Bộ khuếch đại cách ly Power/Input Phoenix Contact MACX MCR-EX-SL-RPSSI-I - 2865340

THÔNG TIN THAM KHẢO

• Danh mục Model sản phẩm PHOENIX CONTACT

• 

  Tìm hiểu về điều hòa, lọc nhiểu, khuếch đại, chuyển đổi tín hiệu điều khiển và đo lường MCR

• Xem thêm

Bộ khuếch đại cách ly Power/Input Phoenix Contact MACX MCR-EX-SL-RPSSI-I - 2865340

Bộ cấp nguồn khuếch đại và điều hòa tín hiệu đầu vào Ex i, HART-transparent. Truyền tín hiệu được cung cấp hoặc tín hiệu 0/4… 20mA chủ động từ khu vực Ex đến tải (chủ động hoặc thụ động) trong khu vực an toàn. Cách ly điện 3-chiều, SIL 2 phù hợp với IEC 61508, với kết nối vít.

 

Thông số kỹ thuật

Chú ý

Utilization restriction
EMC note	EMC: class A product, see manufacturer's declaration in the download area

 

Thuộc tính về sản phẩm

Product type	Repeater power supplies
Application	Analog IN
No. of channels	1
Type	Ex i signal conditioners with SIL functional safety
Insulation characteristics
Overvoltage category	II
Pollution degree	2

 

Thông số về điện

No. of channels	1
Electrical isolation	3-way isolation
Electrical isolation between input and output	yes
Maximum power diss ipation for nominal condition	0.95 W (20 mA, 250 Ω)
Signal transmission behavior	In = Out
Step response (10-90%)	< 200 µs (for jump 4 mA ... 20 mA, load 600 Ω)
	< 600 µs (for jump 0 mA ... 20 mA, load 600 Ω)
Maximum temperature coefficient	< 0.01 %/K
Temperature coefficient, typical	< 0.004 %/K
Maximum transmission error	< 0.1 % (of final value)
Transmission error, typical	< 0.05 % (of final value)
Reverse polarity protection	yes
Electrical isolation Input/output/power supply
Rated insulation voltage	300 Vrms
Test voltage	2.5 kV AC (50 Hz, 60 s)
Insulation	Safe isolation in accordance with IEC/EN 61010-1
Electrical isolation Input/output
Electrical isolation	375 VPP (Peak value in accordance with IEC/EN 60079-11)
	265 V AC/DC (Peak value in accordance with IEC/EN 60079-11)
Electrical isolation Input/power supply
Electrical isolation	375 VPP (Peak value in accordance with IEC/EN 60079-11)
	265 V AC/DC (Peak value in accordance with IEC/EN 60079-11)
Electrical isolation Output/supply
Electrical isolation	265 V AC/DC (Peak value in accordance with IEC/EN 60079-7)
Supply
Designation	Repeater power supply operation
Nominal supply voltage	24 V DC
Supply voltage range	19.2 V DC ... 30 V DC (24 V DC, -20 % ... +25 %)
Max. current consumption	< 76 mA (24 V DC / 20 mA / 1000 Ω)
	< 55 mA (24 V DC / 20 mA / 250 Ω)
Power dissipation	< 1.1 W (24 V DC / 20 mA / 1000 Ω)
	< 0.95 W (24 V DC / 20 mA / 250 Ω)
	< 1.2 W (24 V DC / 20 mA / 0 Ω)
Power consumption	< 1.8 W (20 mA / 1000 Ω)
	< 1.3 W (20 mA / 250 Ω)
Supply
Designation	Signal conditioner operation
Nominal supply voltage	24 V DC
Supply voltage range	19.2 V DC ... 30 V DC (24 V DC, -20 % ... +25 %)
Max. current consumption	< 44 mA (24 V DC / 20 mA / 1000 Ω)
	< 27 mA (24 V DC / 20 mA / 250 Ω)
Power dissipation	< 0.75 W (24 V DC / 20 mA / 1000 Ω)
	< 0.65 W (24 V DC / 20 mA / 250 Ω)
	< 0.95 W (24 V DC / 20 mA / 0 Ω)

 

