Bộ chuyển đổi tín hiệu nhiệt Phoenix Contact MINI MCR-2-RTD-UI-PT - 2902052

Bộ chuyển đổi tín hiệu nhiệt Phoenix Contact MINI MCR-2-RTD-UI-PT - 2902052

839
Nhà sản xuất:

Phoenix Contact

;   

Xuất xứ: Germany

Giá sỉ:

Giá tốt nhất xem...0909186879 dienelectrics@gmail.com

Khuyến mãi:Có Discount
Bảo hành:12 Tháng (Chính hãng)
Thanh toán:C.O.D / Bảo lãnh TT / Link hoạt
Vận chuyển:Miễn phí Tp.HCM, vùng lân cận
Thông tin nổi bật

Bộ chuyển đổi tín hiệu nhiệt Phoenix Contact MINI MCR-2-RTD-UI-PT - 2902052

Electrical number: 4311207

Configurable temperature transducer with plug-in connection technology for connecting 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Configurable via DIP switch or software. push-in connection technology, standard configuration
 

 

Mô tả

Bộ chuyển đổi nhiệt độ cách ly 3 chiều có thể định cấu hình với công nghệ kết nối plug-in. Thiết bị phù hợp để kết nối các nhiệt kế điện trở và cảm biến loại điện trở từ xa với công nghệ kết nối 2, 3, 4 dây dẫn. Các giá trị đo được chuyển đổi thành tín hiệu dòng điện hoặc điện áp tuyến tính và có thể điều chỉnh tự do. Bạn có thể định cấu hình thiết bị bằng một trong các giải pháp phần mềm miễn phí. Cài đặt mặc định cũng có thể được thực hiện trực tiếp trên thiết bị bằng cách sử dụng công tắc DIP (xem bảng cấu hình). Đầu dò đo hỗ trợ giám sát lỗi và giao tiếp NFC/ Configurable, 3-way isolated temperature transducer with plug-in connection technology. The device is suitable for the connection of resistance thermometers and remote resistance-type sensors with 2, 3, and 4-conductor connection technology. The measured values are converted into a linear and freely adjustable current or voltage signal. You can configure the device using one of the free software solutions. Default settings can also be made directly on the device by simply using the DIP switches (see configuration table). The measuring transducer supports fault monitoring and NFC communication.

 

Thông số kỹ thuật

Notes

Utilization restriction
EMC note EMC: class A product, see manufacturer's declaration in the download area
 

Product properties

Product type Temperature transmitter
Product family MINI Analog Pro
Type Signal conditioner
Configuration DIP switches
Software
App
Insulation characteristics
Overvoltage category II
Pollution degree 2
 

Electrical properties

Electrical isolation 3-way isolation
Protective circuit Transient protection
Step response (0–99%) 200 ms (2-conductor)
500 ms (3-conductor)
500 ms (4-conductor)
Maximum temperature coefficient 0.01 %/K
Transmission error resistance-type sensor 2 Ω
Transmission error resistance thermometer 0.1 % * 350 K / set measuring range; 0.1 % > 350 K (Pt/Ni)
0.3 % * 200 K / set measuring range; 0.3 % > 200 K (Cu)
Electrical isolation Input/output/power supply
Rated insulation voltage 300 Vrms
Test voltage 3 kV AC (50 Hz, 60 s)
Insulation Reinforced insulation according to IEC/EN 61010-1
Supply
Supply voltage range 9.6 V DC ... 30 V DC (The DIN rail connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, item no. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail in accordance with EN 60715)
Typical current consumption 32 mA (24 V DC)
63 mA (12 V DC)
Power consumption ≤ 850 mW (at IOUT = 20 mA, 9.6 V DC, 600 Ω load)
 

Input data

Signal
Number of inputs 1
Measurement
Number of inputs 1
Configurable/programmable Yes
Sensor types (RTD) that can be used Pt, Ni, Cu sensors
Temperature measuring range -200 °C ... 850 °C (Range depends on sensor type, range can be set freely via software or in increments from -150°C to 850°C via DIP switches)
Temperature measuring range ≥ 20 K
Sensor input current approx. 200 µA
Max. permissible overall conductor resistance ≤ 25 Ω (Per line, RTD in 3- or 4-conductor technology)
≤ 50 Ω (adjustable, RTD in 2-conductor technology)
Linear resistance measuring range 0 Ω ... 4000 Ω (Minimum measuring span: 10% of the selected measuring range)
Connection technology 2-, 3-, 4-conductor
 

