Bộ chuyển phát tín hiệu nhiệt Phoenix Contact MINI MCR-TC-UI-NC - 2902851

THÔNG TIN THAM KHẢO

• Danh mục Model sản phẩm PHOENIX CONTACT

• 

  Tìm hiểu về điều hòa, lọc nhiểu, khuếch đại, chuyển đổi tín hiệu điều khiển và đo lường MCR

• Xem thêm

Bộ chuyển phát tín hiệu nhiệt Phoenix Contact MINI MCR-TC-UI-NC - 2902851

 

Mô tả sản phẩm

- The configurable temperature transducer with 3-way isolation is suitable for the connection of thermocouples.
- The measured values are converted into a linear current or voltage signal.
- You can configure the device using one of the free software solutions. Default settings can also be made directly on the device by simply using the DIP switches (see configuration table). The measuring transducer supports fault monitoring.

 

Thông số kỹ thuật

Chú ý

Utilization restriction
EMC note	EMC: class A product, see manufacturer's declaration in the download area

 

Tính chất sản phẩm

Product type	Temperature transmitter
Product family	MINI Analog
Configuration	DIP switches
	Software
Insulation characteristics
Overvoltage category	II
Pollution degree	2

 

Thông số điện

Electrical isolation	3-way isolation
Typical cold point errors	< 2 K
Cold point error, max.	< 3 K
Protective circuit	Transient protection
Step response (0–99%)	400 ms (Highspeed Mode: typ. 150 ms)
Maximum temperature coefficient	≤ 0.01 %/K
Transmission error thermocouples	0.1 % * 600 K / set measuring range; 0.1 % > 600 K (E, J, K, N, T, L, U, M Gost, L Gost)
	0.2 % * 600 K / set measuring range; 0.2 % > 600 K (B, R, S, A1, A2, A3)
	0.2% * 600 K / set measuring range; 0.2% > 600 K (E, J, K, N, T, L, U, M Gost, L Gost); Highspeed Mode
	0.4% * 600 K / set measuring range; 0.4% > 600 K (B, R, S, A1, A2, A3); Highspeed Mode
Electrical isolation Input/output/power supply
Rated insulation voltage	50 V AC/DC
Test voltage	1.5 kV AC (50 Hz, 60 s)
Insulation	Basic insulation in accordance with IEC/EN 61010
Supply
Supply voltage range	9.6 V DC ... 30 V DC (The DIN rail connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, item no. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail in accordance with EN 60715)
Typical current consumption	< 27 mA (at 24 V DC)
Max. current consumption	72 mA
Power consumption	≤ 700 mW (at IOUT = 20 mA, 9.6 V DC, load 500 Ω)

 

Thông số đầu vào

Signal
Number of inputs	1
Measurement
Number of inputs	1
Configurable/programmable	Yes
Sensor types that can be used (TC)	B, E, J, K, N, R, S, T, L, U, A-1, A-2, A-3, M, L
Temperature measuring range	-250 °C ... 2500 °C (Range depends on sensor type, range can be set freely via software or in increments from -150°C to 1350°C via DIP switches)
Temperature measuring range	min. 50 K
Sensor type:	500 °C ... 1820 °C
	-230 °C ... 1000 °C
	-210 °C ... 1200 °C
	-250 °C ... 1372 °C
	-200 °C ... 1300 °C
	-50 °C ... 1768 °C
	-50 °C ... 1768 °C
	-200 °C ... 400 °C
	-200 °C ... 900 °C
	-200 °C ... 600 °C
	0 °C ... 2500 °C
	0 °C ... 1800 °C
	0 °C ... 1800 °C
	-200 °C ... 100 °C
	-200 °C ... 800 °C

 

Thông số đầu ra

Signal: Voltage/current
Number of outputs	1
Configurable/programmable	Yes
Voltage output signal	0 V ... 5 V
	1 V ... 5 V
	0 V ... 10 V
	10 V ... 0 V
Max. voltage output signal	approx. 12.3 V
Non-load voltage	< 17.5 V
Current output signal	0 mA ... 20 mA
	4 mA ... 20 mA
	20 mA ... 0 mA
	20 mA ... 4 mA
Max. current output signal	24.6 mA
Short-circuit current	< 31.5 mA
Load/output load voltage output	≥ 10 kΩ
Load/output load current output	< 500 Ω (at 20 mA)
Ripple	< 20 mVPP
	< 20 mVPP (at 500 Ω)

 

Thông số kết nối

Connection method	Screw connection
Stripping length	12 mm
Screw thread	M3
Conductor cross section solid	0.2 mm² ... 2.5 mm²
Conductor cross section flexible	0.2 mm² ... 2.5 mm²
Conductor cross section AWG	26 ... 12

 

Thông số giao diện

Data: IFS interface
Connection method	S-PORT

 

Thông số LED hiển thị

Status display

LED red

 

Thông số kích thước

Width	6.2 mm
Height	93.1 mm
Depth	101.2 mm

 

Thông số cơ học

Fire protection for rail vehicles (DIN EN 45545-2) R22	HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R23	HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R24	HL 1 - HL 2
Housing material	PBT

 

Thông số điều kiện môi trường vận hành

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-20 °C ... 65 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Altitude	≤ 2000 m
Permissible humidity (operation)	5 % ... 95 % (non-condensing)

 

Approval data

CE
Certificate	CE-compliant
UKCA
Certificate	UKCA-compliant
UL, USA/Canada
Identification	UL 508 Listed
	Class I, Div. 2, Groups A, B, C, D T4
	Class I, Zone 2, Group IIC
Shipbuilding approval
Certificate	DNV GL TAA00002R0
DNV GL data
Temperature	B
Humidity	B
Vibration	B
EMC	A
Enclosure	Required protection according to the Rules shall be provided upon installation on board

 