Thông số đầu vào

Signal
Description of the input	Active current input, intrinsically safe
Number of inputs	1
Input signal	Current
Current input signal	4 mA ... 20 mA
Current limitation	25 mA
Transmitter supply voltage	> 16 V (20 mA)
	> 15.3 V (22.5 mA)
Polarization and surge protection	Yes
Underload/overload signal range	0 mA ... 24 mA (Extended transmission range for diagnostics)
Signal
Description of the input	Passive current input, intrinsically safe
Current input signal	0 mA ... 20 mA
	4 mA ... 20 mA
Voltage drop	< 3.5 V (in input isolating amplifier operation)
Underload/overload signal range	0 mA ... 24 mA (Extended transmission range for diagnostics)

 

Thông số đầu ra

Signal: Repeater power supply operation
Output description	Current output (active and passive)
Number of outputs	1
Current output signal	4 mA ... 20 mA (active)
	4 mA ... 20 mA (14 ... 26 V ext. source voltage)
Load/output load current output	< 1000 Ω (20 mA)
	< 825 Ω (24 mA)
Output ripple	< 20 mVrms
Output behavior in the event of an error	0 mA (Cable break in the input)
	≥ 22.5 mA (Cable short-circuit in the input)
Underload/overload signal range	0 mA ... 24 mA (Extended transmission range for diagnostics)
Signal: Signal conditioner operation
Output description	Current output (active and passive)
Current output signal	0 mA ... 20 mA (active)
	4 mA ... 20 mA (active)
	0 mA ... 20 mA (14 ... 26 V ext. source voltage)
	4 mA ... 20 mA (14 ... 26 V ext. source voltage)
Load/output load current output	< 1000 Ω (20 mA)
	< 825 Ω (24 mA)
Output ripple	< 20 mVrms
Output behavior in the event of an error	0 mA (Cable break in the input)
	0 mA (Cable short-circuit in the input)
Underload/overload signal range	0 mA ... 24 mA (Extended transmission range for diagnostics)

 

Thông số kết nối

Connection method	Screw connection
Stripping length	7 mm
Screw thread	M3
Conductor cross section solid	0.2 mm² ... 2.5 mm²
Conductor cross section flexible	0.2 mm² ... 2.5 mm²
Conductor cross section AWG	24 ... 14
Tightening torque	0.5 Nm ... 0.6 Nm
Test socket
Max. diameter	2 mm

 

Thông số Ex

Safety data: Repeater power supply operation
Max. output voltage Uo	25.2 V
Max. output current Io	93 mA
Max. output power Po	587 mW
Safety-related maximum voltage Um	253 V AC (≤ 2000 m)
	125 V DC (≤ 2000 m)
I (simple circuit): Max. external inductivity Lo / Max. external capacitance Co	40 mH / 4.8 µF
IIA (simple circuit): Max. external inductivity Lo / Max. external capacitance Co	26 mH / 2.9 µF
IIB (simple circuit): Max. external inductivity Lo / Max. external capacitance Co	14 mH / 820 nF
IIC (simple circuit): Max. external inductivity Lo / Max. external capacitance Co	3 mH / 107 nF
IIA (mixed circuit): Max. external inductivity Lo / Max. external capacitance Co	26 mH / 470 nF, 20 mH / 570 nF, 1 mH / 630 nF, 0.5 mH / 720 nF, 0.1 mH / 1.1 µF, 0.005 mH / 2.9 µF
IIB/III (mixed circuit): Max. external inductivity Lo / Max. external capacitance Co	16 mH / 370 nF, 500 µH / 510 nF, 200 µH / 660 nF, 100 µH / 820 nF
IIC (mixed circuit): Max. external inductivity Lo / Max. external capacitance Co	2.2 mH / 47 nF, 2 mH / 49 nF, 1 mH / 63 nF, 500 µH / 80 nF, 200 µH / 107 nF
I (mixed circuit): Max. external inductivity Lo / Max. external capacitance Co	37 mH / 0.54 µF, 0.35 mH / 1 µF, 0.009 mH / 2.9 µF, 0.001 mH / 4.15 µF
Safety data: Signal conditioner operation
Input voltage Ui	≤ 30 V
Input current Ii	≤ 150 mA
Max. internal inductance Li	negligible
Max. internal capacitance Ci	negligible
Safety-related maximum voltage Um	253 V AC (≤ 2000 m)
	125 V DC (≤ 2000 m)
Safety data: Repeater power supply operation
Max. output voltage Uo	25.2 V
Max. output current Io	93 mA
Max. output power Po	587 mW
Safety-related maximum voltage Um	253 V AC (≤ 2000 m)
	125 V DC (≤ 2000 m)
I (simple circuit): Max. external inductivity Lo / Max. external capacitance Co	40 mH / 4.8 µF
IIA (simple circuit): Max. external inductivity Lo / Max. external capacitance Co	26 mH / 2.9 µF
IIB (simple circuit): Max. external inductivity Lo / Max. external capacitance Co	14 mH / 820 nF
IIC (simple circuit): Max. external inductivity Lo / Max. external capacitance Co	3 mH / 107 nF
IIA (mixed circuit): Max. external inductivity Lo / Max. external capacitance Co	26 mH / 470 nF, 20 mH / 570 nF, 1 mH / 630 nF, 0.5 mH / 720 nF, 0.1 mH / 1.1 µF, 0.005 mH / 2.9 µF
IIB/III (mixed circuit): Max. external inductivity Lo / Max. external capacitance Co	16 mH / 370 nF, 500 µH / 510 nF, 200 µH / 660 nF, 100 µH / 820 nF
IIC (mixed circuit): Max. external inductivity Lo / Max. external capacitance Co	2.2 mH / 47 nF, 2 mH / 49 nF, 1 mH / 63 nF, 500 µH / 80 nF, 200 µH / 107 nF
I (mixed circuit): Max. external inductivity Lo / Max. external capacitance Co	37 mH / 0.54 µF, 0.35 mH / 1 µF, 0.009 mH / 2.9 µF, 0.001 mH / 4.15 µF
Safety data: Signal conditioner operation
Input voltage Ui	≤ 30 V
Input current Ii	≤ 150 mA
Max. internal inductance Li	negligible
Max. internal capacitance Ci	negligible
Safety-related maximum voltage Um	253 V AC (≤ 2000 m)
	125 V DC (≤ 2000 m)