Output data

Signal: Voltage/current
Number of outputs 1
Configurable/programmable Yes
Voltage output signal 0 V ... 5 V (via DIP switch)
1 V ... 5 V (via DIP switch)
0 V ... 10 V (via DIP switch)
10 V ... 0 V (via DIP switch)
0 V ... 10.5 V (can be set via software)
Max. voltage output signal approx. 12.3 V
Non-load voltage < 17.5 V
Current output signal 0 mA ... 20 mA (via DIP switch)
4 mA ... 20 mA (via DIP switch)
20 mA ... 0 mA (via DIP switch)
20 mA ... 4 mA (via DIP switch)
0 mA ... 21 mA (can be set via software)
Max. current output signal 24.6 mA
Short-circuit current < 31.5 mA
Load/output load voltage output ≥ 10 kΩ
Load/output load current output ≤ 600 Ω (at 20 mA)
Ripple < 10 mVrms
< 10 mVrms (at 600 Ω)
Resolution, outputs (voltage) 1 mV
Resolution, outputs (current) 2 µA
Behavior in the event of a sensor error configurable
 

Connection data

Connection method Push-in connection
Stripping length 10 mm
Conductor cross section rigid 0.2 mm² ... 2.5 mm² (with ferrule)
0.14 mm² ... 2.5 mm² (without ferrule)
Conductor cross section flexible 0.14 mm² ... 2.5 mm²
Conductor cross section AWG 24 ... 12 (flexible)
 

Ex data

Ex installation (EPL) Gc
Div. 2
 

Interfaces

Data: IFS interface
Connection method Micro USB type B
 

Signaling

Status display Green LED (supply voltage)
Error indication Red LED
 

Dimensions

Width 6.2 mm
Height 109.81 mm
Depth 119.2 mm
 

Material specifications

Fire protection for rail vehicles (DIN EN 45545-2) R22 HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R23 HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R24 HL 1 - HL 2
Housing material PBT
 

Environmental and real-life conditions

Ambient conditions
Degree of protection IP20 (not assessed by UL)
Ambient temperature (operation) -40 °C ... 70 °C
Ambient temperature (storage/transport) -40 °C ... 85 °C
Altitude ≤ 2000 m
Permissible humidity (operation) 5 % ... 95 % (non-condensing)
 

Approvals

CE
Certificate CE-compliant
ATEX
Identification  II 3 G Ex ec IIC T4 Gc
Certificate BVS 20 ATEX E 024 X
UKCA Ex (UKEX)
Identification  II 3 G Ex ec IIC T4 Gc
Certificate PxCIF21UKEX2902049X
IECEx
Identification Ex ec IIC T4 Gc
Certificate IECEx BVS 20.0017X
UL, USA/Canada
Identification UL 508 Listed
Class I, Div. 2, Groups A, B, C, D T6
Class I, Zone 2, Group IIC T6
Shipbuilding approval
Certificate DNV GL TAA00002UA
EAC Ex
Identification  2Ex ec IIC T4 Gc
Certificate BY/112 02.01 TP012 103.01 00079
DNV GL data
Temperature B
Humidity B
Vibration A
EMC A
Enclosure Required protection according to the Rules shall be provided upon installation on board
 

EMC data

Noise immunity EN 61000-6-2
Note When being exposed to interference, there may be minimal deviations.
Electromagnetic compatibility Conformance with EMC directive
Noise emission EN 61000-6-4
Electrostatic discharge
Standards/regulations EN 61000-4-2
Electrostatic discharge
Comments Safety measures must be taken to prevent electrostatic discharge.
Electromagnetic HF field
Designation Electromagnetic RF field
Standards/regulations EN 61000-4-3
Typical deviation from the measuring range final value 0.06 %
Fast transients (burst)
Designation Fast transients (burst)
Standards/regulations EN 61000-4-4
Typical deviation from the measuring range final value 0.1 %
Surge current load (surge)
Standards/regulations EN 61000-4-5
Conducted interference
Designation Conducted interferences
Standards/regulations EN 61000-4-6
Typical deviation from the measuring range final value 0.07 %
 

