-PT.
No longer in product range
View replacement product 2902052

Resistance thermometer measuring transducer

MINI MCR-SL-PT100-UI-SP - 2864736

Measurement and control temperature transducer for Pt 100 temperature sensors, configured via DIP switches, with spring-cage connection, pre-configured. Replacement part: 2902051 MINI MCR-2-RTD-UI-PT-C.
No longer in product range
View replacement product 2902051

I/O module

AXL UTH 8-ME - 2688420

Axioline temperature module, 8 inputs for connection of thermocouple sensors (electronics modules as replacement for 2688417 AXL UTH 8 product)
No longer in product range
View replacement product 2688417