 

Giao diện

Data communication (bypass)
HART function	Yes
Protocols supported	HART-transparent

 

Tín hiệu LED signaling

Status display

Green LED (supply voltage)

 

Kích thước

Dimensional drawing
Width	12.5 mm
Height	112.5 mm
Depth	113.7 mm
	114.5 mm (Snapped onto DIN rail NS 35/7,5 in accordance with EN 60715)

 

Thông số vật liệu

Flammability rating according to UL 94	V0 (Housing)
Housing material	PA 6.6-FR

 

Điều kiện môi trường vận hành và Mức bảo vệ

Ambient conditions
Degree of protection	IP20 (not assessed by UL)
Ambient temperature (operation)	-20 °C ... 60 °C (Any mounting position)
Ambient temperature (storage/transport)	-40 °C ... 80 °C
Permissible humidity (operation)	10 % ... 95 % (non-condensing)

 

Approval data

CE
Certificate	CE-compliant
Note	and EN 61326
ATEX
Identification	 II (1) G [Ex ia Ga] IIC
	 II (1) D [Ex ia Da] IIIC
	 II 3(1) G Ex ec [ia Ga] IIC T4 Gc
	 I (M1) [Ex ia Ma] I
Certificate	BVS 08 ATEX E 054X
IECEx
Identification	[Ex ia Ga] IIC
	[Ex ia Da] IIIC
	Ex ec [ia Ga] IIC T4 Gc
	[Ex ia Ma] I
Certificate	IECEx BVS 08.0016X
CCC / China-Ex
Identification	[Ex ia Ga] IIC
	[Ex iaD]
	Ex nA [ia Ga] IIC T4 Gc
Certificate	NEPSI GYJ20.1309X
UL, USA / Canada
Identification	UL 61010 Listed
	Class I, Div. 2, Groups A, B, C, D T4
	Class I, Div. 2, Groups IIC, IIB, IIA T4
	Associated apparatus for use in Class I, Division 1, Groups A,B,C,D
	Associated apparatus for use in Class II, Div.1 Groups E,F,D
	Associated apparatus for use in Class III, Division 1
	Associated apparatus for use in Class I, Zone 0,1,2, Groups IIC,IIB,IIA
Certificate	, C.D.-No 83104549
UL, USA / Canada
Identification	UL 61010 Listed
	Class I Div 2; IS for Class I, II, III Div 1
Certificate	, C.D.-No 83104549
Shipbuilding approval
Certificate	DNV GL TAA000020C
Safety Integrity Level (SIL, IEC 61508)
Identification	2
Certificate	BVS PB 03/08-2
EAC Ex
Identification	 [Ex ia Ga] IIC
	 [Ex ia Da] IIIC
Certificate	RU C-DE.AB72.B.00093/19
KC-s
Identification	[Ex ia] IIC/IIB
Certificate	17-KA4BO-0400X
INMETRO
Identification	[Ex ia Ga] IIC/IIB
	[Ex ia Da] IIIC
	Ex nA [ia Ga] IIC/IIB T4 Gc
	[Ex ia Ma] I
Certificate	DNV 18.0136 X
DNV GL data
Temperature	B
Humidity	B
Vibration	A
EMC	A
Enclosure	Required protection according to the Rules shall be provided upon installation on board