Standards and regulations

Electrical isolation 3-way isolation
 

Mounting

Mounting type DIN rail mounting
Assembly instructions The DIN rail connector can be used for bridging the supply voltage. It can be snapped onto a 35 mm EN 60715 DIN rail.
Mounting position any
 

Commercial data

Item number 2902052
Packing unit 1 pc
Minimum order quantity 1 pc
Sales key 31BCK
Product key CK1421
Catalog page Page 82 (C-5-2019)
GTIN 4046356652094
Weight per piece (including packing) 118.1 g
Weight per piece (excluding packing) 110 g
Customs tariff number 85437090
Country of origin DE
 

Classifications

ECLASS

ECLASS-11.0 27210129
ECLASS-12.0 27210129
ECLASS-13.0 27210129
 

ETIM

ETIM 9.0 EC002919
 

UNSPSC

UNSPSC 21.0 41112100
 

Approvals

EAC

Approval ID: EAC-Zulassung
 

DNV GL

Approval ID: TAA00002UA
 

UL Listed

Approval ID: FILE E 238705
 

cUL Listed

Approval ID: FILE E 238705
 

IECEx

Approval ID: IECEx_BVS_20.0017X
 

cUL Listed

Approval ID: FILE E 196811
 

UL Listed

Approval ID: FILE E 196811
 

ATEX

Approval ID: BVS 20 ATEX E 024 X
 

cULus Listed

 

cULus Listed

 

Environmental product compliance

 
REACh SVHC Lead 7439-92-1
 
China RoHS Environmentally Friendly Use Period = 50 years
For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”


- Tài liệu kỹ thuật Phoenix Contact MINI MCR-2-RTD-UI-PT - 2902052 ở đây.

 

Accessories

ME 6,2 TBUS-2 1,5/5-ST-3,81 GY - DIN rail bus connectors
2695439

ME 6,2 TBUS-2 1,5/5-ST-3,81 GN - DIN rail bus connectors
2869728

TC-D37SUB-AIO16-MP-PS-UNI - Module carrier
2906640

TC-D37SUB-ADIO16-MP-P-UNI - Module carrier
2906639

MINI MCR-2-V8-FLK 16 - System adapter
2901993

MINI MCR-2-V8-MOD-RTU - Communication module
2905634

MINI MCR-2-V8-MOD-TCP - Communication module
2905635

MINI MCR-2-V8-PB-DP - Communication module
2905636

MINI MCR-2-V8-PN - Communication module
2905637

IFS-USB-PROG-ADAPTER - Programming adapter
2811271

IFS-BT-PROG-ADAPTER - Adapter
2905872

TWN4 MIFARE NFC USB ADAPTER - Programming adapter
2909681

FASTCON PRO-SET - Connector set
2906227

FASTCON PRO-SET-PT - Connector set
2906228

UCT-EM (30X5) - Marker for end clamp
0801505

UCT-EM (30X5) CUS - Marker for end clamp
0801589

SK 5,0 WH:REEL - Marker strip
0805221

UC-EMLP (15X5) - Plastic label
0819301

UC-EMLP (15X5) YE - Plastic label
0822615

UC-EMLP (15X5) CUS - Plastic label
0824550

UC-EMLP (15X5) YE CUS - Plastic label
0824551

UC-EMLP (15X5) SR - Plastic label
0828095

UC-EMLP (15X5) SR CUS - Plastic label
0828099

US-EMLP (15X5) - Plastic label
0828790

US-EMLP (15X5) YE - Plastic label
0828873

US-EMLP (15X5) SR - Plastic label
0828874

US-EMLP (15X5) CUS - Plastic label
0830076

US-EMLP (15X5) YE CUS - Plastic label
0830077

US-EMLP (15X5) SR CUS - Plastic label
0830078

UCT-EM (30X5) YE - Marker for end clamp
0830340

UCT-EM (30X5) YE CUS - Marker for end clamp
0830348

MINI MCR-2-PTB - Power terminal block
2902066

MINI MCR-2-PTB-PT - Power terminal block
2902067

QUINT4-SYS-PS/1AC/24DC/2.5/SC - Power supply unit
2904614

MINI MCR-2-FM-RC - Monitoring block
2904504

MINI MCR-2-FM-RC-PT - Monitoring block
2904508
SZS 0,6X3,5 - Screwdriver
1205053



Tham khảo thêm các model khác cùng loại:
MACX MCR-UI-UI-NC - Signal conditioner
2811446

Configurable 3-way isolating amplifier with safe electrical isolation, 24 V, power bridging. DIP switches on the front, over 1600 signal conversions can be set. Standard configuration (IN 0 ... 10 V/OUT 0 ... 20 mA), screw connection, SIL.