EMC data

Electromagnetic compatibility	Conformance with EMC directive
Noise emission	EN 61000-6-4
Noise immunity	EN 61000-6-2
Note	When being exposed to interference, there may be minimal deviations.
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Comments	Safety measures must be taken to prevent electrostatic discharge.
Electromagnetic HF field
Designation	Electromagnetic RF field
Standards/regulations	EN 61000-4-3
Typical deviation from the measuring range final value	0.15 %
Fast transients (burst)
Designation	Fast transients (burst)
Standards/regulations	EN 61000-4-4
Typical deviation from the measuring range final value	0.05 %
Surge current load (surge)
Standards/regulations	EN 61000-4-5
Conducted interference
Designation	Conducted interferences
Standards/regulations	EN 61000-4-6
Typical deviation from the measuring range final value	0.02 %

 

Quy-Chuẩn

Electrical isolation

3-way isolation

 

Thông số lắp đặt

Mounting type	DIN rail mounting
Mounting position	any

 

Thông số thương mại

Item number	2902851
Packing unit	1 pc
Minimum order quantity	1 pc
Product Key	CK1221
Catalog Page	Page 107 (C-7-2015)
GTIN	4046356689229
Weight per Piece (including packing)	117.8 g
Weight per Piece (excluding packing)	117.8 g
Customs tariff number	85437090
Country of origin	DE

 

ECLASS

ECLASS-10.0.1	27210129
ECLASS-11.0	27210129

 

ETIM

ETIM 8.0

EC002919

 

UNSPSC

UNSPSC 21.0

41112100

 

ApprovalsDNV GL

Approval ID: TAA00002R0
UL Listed
Approval ID: FILE E 238705
cUL Listed
Approval ID: FILE E 238705
cUL Listed
Approval ID: FILE E 199827
UL Listed
Approval ID: FILE E 199827
 

Thông số an toàn môi trường

REACh SVHC	Lead 7439-92-1
China RoHS	Environmentally Friendly Use Period = 50 years
	For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”

- Tài liệu kỹ thuật Phoenix Contact MINI MCR-TC-UI-NC - 2902851 ở đây.


Tham khảo thêm các model khác cùng loại:

MACX MCR-T-UI-UP - Temperature measuring transducer

2811394
Freely programmable temperature transducer with analog output and 1 limit value relay, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.
 

MACX MCR-UI-UI-NC - Signal conditioner

2811446
Configurable 3-way isolating amplifier with safe electrical isolation, 24 V, power bridging. DIP switches on the front, over 1600 signal conversions can be set. Standard configuration (IN 0 ... 10 V/OUT 0 ... 20 mA), screw connection, SIL.
 

MACX MCR-UI-UI-UP-NC - Signal conditioner

2811297
Isolating amplifier with safe electrical isolation and wide-range power supply (24 V ... 230 V AC/DC). DIP switches on the front, over 1600 signal conversions can be set. Standard configuration (IN 0 ... 10 V/OUT 0 ... 20 mA), screw connection, SIL.
 

MACX MCR-SL-I-I-ILP - Loop-powered isolators

2905278
1-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Screw connection technology.
 

MACX MCR-SL-RPSSI-I - Power/input isolating amplifier

2865955
Repeater power supply and input signal conditioner, HART-transparent. Transmits supplied or active 0/4 … 20 mA signals to a load (active or passive). 3-way electrical isolation, SIL 2 in accordance with IEC 61508.
 

MACX MCR-T-UIREL-UP - Temperature measuring transducer

2811378
Freely programmable temperature transducer with analog output and 3 limit value relays, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.
 

MACX MCR-SL-RPSSI-2I - Repeater power supply

2924825
Measuring transducer repeater power supply and input signal conditioner, HART-transparent. Transmits supplied or active 0/4…20 mA electrically isolated signals from the field to two loads. 4-way electrical isolation, screw connection, SIL, PL.
 

MACX MCR-SL-2NAM-RO - Isolation amplifier

2865049
NAMUR 2-channel signal conditioner for operating proximity sensors and switches. The signals are transferred to the control level using relay outputs (N/O contact). Line fault detection, 3-way electrical isolation, SIL 2, screw connection.
 

MACX MCR-UI-UI-UP-SP-NC - Signal conditioner

2811569
Isolating amplifier with safe electrical isolation and wide-range power supply (24 V ... 230 V AC/DC). DIP switches on the front, over 1600 signal conversions can be set. Standard configuration (IN 0 ... 10 V/OUT 0 ... 20 mA), spring-cage connection, SIL.
 

MACX MCR-SL-UI-REL-SP - Limit value switches

2906170
Limit value switch with input for active current and voltage signals and a limit-value relay output (changeover contact). Can be set via DIP switch and potentiometer, galvanic 3-way electrical isolation, up to SIL2 (SC3), PLc Cat.1, Push-in connection.
 

MACX MCR-SL-RPSSI-I-UP-SP - Repeater power supply

2924210
Repeater power supply for supplying 2- and 3-conductor transmitters with HART transparency and wide-range power supply, SIL 2 (1oo1)/SIL 3 (1oo2), Push-in connection
 

MACX MCR-RTD-I - Temperature measuring transducer

1050192
Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, screw connection, SIL, 3-way electrical isolation, standard configuration.
 

MACX MCR-SL-2I-2I-ILP - Loop-powered isolators

2905280
2-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Screw connection technology.
 

MACX MCR-SL-2NAM-RO-SP - Isolation amplifier

2924294
NAMUR 2-channel signal conditioner for operating proximity sensors and switches. The signals are transferred to the control level using relay outputs (N/O contact). Line fault detection, 3-way electrical isolation, SIL 2, Push-in connection.
 

MACX MCR-SL-2NAM-R-UP-SP - Isolation amplifier

2924304
2-channel NAMUR signal conditioner with wide range power supply for proximity sensors and switches. In terms of signal output, for each channel there is a relay with a changeover contact available. Line fault detection (LFD), 3-way isolation, Push-in connection, SIL 2.
 