MACX MCR-SL-2I-2I-ILP - Loop-powered isolators
2905280

2-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Screw connection technology.

MACX MCR-SL-NAM-2RO-SP - Isolation amplifier
2924265

NAMUR signal conditioner for operating proximity sensors and switches. The signals are transferred to the control level using 2 isolated relay outputs (N/O contact). Line fault detection (LFD), 3-way electrical isolation, SIL 2, Push-in connection.

MACX MCR-SL-RPSSI-I-SP - Power/input isolating amplifier
2924207

Repeater power supply and input signal conditioner, HART-transparent. Transmits supplied or active 0/4 … 20 mA signals to a load (active or passive). 3-way electrical isolation, SIL 2 in accordance with IEC 61508.

MACX MCR-SL-NAM-2RO - Isolation amplifier
2865010

NAMUR signal conditioner for operating proximity sensors and switches. The signals are transferred to the control level using 2 isolated relay outputs (N/O contact). Line fault detection (LFD), 3-way electrical isolation, SIL 2, screw connection.

MACX MCR-SL-I-I-ILP - Loop-powered isolators
2905278

1-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Screw connection technology.

MACX MCR-SL-RPSSI-2I-SP - Repeater power supply
2924838

Measuring transducer repeater power supply and input signal conditioner, HART-transparent. Transmits supplied or active 0/4 mA … 20 mA electrically isolated signals from the field to two loads. 4-way electrical isolation, Push-in connection, SIL, PL.

MACX MCR-T-UI-UP - Temperature measuring transducer
2811394

Electrical Number: 4301392
Freely programmable temperature transducer with analog output and 1 limit value relay, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.

MACX MCR-SL-2NAM-RO - Isolation amplifier
2865049

NAMUR 2-channel signal conditioner for operating proximity sensors and switches. The signals are transferred to the control level using relay outputs (N/O contact). Line fault detection, 3-way electrical isolation, SIL 2, screw connection.

MACX MCR-SL-RPSSI-I - Power/input isolating amplifier
2865955

Repeater power supply and input signal conditioner, HART-transparent. Transmits supplied or active 0/4 … 20 mA signals to a load (active or passive). 3-way electrical isolation, SIL 2 in accordance with IEC 61508.

MACX MCR-UI-UI-UP-NC - Signal conditioner
2811297

Isolating amplifier with safe electrical isolation and wide-range power supply (24 V ... 230 V AC/DC). DIP switches on the front, over 1600 signal conversions can be set. Standard configuration (IN 0 ... 10 V/OUT 0 ... 20 mA), screw connection, SIL.

MINI MCR-SL-I-I - Signal conditioner
2864406

Electrical Number: 4514053
MCR 3-way isolating amplifier, for electrical isolation of analog signals, with screw connection, input signal: 0(4) mA ... 20 mA, output signal: 0(4) mA ... 20 mA

MACX MCR-SL-RPSSI-2I - Repeater power supply
2924825

Measuring transducer repeater power supply and input signal conditioner, HART-transparent. Transmits supplied or active 0/4…20 mA electrically isolated signals from the field to two loads. 4-way electrical isolation, screw connection, SIL, PL.

MACX MCR-UI-UI-UP - Signal conditioner
2811459

Configurable 3-way isolating amplifier with safe electrical isolation and wide-range power supply (24 V ... 230 V AC/DC). DIP switches on the front, over 1600 signal conversions can be set. Order configuration, screw connection, SIL.

MACX MCR-RTD-I-SP - Temperature measuring transducer
1050201

Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, Push-in connection, SIL, 3-way electrical isolation, standard configuration.

MACX MCR-UI-UI - Signal conditioner
2811284

Configurable 3-way isolating amplifier with safe electrical isolation, 24 V, power bridging. DIP switches on the front, over 1600 signal conversions can be set. Order configuration, screw connection, SIL.

MINI MCR-2-I-I-PT - Signal conditioner
2901999

3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 0(4) mA ... 20 mA, output signal: 0(4) mA ... 20 mA, push-in connection technology.

MINI MCR-SL-NAM-2RNO - Switching amplifier
2864105

Configurable NAMUR switching amplifier for proximity sensors, floating switching contacts and switching contacts with resistance circuit. On the output side 2 N/O contact, with screw connection

MACX MCR-T-UI-UP-SP - Temperature measuring transducer
2811860

Freely programmable temperature transducer with analog output and 1 limit value relay, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.

MACX MCR-IDS-I-I-SP - Output signal conditioner
2908064

Output signal conditioner, HART-transparent. Isolates and transmits 0/4 mA ... 20 mA signals to a load in the safe area. 3-way electrical isolation, line fault detection (can be switched off via DIP switch), SIL 2 (SC3) in accordance with IEC 61508, Push-in connection.

MACX MCR-SL-NAM-R-SP - Isolation amplifier
2924252

NAMUR signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via relay output (changeover contact). Line fault detection (LFD), 3-way electrical isolation, SIL 2, with Push-in connection.

MACX MCR-SL-2NAM-T-SP - Isolation amplifier
2924281

NAMUR 2-channel signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via transistor outputs (passive). Line fault detection, 3-way electrical isolation, SIL 2, Push-in connection.

MACX MCR-UI-UI-UP-SP-NC - Signal conditioner
2811569

Isolating amplifier with safe electrical isolation and wide-range power supply (24 V ... 230 V AC/DC). DIP switches on the front, over 1600 signal conversions can be set. Standard configuration (IN 0 ... 10 V/OUT 0 ... 20 mA), spring-cage connection, SIL.

MACX MCR-T-UIREL-UP - Temperature measuring transducer
2811378

Freely programmable temperature transducer with analog output and 3 limit value relays, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.

MACX MCR-UI-UI-SP-NC - Signal conditioner
2811556

Configurable 3-way isolating amplifier with safe electrical isolation, 24 V, power bridging. DIP switches on the front, over 1600 signal conversions can be set. Standard configuration (IN 0 ... 10 V/OUT 0 ... 20 mA), spring-cage connection, SIL.

MACX MCR-RTD-I - Temperature measuring transducer
1050192

Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, screw connection, SIL, 3-way electrical isolation, standard configuration.

MACX MCR-IDS-I-I - Output signal conditioner
2908063

Output signal conditioner, HART-transparent. Isolates and transmits 0/4 mA ... 20 mA signals to a load in the safe area. 3-way electrical isolation, line fault detection (can be switched off via DIP switch), SIL 2 (SC3) in accordance with IEC 61508, screw connection.

MINI MCR-2-RPSS-I-I-PT - Repeater power supply
2902015

3-way repeater power supply with plug-in connection technology. HART-transparent, input signal 0(4) mA ... 20 mA, output signal 0(4) mA ... 20 mA. The device can be used in both isolator and repeater power supply operation. push-in connection technology

MINI MCR-SL-UI-2I-NC - Signal duplicator
2864176

Electrical Number: 4311211
4-way signal duplicator for electrical isolation and duplication of analog signals with screw connection, standard configuration

MINI MCR-SL-UI-UI-NC - Signal conditioner
2864150

Electrical Number: 4500101
3-way isolating amplifier for the electrical isolation of analog signals, I/O can be configured via DIP switches, with screw connection, standard configuration

MINI MCR-SL-R-UI - Resistance/potiposition transducer
2864095

MCR potiposition transducer for conversion of potentiometer positions into a standard analog signal, 0 Ω input... 100 Ω to 0 kΩ ... 100 kΩ

MINI MCR-2-RTD-UI-PT - Resistance thermometer measuring transducer
2902052

Electrical Number: 4311207
Configurable temperature transducer with plug-in connection technology for connecting 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Configurable via DIP switch or software. push-in connection technology, standard configuration

MINI MCR-2-2I-2I-ILP-PT - Loop-powered isolators
2901997

2-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.