MACX MCR-SL-RPSSI-I-UP - Repeater power supply

2865968
Repeater power supply for supplying 2- and 3-conductor transmitters with Hart transparency and wide-range power supply, SIL 2 (1oo1)/SIL 3 (1oo2), screw connection
 

MACX MCR-SL-RPSSI-I-SP - Power/input isolating amplifier

2924207
Repeater power supply and input signal conditioner, HART-transparent. Transmits supplied or active 0/4 … 20 mA signals to a load (active or passive). 3-way electrical isolation, SIL 2 in accordance with IEC 61508.
 

MINI MCR-SL-UI-2I-NC - Signal duplicator

2864176
4-way signal duplicator for electrical isolation and duplication of analog signals with screw connection, standard configuration
 

MINI MCR-SL-PT100-UI-NC - Resistance thermometer measuring transducer

2864273
MCR temperature transducer for Pt 100 temperature sensors, configured via DIP switch, with screw connection, not pre-configured
 

MACX MCR-IDS-I-I-SP - Output signal conditioner

2908064
Output signal conditioner, HART-transparent. Isolates and transmits 0/4 mA ... 20 mA signals to a load in the safe area. 3-way electrical isolation, line fault detection (can be switched off via DIP switch), SIL 2 (SC3) in accordance with IEC 61508, Push-in connection.
 

MACX MCR-SL-NAM-2RO - Isolation amplifier

2865010
NAMUR signal conditioner for operating proximity sensors and switches. The signals are transferred to the control level using 2 isolated relay outputs (N/O contact). Line fault detection (LFD), 3-way electrical isolation, SIL 2, screw connection.
 

MACX MCR-T-UIREL-UP-SP - Temperature measuring transducer

2811828
Freely programmable temperature transducer with analog output and 3 limit value relays, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.
 

MACX MCR-T-UI-UP-C - Temperature measuring transducer

2811873
Freely programmable temperature transducer with analog output and 1 limit value relay, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.
 

MACX MCR-SL-RPSS-2I-2I-SP - Repeater power supply

2904090
2-channel repeater power supply for operating 2-conductor measuring transducers, input: 4 ... 20 mA (supplying), output: 4 ... 20 mA (active), bidirectional transmission with digital HART transparency, Push-in connection, SIL, PL.
 

MACX MCR-SL-NAM-R - Isolation amplifier

2865997
NAMUR signal conditioners for operating proximity sensors and switches. The signals are transmitted to the control level via relay output (changeover contact). Line fault detection (LFD), 3-way electrical isolation, SIL 2, with screw connection.
 

MACX MCR-UI-UI-UP - Signal conditioner

2811459
Configurable 3-way isolating amplifier with safe electrical isolation and wide-range power supply (24 V ... 230 V AC/DC). DIP switches on the front, over 1600 signal conversions can be set. Order configuration, screw connection, SIL.
 

MACX MCR-SL-UI-REL - Limit value switches

2906169
Limit value switch with input for active current and voltage signals and a limit-value relay output (changeover contact). Can be set via DIP switch and potentiometer, galvanic 3-way electrical isolation, up to SIL2 (SC3), PLc Cat.1, screw connection.
 

MACX MCR-SL-2NAM-R-UP - Isolation amplifier

2865052
2-channel NAMUR signal conditioner with wide range power supply for proximity sensors and switches. In terms of signal output, for each channel there is a relay with a changeover contact available. Line fault detection (LFD), 3-way isolation, screw connection, SIL 2.
 

MACX MCR-SL-NAM-2RO-SP - Isolation amplifier

2924265
NAMUR signal conditioner for operating proximity sensors and switches. The signals are transferred to the control level using 2 isolated relay outputs (N/O contact). Line fault detection (LFD), 3-way electrical isolation, SIL 2, Push-in connection.
 

MACX MCR-RTD-I-SP - Temperature measuring transducer

1050201
Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, Push-in connection, SIL, 3-way electrical isolation, standard configuration.
 

MACX MCR-UI-UI-SP-NC - Signal conditioner

2811556
Configurable 3-way isolating amplifier with safe electrical isolation, 24 V, power bridging. DIP switches on the front, over 1600 signal conversions can be set. Standard configuration (IN 0 ... 10 V/OUT 0 ... 20 mA), spring-cage connection, SIL.
 

MACX MCR-SL-NAM-2T - Isolation amplifier

2865023
NAMUR signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via 2 transistor outputs (passive). Line fault detection, 3-way electrical isolation, SIL 2, screw connection.
 

MACX MCR-UI-UI - Signal conditioner

2811284
Configurable 3-way isolating amplifier with safe electrical isolation, 24 V, power bridging. DIP switches on the front, over 1600 signal conversions can be set. Order configuration, screw connection, SIL.
 

MACX MCR-T-UI-UP-SP - Temperature measuring transducer

2811860
Freely programmable temperature transducer with analog output and 1 limit value relay, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.
 

MACX MCR-SL-RPSS-2I-2I - Repeater power supply

2904089
2-channel repeater power supply for operating 2-conductor measuring transducers, input: 4 ... 20 mA (supplying), output: 4 ... 20 mA (active), bidirectional transmission with digital HART transparency, screw connection, SIL, PL.
 

MINI MCR-SL-R-UI - Resistance/potiposition transducer

2864095
MCR potiposition transducer for conversion of potentiometer positions into a standard analog signal, 0 Ω input... 100 Ω to 0 kΩ ... 100 kΩ
 

MINI MCR-2-UNI-UI-2UI - Signal duplicator

2905026
Universally configurable 4-way signal duplicator, with plug-in connection technology for the electrical isolation and duplication of analog signals. Configurable via DIP switch or software. Screw connection technology, standard configuration.
 