MINI MCR-2-U-U-PT - Signal conditioner
2902043

3-way signal conditioner with plug-in connection technology for the electrical isolation of unipolar and bipolar analog signals. Input signal: 0 ... 10 V/±10 V, output signal: 0 ... 10 V/±10 V, push-in connection technology.

MINI MCR-2-UNI-UI-2UI - Signal duplicator
2905026

Universally configurable 4-way signal duplicator, with plug-in connection technology for the electrical isolation and duplication of analog signals. Configurable via DIP switch or software. Screw connection technology, standard configuration.

MINI MCR-SL-RPS-I-I - Repeater power supply
2864422

Electrical Number: 4514055
MCR repeater power supplies, screw connection, input signal: (0)4..20 mA, output signal: (0)4..20 mA

MINI MCR-2-UI-UI-PT - Signal conditioner
2902040

Electrical Number: 4311206
3-way signal conditioner with plug-in connection technology and calibrated measuring range changeover, for the electrical isolation of unipolar and bipolar analog signals. Input/output configurable via DIP switch. push-in connection technology, standard configuration.

MINI MCR-SL-UI-I-LP-NC - Signal conditioner
2902829

2-way loop-powered isolating amplifier (supplied on the output side), can be configured via DIP switches, with screw connection technology and standard configuration.

MINI MCR-SL-PT100-UI-NC - Resistance thermometer measuring transducer
2864273

Electrical Number: 4514058
MCR temperature transducer for Pt 100 temperature sensors, configured via DIP switches, with screw connection, not preconfigured

MINI MCR-SL-1CP-I-I - Loop-powered isolators
2864419

Electrical Number: 4514056
MCR loop-powered isolator, 1-channel, for the electrical isolation of current signals without auxiliary power, with screw connection

MINI MCR-2-F-UI - Frequency measuring transducer
2902056

Universally configurable frequency transducer for converting frequency (Hz/rpm) and PWM signals into standard signals. Sensor voltages greater than 8.2 V DC are possible in combination with MINI MCR-2-SPS 1033202. Screw connection technology.

MINI MCR-2-I-I - Signal conditioner
2901998

3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 0(4) mA ... 20 mA, output signal: 0(4) mA ... 20 mA, screw connection technology

MINI MCR-2-UNI-UI-UIRO - Signal conditioner
2902026

Universally configurable 4-way signal conditioner, with switching output and plug-in connection technology for the electrical isolation of analog signals. Configurable via DIP switch or software. Screw connection technology, standard configuration.

MINI MCR-2-UI-UI - Signal conditioner
2902037

3-way signal conditioner with plug-in connection technology and calibrated measuring range changeover for the electrical isolation of unipolar and bipolar analog signals. Input/output configurable via DIP switch. Screw connection technology, standard configuration.

MINI MCR-2-NAM-2RO-PT - Isolation amplifier
2902005

Configurable NAMUR signal conditioner with plug-in connection technology for proximity sensors, floating switch contacts, and switch contacts with resistance circuit. 2 transistor outputs. Configurable via DIP switch. Push-in connection technology.

MINI MCR-SL-2CP-I-I - Loop-powered isolators
2864655

Electrical Number: 4514057
MCR passive isolator, 2-channel, for the electrical isolation of current signals without auxiliary power, with screw connection

MINI MCR-RTD-UI-NC - Resistance thermometer measuring transducer
2902849

Configurable temperature transducer for the connection of 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Can be configured via DIP switches or, with extended functionality, using the software. Screw connection, standard configuration.

MINI MCR-2-U-I4-PT - Signal conditioner
2902030

3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 0 V ... 10 V, output signal: 4 mA ... 20 mA, push-in connection technology

MINI MCR-2-UNI-UI-2UI-PT - Signal duplicator
2905028

Universally configurable 4-way signal duplicator, with plug-in connection technology for the electrical isolation and duplication of analog signals. Configurable via DIP switch or software. Push-in connection technology, standard configuration.