MINI MCR-2-UNI-UI-2UI-PT - Signal duplicator

2905028
Universally configurable 4-way signal duplicator, with plug-in connection technology for the electrical isolation and duplication of analog signals. Configurable via DIP switch or software. Push-in connection technology, standard configuration.
 

MINI MCR-SL-I-I - Signal conditioner

2864406
MCR 3-way isolating amplifier, for electrical isolation of analog signals, with screw connection, input signal: 0(4) mA ... 20 mA, output signal: 0(4) mA ... 20 mA
 

MINI MCR-SL-RPS-I-I - Repeater power supply

2864422
MCR repeater power supplies, screw connection, input signal: (0)4..20 mA, output signal: (0)4..20 mA
 

MINI MCR-SL-UI-UI-NC - Signal conditioner

2864150
3-way isolating amplifier for the electrical isolation of analog signals, I/O can be configured via DIP switches, with screw connection, standard configuration
 

MINI MCR-2-RTD-UI-PT - Resistance thermometer measuring transducer

2902052
Configurable temperature transducer with plug-in connection technology for connecting 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Configurable via DIP switch or software. push-in connection technology, standard configuration
 

MINI MCR-SL-RPSS-I-I - Repeater power supply

2864079
MCR repeater power supply with HART transparency, input signal: 4 mA ... 20 mA, output signal: 4 mA ... 20 mA, with screw connection
 

MINI MCR-2-I4-U-PT - Signal conditioner

2902003
3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 4 mA ... 20 mA, output signal: 0 V ... 10 V, push-in connection technology
 

MINI MCR-2-UI-UI - Signal conditioner

2902037
3-way signal conditioner with plug-in connection technology and calibrated measuring range changeover for the electrical isolation of unipolar and bipolar analog signals. Input/output configurable via DIP switch. Screw connection technology, standard configuration.
 

MINI MCR-2-UI-UI-PT - Signal conditioner

2902040
3-way signal conditioner with plug-in connection technology and calibrated measuring range changeover, for the electrical isolation of unipolar and bipolar analog signals. Input/output configurable via DIP switch. push-in connection technology, standard configuration.
 

MINI MCR-2-RTD-UI - Resistance thermometer measuring transducer

2902049
Configurable temperature transducer with plug-in connection technology for connecting 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Configurable via DIP switch or software. Screw connection technology, standard configuration
 

MINI MCR-RTD-UI-NC - Resistance thermometer measuring transducer

2902849
Configurable temperature transducer for the connection of 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Can be configured via DIP switches or, with extended functionality, using the software. Screw connection, standard configuration.
 

MINI MCR-2-I-I - Signal conditioner

2901998
3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 0(4) mA ... 20 mA, output signal: 0(4) mA ... 20 mA, screw connection technology
 

MINI MCR-SL-1CP-I-I - Loop-powered isolators

2864419
MCR loop-powered isolator, 1-channel, for the electrical isolation of current signals without auxiliary power, with screw connection
 

MINI MCR-2-F-UI - Frequency transducer

2902056
Universally configurable frequency transducer for converting frequency (Hz/rpm) and PWM signals into standard signals. Sensor voltages greater than 8.2 V DC are possible in combination with MINI MCR-2-SPS 1033202. Screw connection technology.
 

MINI MCR-2-RPSS-I-2I-PT - Repeater power supply

2905629
4-way power supply doubler with plug-in connection technology. HART-transparent, 0(4) mA ... 20 mA input signal, 0(4) mA ... 20 mA output signals. The device can be used in both signal and power supply doubler modes. Push-in connection technology.
 

MACX MCR-SL-2NAM-T - Isolation amplifier

2865036
NAMUR 2-channel signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via transistor outputs (passive). Line fault detection, 3-way electrical isolation, SIL 2, screw connection.
 

MACX MCR-SL-RPSSI-2I-SP - Repeater power supply

2924838
Measuring transducer repeater power supply and input signal conditioner, HART-transparent. Transmits supplied or active 0/4 mA … 20 mA electrically isolated signals from the field to two loads. 4-way electrical isolation, Push-in connection, SIL, PL.
 

MINI MCR-2-RPSS-I-2I - Repeater power supply

2905628
4-way power supply doubler with plug-in connection technology. HART-transparent, 0(4) mA ... 20 mA input signal, 0(4) mA ... 20 mA output signals. The device can be used in both signal and power supply doubler modes. Screw connection technology.
 

MINI MCR-SL-PT100-LP-NC - Temperature measuring transducer

2810308
Configurable loop-powered temperature transducer for Pt 100 temperature sensors, configured via DIP switches, with screw connection, not pre-configured
 

MINI MCR-SL-PT100-UI-200-NC - Temperature measuring transducer

2864370
MCR temperature transducer, configurable, for Pt 100 temperature sensors, with screw-connection, not configured
 

MINI MCR-2-U-U - Signal conditioner

2902042
3-way signal conditioner with plug-in connection technology for the electrical isolation of unipolar and bipolar analog signals. Input signal: 0 ... 10 V/±10 V, output signal: 0 ... 10 V/±10 V, screw connection technology
 

MINI MCR-2-RPSS-I-I-PT - Repeater power supply

2902015
3-way repeater power supply with plug-in connection technology. HART-transparent, input signal 0(4) mA ... 20 mA, output signal 0(4) mA ... 20 mA. The device can be used in both isolator and repeater power supply operation. push-in connection technology
 

MINI MCR-2-I-I-ILP - Loop-powered isolators

2901994
1-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Screw connection technology.
 

MINI MCR-TC-UI-NC - Thermocouple measuring transducer

2902851
Configurable temperature transducer for the connection of thermocouples. Can be configured via DIP switches or, with extended functionality, using the software. Screw connection, standard configuration.
 

MINI MCR-SL-CVS-24-5-10-NC - Constant voltage source

2902822
Constant voltage source, input voltage 9.6 - 30 V DC, output voltage 10 V, 7.5 V, 5 V, 2.5 V DC, electrically isolated, can be configured via DIP switches, screw connection technology, standard configuration
 

MINI MCR-SL-UI-REL - Limit value switches

2864480
MCR limit value switch, with adjustable hysteresis and delay time, with screw connection
 

MACX MCR-SL-NAM-R-SP - Isolation amplifier

2924252
NAMUR signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via relay output (changeover contact). Line fault detection (LFD), 3-way electrical isolation, SIL 2, with Push-in connection.
 

MACX MCR-SL-I-I-ILP-SP - Loop-powered isolators

2905279
1-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
 

MACX MCR-RTD-I-C - Temperature measuring transducer

1052472
Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, screw connection, SIL, 3-way electrical isolation, order configuration.
 

MACX MCR-RTD-I-SP-C - Temperature measuring transducer

1052464
Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, Push-in connection, SIL, 3-way electrical isolation, order configuration.
 

MACX MCR-T-UI-UP-SP-C - Temperature measuring transducer

2811970
Freely programmable temperature transducer with analog output and 1 limit value relay, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.
 

MACX MCR-UI-UI-UP-SP - Signal conditioner

2811585
Configurable 3-way isolating amplifier with safe electrical isolation and wide-range power supply (24 V ... 230 V AC/DC). DIP switches on the front, over 1600 signal conversions can be set. Order configuration, spring-cage connection, SIL.
 

MACX MCR-SL-2I-2I-ILP-SP - Loop-powered isolators

2905281
2-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
 

MACX MCR-T-UIREL-UP-SP-C - Temperature measuring transducer

2811831
Freely programmable temperature transducer with analog output and 3 limit value relays, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.
 

MACX MCR-SL-2NAM-T-SP - Isolation amplifier

2924281
NAMUR 2-channel signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via transistor outputs (passive). Line fault detection, 3-way electrical isolation, SIL 2, Push-in connection.
 

MACX MCR-TC-I-C - Temperature measuring transducer

1052459
Temperature transducer: converts signals from thermocouples and mV sources into 0/4…20 mA signals. Order configuration, freely programmable, 3-way electrical isolation, screw connection, SIL.
 

MACX MCR-SL-NAM-2T-SP - Isolation amplifier

2924278
NAMUR signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via 2 transistor outputs (passive). Line fault detection, 3-way electrical isolation, SIL 2, Push-in connection.
 

MACX MCR-IDS-2I-2I-SP - Output signal conditioner

2908066
2-channel output signal conditioner, HART-transparent. Isolates and transmits 0/4 mA ... 20 mA signals to a load in the safe area. 4-way electrical isolation, line fault detection, SIL 2 (SC3) in accordance with IEC 61508, Push-in connection.
 

MACX MCR-TC-I - Temperature measuring transducer

1050228
Temperature transducer: converts signals from thermocouples and mV sources into 0/4…20 mA signals. Freely programmable, 3-way electrical isolation, screw connection, SIL.
 

MACX MCR-UI-UI-SP - Signal conditioner

2811572
Configurable 3-way isolating amplifier with safe electrical isolation, 24 V, power bridging. DIP switches on the front, over 1600 signal conversions can be set. Order configuration, spring-cage connection, SIL.
 

MACX MCR-IDS-2I-2I - Output signal conditioner

2908065
2-channel output signal conditioner, HART-transparent. Isolates and transmits 0/4 mA ... 20 mA signals to a load in the safe area. 4-way electrical isolation, line fault detection, SIL 2 (SC3) in accordance with IEC 61508, screw connection.
 

MACX MCR-T-UIREL-UP-C - Temperature measuring transducer

2811514
Freely programmable temperature transducer with analog output and 3 limit value relays, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.
 

MACX MCR-IDS-I-I - Output signal conditioner

2908063
Output signal conditioner, HART-transparent. Isolates and transmits 0/4 mA ... 20 mA signals to a load in the safe area. 3-way electrical isolation, line fault detection (can be switched off via DIP switch), SIL 2 (SC3) in accordance with IEC 61508, screw connection.
 

MINI MCR-2-U-I4-PT - Signal conditioner

2902030
3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 0 V ... 10 V, output signal: 4 mA ... 20 mA, push-in connection technology
 

MINI MCR-SL-I-U-4 - Signal conditioner

2813538
MCR 3-way isolating amplifier, for electrical isolation of analog signals, with screw connection, input signal: 4 mA ... 20 mA, output signal: 0 A ... 10 V
 

MINI MCR-SL-IDS-I-I - Output signal conditioner

2905577
3-way output signal conditioner for transmitting 0/4 ... 20 mA signals from the controller to a load located in the field with simultaneous 3-way electrical isolation between the input, output, and supply, with screw connection
 

MINI MCR-2-POT-UI-PT - Resistance/potiposition transducer

2902017
Configurable potiposition transducer with plug-in connection technology for connecting potentiometers from 0 Ω ... 100 Ω to 0 kΩ ... 100 kΩ. Configurable via DIP switch or software. push-in connection technology, standard configuration
 

MINI MCR-SL-UI-I-LP-NC - Signal conditioner

2902829
2-way loop-powered isolating amplifier (supplied on the output side), can be configured via DIP switches, with screw connection technology and standard configuration.
 

MINI MCR-SL-U-UI-NC - Signal conditioner

2865007
MCR 3-way isolation amplifier, with configurable input/output, for electrical isolation and conversion of analog signals up to 30 V, with screw connection, standard configuration
 

MINI MCR-2-UI-REL-PT - Limit value switches

2902035
Universally configurable threshold value switch with changeover contact relay output and plug-in connection technology for switching analog limit values. Configurable via DIP switch or software. Push-in connection technology, standard configuration.
 