MINI MCR-SL-UI-REL - Limit value switch
2864480

Electrical Number: 4514060
MCR limit value switch, with adjustable hysteresis and delay time, with screw connection

MINI MCR-SL-PT100-UI-200-NC - Temperature measuring transducer
2864370

MCR temperature transducer, configurable, for Pt 100 temperature sensors, with screw-connection, not configured

MINI MCR-2-I-I-ILP-PT - Loop-powered isolators
2901995

1-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.

MACX MCR-SL-UI-REL - Limit value switch
2906169

Limit value switch with input for active current and voltage signals and a limit-value relay output (changeover contact). Can be set via DIP switch and potentiometer, galvanic 3-way electrical isolation, up to SIL2 (SC3), PLc Cat.1, screw connection.

MACX MCR-SL-I-I-ILP-SP - Loop-powered isolators
2905279

1-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.

MACX MCR-SL-2NAM-RO-SP - Isolation amplifier
2924294

NAMUR 2-channel signal conditioner for operating proximity sensors and switches. The signals are transferred to the control level using relay outputs (N/O contact). Line fault detection, 3-way electrical isolation, SIL 2, Push-in connection.

MACX MCR-SL-RPSSI-I-UP - Repeater power supply
2865968

Repeater power supply for supplying 2- and 3-conductor transmitters with Hart transparency and wide-range power supply, SIL 2 (1oo1)/SIL 3 (1oo2), screw connection

MINI MCR-2-UI-REL-PT - Limit value switch
2902035

Universally configurable threshold value switch with changeover contact relay output and plug-in connection technology for switching analog limit values. Configurable via DIP switch or software. Push-in connection technology, standard configuration.

MINI MCR-SL-UI-F - Frequency measuring transducer
2864082

Analog frequency transducers for converting analog standard signals into frequency signals or PWM signals, configurable via DIP switch, with screw connection

MINI MCR-2-UI-REL - Limit value switch
2902033

Universally configurable threshold value switch with changeover contact relay output and plug-in connection technology for switching analog limit values. Configurable via DIP switch or software. Screw connection technology, standard configuration.

MINI MCR-2-RPSS-I-2I-PT - Repeater power supply
2905629

4-way power supply doubler with plug-in connection technology. HART-transparent, 0(4) mA ... 20 mA input signal, 0(4) mA ... 20 mA output signals. The device can be used in both signal and power supply doubler modes. Push-in connection technology.

MINI MCR-TC-UI-NC - Thermocouple measuring transducer
2902851

Configurable temperature transducer for the connection of thermocouples. Can be configured via DIP switches or, with extended functionality, using the software. Screw connection, standard configuration.

MINI MCR-SL-F-UI-NC - Frequency measuring transducer
2902832

The configurable frequency transducer is suitable for the connection of NAMUR proximity sensors as well as for sensors with NPN and PNP outputs. Configurable via DIP switch and teach-in wheel. Screw connection, standard configuration.

MINI MCR-SL-PT100-LP-NC - Temperature measuring transducer
2810308

Configurable loop-powered temperature transducer for Pt 100 temperature sensors, configured via DIP switches, with screw connection, not preconfigured

MINI MCR-2-F-UI-PT - Frequency measuring transducer
2902058

Universally configurable frequency transducer for converting frequency (Hz/rpm) and PWM signals into standard signals. Sensor voltages greater than 8.2 V DC are possible in combination with MINI MCR-2-SPS-PT 1033201. Push-in connection technology.

MINI MCR-2-U-UI - Signal conditioner
2902019

3-way signal conditioner, with configurable input/output, for electrical isolation and conversion of analog signals in the mV and V range, unipolar as well as bipolar. Screw connection technology, standard configuration.

MACX MCR-SL-2NAM-T - Isolation amplifier
2865036

NAMUR 2-channel signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via transistor outputs (passive). Line fault detection, 3-way electrical isolation, SIL 2, screw connection.

MACX MCR-RTD-I-C - Temperature measuring transducer
1052472

Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, screw connection, SIL, 3-way electrical isolation, order configuration.

MACX MCR-T-UIREL-UP-SP - Temperature measuring transducer
2811828

Freely programmable temperature transducer with analog output and 3 limit value relays, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.

MACX MCR-RTD-I-SP-C - Temperature measuring transducer
1052464

Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, Push-in connection, SIL, 3-way electrical isolation, order configuration.