MINI MCR-2-I-I-PT - Signal conditioner

2901999
3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 0(4) mA ... 20 mA, output signal: 0(4) mA ... 20 mA, push-in connection technology.
 

MINI MCR-SL-2CP-I-I - Loop-powered isolators

2864655
MCR passive isolator, 2-channel, for the electrical isolation of current signals without auxiliary power, with screw connection
 

MINI MCR-2-UI-UI-C - Signal conditioner

2902036
3-way signal conditioner with plug-in connection technology and calibrated measuring range changeover for the electrical isolation of unipolar and bipolar analog signals. Input/output configurable via DIP switch. Screw connection technology, order configuration.
 

MINI MCR-2-RPSS-I-I - Repeater power supply

2902014
3-way repeater power supply with plug-in connection technology. HART-transparent, input signal 0(4)...20 mA, output signal 0(4)...20 mA. The device can be used in both isolator and repeater power supply operation. Screw connection technology
 

MINI MCR-2-POT-UI - Resistance/potiposition transducer

2902016
Configurable potiposition transducer with plug-in connection technology for connecting potentiometers from 0 Ω ... 100 Ω to 0 kΩ ... 100 kΩ. Configurable via DIP switch or software. Screw connection technology, standard configuration
 

MINI MCR-2-TC-UI - Thermocouple measuring transducer

2902055
Configurable temperature transducer with plug-in connection technology for connecting thermocouples. Configurable via DIP switch or software. Screw connection technology, standard configuration
 

MINI MCR-2-UNI-UI-UIRO - Signal conditioner

2902026
Universally configurable 4-way signal conditioner, with switching output and plug-in connection technology for the electrical isolation of analog signals. Configurable via DIP switch or software. Screw connection technology, standard configuration.
 

MINI MCR-2-UNI-UI-2UI-C - Signal duplicator

2905025
Universally configurable 4-way signal duplicator, with plug-in connection technology for the electrical isolation and duplication of analog signals. Configurable via DIP switch or software. Screw connection technology, order configuration.
 

MINI MCR-SL-F-UI-NC - Frequency transducer

2902832
The configurable frequency transducer is suitable for the connection of NAMUR proximity sensors as well as for sensors with NPN and PNP outputs. Configurable via DIP switch and teach-in wheel. Screw connection, standard configuration.
 

MINI MCR-2-UI-FRO-PT - Frequency transducer

2902032
Analog frequency transducer with limit value functionality and plug-in connection technology for converting standard signals into frequency or PWM signals. Configurable via DIP switch or software. Push-in connection technology, standard configuration.
 

MINI MCR-2-RTD-UI-C - Resistance thermometer measuring transducer

2902048
Configurable temperature transducer with plug-in connection technology for connecting 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Configurable via DIP switch or software. Screw connection technology, order configuration
 

MINI MCR-2-F-UI-PT - Frequency transducer

2902058
Universally configurable frequency transducer for converting frequency (Hz/rpm) and PWM signals into standard signals. Sensor voltages greater than 8.2 V DC are possible in combination with MINI MCR-2-SPS-PT 1033201. Push-in connection technology.
 

MINI MCR-SL-UI-F - Frequency transducer

2864082
Analog frequency transducers for converting analog standard signals into frequency signals or PWM signals, configurable via DIP switch, with screw connection
 

MINI MCR-SL-SHUNT-UI-NC - Signal conditioner

2810780
MCR 3-way isolating amplifier, with configurable input/output, for electrical isolation and conversion of analog signals in the mV range, single-pos. as well as 2-pos. with screw connection, pre-configured
 

MINI MCR-2-U-UI-PT - Signal conditioner

2902021
3-way signal conditioner, with configurable input/output, for electrical isolation and conversion of analog signals in the mV and V range, unipolar as well as bipolar. Push-in connection technology, standard configuration.
 

MINI MCR-2-I-I-ILP-PT - Loop-powered isolators

2901995
1-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
 

MINI MCR-SL-U-U - Signal conditioner

2864684
MCR 3-way isolating amplifier, for electrical isolation of analog signals, with screw connection, input signal: 0 ... 10 V/±10 V, output signal: 0 ... 10 V/±10 V
 

MINI MCR-2-UI-REL - Limit value switches

2902033
Universally configurable threshold value switch with changeover contact relay output and plug-in connection technology for switching analog limit values. Configurable via DIP switch or software. Screw connection technology, standard configuration.
 

MINI MCR-2-2I-2I-ILP-PT - Loop-powered isolators

2901997
2-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
 

MINI MCR-2-U-I0 - Signal conditioner

2902022
3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 0 V ... 10 V, output signal: 0 mA ... 20 mA, screw connection technology
 

MINI MCR-2-I4-U - Signal conditioner

2902002
3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 4 mA ... 20 mA, output signal: 0 V ... 10 V, screw connection technology
 

MINI MCR-2-RPS-2I-2I-OLP-PT - Repeater power supply

2906449
Two-channel output loop-powered 2-way repeater power supply with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
 

MINI MCR-2-T-REL-PT - Limit value switches

2905633
Universally configurable temperature limit value switch with N/O relay output for the connection of 2, 3, and 4-conductor resistance thermometers and thermocouples. Configurable via DIP switch or software. Push-in connection technology
 

MINI MCR-2-NAM-2RO - Isolation amplifier

2902004
Configurable NAMUR signal conditioner with plug-in connection technology for proximity sensors, floating switch contacts, and switch contacts with resistance circuit. 2 transistor outputs, configurable via DIP switch. Screw connection technology.
 

MINI MCR-2-U-I0-PT - Signal conditioner

2902023
3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 0 V ... 10 V, output signal: 0 mA ... 20 mA, push-in connection technology
 

MINI MCR-SL-U-I-0 - Signal conditioner

2813512
MCR 3-way isolating amplifier, for electrical isolation of analog signals, with screw connection, input signal: 0 V ... 10 V, output signal: 0 mA ... 20 mA
 

MINI MCR-2-U-U-PT - Signal conditioner

2902043
3-way signal conditioner with plug-in connection technology for the electrical isolation of unipolar and bipolar analog signals. Input signal: 0 ... 10 V/±10 V, output signal: 0 ... 10 V/±10 V, push-in connection technology.
 

MINI MCR-2-NAM-2RO-PT - Isolation amplifier

2902005
Configurable NAMUR signal conditioner with plug-in connection technology for proximity sensors, floating switch contacts, and switch contacts with resistance circuit. 2 transistor outputs. Configurable via DIP switch. Push-in connection technology.
 

MINI MCR-SL-NAM-2RNO - Switching amplifier

2864105
Configurable NAMUR switching amplifier for proximity sensors, floating switching contacts and switching contacts with resistance circuit. On the output side 2 N/O contact, with screw connection
 

MINI MCR-2-RPS-I-I-OLP-PT - Repeater power supply

2906447
1-channel output loop-powered 2-way repeater power supply with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
 

MINI MCR-2-U-I4 - Signal conditioner

2902029
3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 0 V ... 10 V, output signal: 4 mA ... 20 mA, screw connection technology
 

MINI MCR-2-UNI-UI-2UI-PT-C - Signal duplicator

2905027
Universally configurable 4-way signal duplicator, with plug-in connection technology for the electrical isolation and duplication of analog signals. Configurable via DIP switch or software. Push-in connection technology, order configuration.
 

MINI MCR-2-TC-UI-PT - Thermocouple measuring transducer

2905249
Configurable temperature transducer with plug-in connection technology for connecting thermocouples. Configurable via DIP switch or software. Push-in connection technology, standard configuration
 

MINI MCR-2-2I-2I-ILP - Loop-powered isolators

2901996
2-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Screw connection technology.
 

MINI MCR-2-SPS-24-15 - Constant voltage source

1033202
Constant voltage source with pluggable connection technology for the generation of a highly precise constant voltage of 15 V and for the supply of sensors without internal power supply. Screw connection technology.
 

MINI MCR-2-RPS-2I-2I-OLP - Repeater power supply

2906448
Two-channel output loop-powered 2-way repeater power supply with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Screw connection technology.
 

MINI MCR-2-T-2RO-PT - Limit value switches

2906877
Universally configurable temperature limit value switch with two transistor outputs for the connection of 2, 3, and 4-conductor resistance thermometers and thermocouples. Configurable via DIP switch or software, push-in connection technology
 

MINI MCR-SL-U-I-4 - Signal conditioner

2813525
MCR 3-way isolating amplifier, for electrical isolation of analog signals, with screw connection, input signal: 0 V ... 10 V, output signal: 4 mA ... 20 mA
 

MINI MCR-2-U-UI - Signal conditioner

2902019
3-way signal conditioner, with configurable input/output, for electrical isolation and conversion of analog signals in the mV and V range, unipolar as well as bipolar. Screw connection technology, standard configuration.
 

MINI MCR-2-CVCS - Constant voltage source

2902064
Constant voltage/current source with plug-in connection technology, input voltage: 9.6 V DC ... 30 V DC. Output voltage: 1.25 V ... 10 V DC or output current: 2.5 mA ... 20 mA can be set. Configurable via DIP switch. Screw connection technology.
 

MACX MCR-SL-I-I-HV-ILP-SP - Loop-powered isolators

2907705
1-channel input loop-powered 2-way isolator with increased isolating voltage and plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
 

MACX MCR-SL-2I-2I-HV-ILP-SP - Loop-powered isolators

2907707
Two-channel input loop-powered 2-way isolator with increased cut-off voltage and plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
 

MINI MCR-2-UNI-UI-UIRO-PT - Signal conditioner

2902028
Universally configurable 4-way signal conditioner, with switching output and plug-in connection technology for the electrical isolation of analog signals. Configurable via DIP switch or software. Push-in connection technology, standard configuration.
 

MINI MCR-2-UI-UI-PT-C - Signal conditioner

2902039
3-way signal conditioner with plug-in connection technology and calibrated measuring range changeover for the electrical isolation of unipolar and bipolar analog signals. Input/output configurable via DIP switch. push-in connection technology, order configuration.
 

MINI MCR-2-T-REL - Limit value switches

2905632
Universally configurable temperature limit value switch with N/O relay output for the connection of 2, 3, and 4-conductor resistance thermometers and thermocouples. Configurable via DIP switch or software, screw connection technology
 

MINI MCR-2-UI-FRO - Frequency transducer

2902031
Analog frequency transducer with limit value functionality and plug-in connection technology for converting standard signals into frequency or PWM signals. Configurable via DIP switch or software. Screw connection technology, standard configuration.
 

MACX MCR-SL-I-I-HV-ILP - Loop-powered isolators

2907704
1-channel input loop-powered 2-way isolator with increased isolating voltage and plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Screw connection technology.
 

MINI MCR-2-T-2RO - Limit value switches

2906876
Universally configurable temperature limit value switch with two transistor outputs for the connection of 2, 3, and 4-conductor resistance thermometers and thermocouples. Configurable via DIP switch or software, screw connection technology
 

MINI MCR-2-UI-FRO-C - Frequency transducer

2906201
Analog frequency transducer with limit value functionality and plug-in connection technology for converting standard signals into frequency or PWM signals. Configurable via DIP switch or software. Screw connection technology, order configuration.
 

MINI MCR-2-POT-UI-C - Resistance/potiposition transducer

2905005
Configurable potiposition transducer with plug-in connection technology for connecting potentiometers from 0 Ω ... 100 Ω to 0 kΩ ... 100 kΩ. Configurable via DIP switch or software. Screw connection technology, order configuration
 

MINI MCR-2-F-UI-PT-C - Frequency transducer

2902059
Universally configurable frequency transducer for converting frequency (Hz/rpm) and PWM signals into standard signals. Sensor voltages greater than 8.2 V DC are possible in combination with MINI MCR-2-SPS-PT 1033201. Push-in connection technology, order configuration.
 