MACX MCR-T-UI-UP-C - Temperature measuring transducer
2811873

Freely programmable temperature transducer with analog output and 1 limit value relay, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.

MACX MCR-T-UI-UP-SP-C - Temperature measuring transducer
2811970

Freely programmable temperature transducer with analog output and 1 limit value relay, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.

MACX MCR-UI-UI-UP-SP - Signal conditioner
2811585

Configurable 3-way isolating amplifier with safe electrical isolation and wide-range power supply (24 V ... 230 V AC/DC). DIP switches on the front, over 1600 signal conversions can be set. Order configuration, spring-cage connection, SIL.

MACX MCR-SL-RPSS-2I-2I-SP - Repeater power supply
2904090

2-channel repeater power supply for operating 2-conductor measuring transducers, input: 4 ... 20 mA (supplying), output: 4 ... 20 mA (active), bidirectional transmission with digital HART transparency, Push-in connection, SIL, PL.

MACX MCR-SL-2I-2I-ILP-SP - Loop-powered isolators
2905281

2-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.

MACX MCR-SL-NAM-R - Isolation amplifier
2865997

NAMUR signal conditioners for operating proximity sensors and switches. The signals are transmitted to the control level via relay output (changeover contact). Line fault detection (LFD), 3-way electrical isolation, SIL 2, with screw connection.

MACX MCR-T-UIREL-UP-SP-C - Temperature measuring transducer
2811831

Freely programmable temperature transducer with analog output and 3 limit value relays, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.

MACX MCR-TC-I-C - Temperature measuring transducer
1052459

Temperature transducer: converts signals from thermocouples and mV sources into 0/4…20 mA signals. Order configuration, freely programmable, 3-way electrical isolation, screw connection, SIL.

MACX MCR-SL-2NAM-R-UP-SP - Isolation amplifier
2924304

2-channel NAMUR signal conditioner with wide range power supply for proximity sensors and switches. In terms of signal output, for each channel there is a relay with a changeover contact available. Line fault detection (LFD), 3-way isolation, Push-in connection, SIL 2.

MACX MCR-SL-2NAM-R-UP - Isolation amplifier
2865052

2-channel NAMUR signal conditioner with wide range power supply for proximity sensors and switches. In terms of signal output, for each channel there is a relay with a changeover contact available. Line fault detection (LFD), 3-way isolation, screw connection, SIL 2.

MACX MCR-SL-NAM-2T-SP - Isolation amplifier
2924278

NAMUR signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via 2 transistor outputs (passive). Line fault detection, 3-way electrical isolation, SIL 2, Push-in connection.

MACX MCR-SL-RPSSI-I-UP-SP - Repeater power supply
2924210

Repeater power supply for supplying 2- and 3-conductor transmitters with HART transparency and wide-range power supply, SIL 2 (1oo1)/SIL 3 (1oo2), Push-in connection

MACX MCR-IDS-2I-2I-SP - Output signal conditioner
2908066

2-channel output signal conditioner, HART-transparent. Isolates and transmits 0/4 mA ... 20 mA signals to a load in the safe area. 4-way electrical isolation, line fault detection, SIL 2 (SC3) in accordance with IEC 61508, Push-in connection.

MACX MCR-TC-I - Temperature measuring transducer
1050228

Temperature transducer: converts signals from thermocouples and mV sources into 0/4…20 mA signals. Freely programmable, 3-way electrical isolation, screw connection, SIL.

MACX MCR-UI-UI-SP - Signal conditioner
2811572

Configurable 3-way isolating amplifier with safe electrical isolation, 24 V, power bridging. DIP switches on the front, over 1600 signal conversions can be set. Order configuration, spring-cage connection, SIL.

MACX MCR-SL-NAM-2T - Isolation amplifier
2865023

NAMUR signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via 2 transistor outputs (passive). Line fault detection, 3-way electrical isolation, SIL 2, screw connection.

MACX MCR-IDS-2I-2I - Output signal conditioner
2908065

2-channel output signal conditioner, HART-transparent. Isolates and transmits 0/4 mA ... 20 mA signals to a load in the safe area. 4-way electrical isolation, line fault detection, SIL 2 (SC3) in accordance with IEC 61508, screw connection.

SẢN PHẨM XEM NHIỀU
Gọi điện thoại