MINI MCR-2-U-UI-PT-C - Signal conditioner

2902020
3-way signal conditioner, with configurable input/output, for electrical isolation and conversion of analog signals in the mV and V range, unipolar as well as bipolar. Push-in connection technology, order configuration.
 

MACX MCR-SL-2I-2I-HV-ILP - Loop-powered isolators

2907706
Two-channel input loop-powered 2-way isolator with increased cut-off voltage and plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Screw connection technology
 

MINI MCR-2-SPS-24-15-PT - Constant voltage source

1033201
Constant voltage source with pluggable connection technology for the generation of a highly precise constant voltage of 15 V and for the supply of sensors without internal power supply. Push-in connection technology.
 

MINI MCR-SL-I-U-0 - Signal conditioner

2813541
MCR 3-way isolating amplifier, for electrical isolation of analog signals, with screw connection, input signal: 0 mA ... 20 mA, output signal: 0 V ... 10 V
 

MINI MCR-2-CVCS-PT - Constant voltage source

2902065
Constant voltage/current source with plug-in connection technology, input voltage: 9.6 V DC ... 30 V DC. Output voltage: 1.25 V DC ...10 V DC or output current: 2.5 mA ... 20 mA can be set. Configurable via DIP switch. Push-in connection technology.
 

MINI MCR-2-TC-UI-C - Thermocouple measuring transducer

2902053
Configurable temperature transducer with plug-in connection technology for connecting thermocouples. Configurable via DIP switch or software. Screw connection technology, order configuration
 

MINI MCR-2-UI-I-OLP - Loop-powered isolators

2902061
Output loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of unipolar and bipolar analog signals. Input configurable via DIP switch. Screw connection technology, standard configuration.
 

MINI MCR-2-UNI-UI-UIRO-C - Signal conditioner

2902024
Universally configurable 4-way signal conditioner, with switching output and plug-in connection technology for the electrical isolation of analog signals. Configurable via DIP switch or software. Screw connection technology, order configuration.
 

MINI MCR-2-UI-I-OLP-PT-C - Loop-powered isolators

2902062
Output loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of unipolar and bipolar analog signals. Input configurable via DIP switch. Push-in connection technology, order configuration.
 

MINI MCR-2-U-UI-C - Signal conditioner

2902018
3-way signal conditioner, with configurable input/output, for electrical isolation and conversion of analog signals in the mV and V range, unipolar as well as bipolar. Screw connection technology, order configuration.
 

MINI MCR-2-F-UI-C - Frequency transducer

2902057
Universally configurable frequency transducer for converting frequency (Hz/rpm) and PWM signals into standard signals. Sensor voltages greater than 8.2 V DC are possible in combination with MINI MCR-2-SPS 1033202. Screw connection technology, order configuration.
 

MINI MCR-2-I0-U - Signal conditioner

2902000
3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 0 mA ... 20 mA, output signal: 0 V ... 10 V, screw connection technology
 

MINI MCR-2-RTD-UI-PT-C - Resistance thermometer measuring transducer

2902051
Configurable temperature transducer with plug-in connection technology for connecting 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Configurable via DIP switch or software. push-in connection technology, order configuration
 

MINI MCR-2-UI-I-OLP-PT - Loop-powered isolators

2902063
Output loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of unipolar and bipolar analog signals. Input configurable via DIP switch. Push-in connection technology, standard configuration.
 

MINI MCR-2-UI-REL-C - Limit value switches

2909886
Universally configurable threshold value switch with changeover contact relay output and plug-in connection technology for switching analog limit values. Configurable via DIP switch or software. Screw connection technology, order configuration.
 

MINI MCR-2-I0-U-PT - Signal conditioner

2902001
3-way signal conditioner with plug-in connection technology for the electrical isolation of analog signals. Input signal: 0 mA ... 20 mA, output signal: 0 V ... 10 V, Push-in connection technology
 

MINI MCR-2-UI-I-OLP-C - Loop-powered isolators

2902060
Output loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of unipolar and bipolar analog signals. Input configurable via DIP switch. Screw connection technology, order configuration.
 

MINI MCR-2-RPS-I-I-OLP - Repeater power supply

2906446
1-channel output loop-powered 2-way repeater power supply with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Screw connection technology.
 

MINI MCR-2-UI-REL-PT-C - Limit value switches

2909887
Universally configurable threshold value switch with changeover contact relay output and plug-in connection technology for switching analog limit values. Configurable via DIP switch or software. Push-in connection technology, order configuration.
 

MINI MCR-2-UI-FRO-PT-C - Frequency transducer

2906202
Analog frequency transducer with limit value functionality and plug-in connection technology for converting standard signals into frequency or PWM signals. Configurable via DIP switch or software. Push-in connection technology, order configuration.
 

MINI MCR-2-TC-UI-PT-C - Thermocouple measuring transducer

2905248
Configurable temperature transducer with plug-in connection technology for connecting thermocouples. Configurable via DIP switch or software. Push-in connection technology, order configuration
 

MINI MCR-2-POT-UI-PT-C - Resistance/potiposition transducer

2905006
Configurable potiposition transducer with plug-in connection technology for connecting potentiometers from 0 Ω ... 100 Ω to 0 kΩ ... 100 kΩ. Configurable via DIP switch or software. Push-in connection technology, order configuration
 

MINI MCR-2-UNI-UI-UIRO-PT-C - Signal conditioner

2902027
Universally configurable 4-way signal conditioner, with switching output and plug-in connection technology for the electrical isolation of analog signals. Configurable via DIP switch or software. Push-in connection technology, order configuration.