 

Thông số EMC

Electromagnetic compatibility	Conformance with EMC directive
Noise emission	EN 61000-6-4
Noise immunity	EN 61000-6-2
Note	When being exposed to interference, there may be minimal deviations.
Electromagnetic HF field
Designation	Electromagnetic RF field
Standards/regulations	EN 61000-4-3
Typical deviation from the measuring range final value	1 %
Fast transients (burst)
Designation	Fast transients (burst)
Standards/regulations	EN 61000-4-4
Typical deviation from the measuring range final value	1 %
Conducted interference
Designation	Conducted interferences
Standards/regulations	EN 61000-4-6
Typical deviation from the measuring range final value	1 %

 

Quy-Chuẩn

Electrical isolation	3-way isolation
GB Standard
Standards/regulations	GB 3626.20
	GB 3836.1
	GB 3836.4
	GB 3836.8
	GB 12476.1
	GB 12476.4

 

Thông số lắp đặt

Mounting type

DIN rail mounting

 

Thông số về thương mại

Item number	2865340
Packing unit	1 pc
Minimum order quantity	1 pc
Note	Made to Order (non-returnable)
Sales Key	C03
Product Key	CK3111
Catalog Page	Page 142 (C-5-2019)
GTIN	4046356160353
Weight per Piece (including packing)	181.5 g
Weight per Piece (excluding packing)	160 g
Customs tariff number	85437090
Country of origin	DE

- Tài liệu kỹ thuật (Datasheet) Phoenix Contact MACX MCR-EX-SL-RPSSI-I - 2865340 ở đây.


Tham khảo thêm các model khác cùng loại:

MACX MCR-EX-SL-2NAM-RO - 2865476

Ex i NAMUR isolating amplifier, 2-channel. For operating proximity sensors and switches in Ex areas. The signals are transmitted via relay outputs (N/O contact) to the safe area. Line fault detection (LFD), 3-way isolation, SIL 2.
 

IFS-USB-PROG-ADAPTER - 2811271

Programming adapter with USB interface, for programming with software. The USB driver is included in the software solutions for the products to be programmed, such as measuring transducers or motor managers.
 

MACX MCR-SL-I-I-ILP - 2905278

1-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Screw connection technology.
 

MACX MCR-T-UIREL-UP - 2811378

Freely programmable temperature transducer with analog output and 3 limit value relays, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.
 

MACX MCR-SL-RPSSI-I - 2865955

Repeater power supply and input signal conditioner, HART-transparent. Transmits supplied or active 0/4 … 20 mA signals to a load (active or passive). 3-way electrical isolation, SIL 2 in accordance with IEC 61508.
 

MACX MCR-EX-SL-SD-21-60-LP - 2865515

Ex i solenoid driver. For the intrinsically safe control of Ex i solenoid valves, alarm modules or LEDs installed in the Ex area. Current limitation at 58 mA. For gases up to Group IIB, loop-powered, electrical isolation, SIL 3. Screw connection.
 

MACX MCR-PTB - 2865625

Power and fault signaling module with screw connection, including corresponding ME 17,5 TBUS 1,5/ 5-ST-3,81 GY DIN rail connector
 

MACX MCR-EX-SL-SD-24-48-LP - 2865609

Ex i solenoid driver. For the intrinsically safe control of Ex i solenoid valves, alarm modules or LEDs installed in the Ex area. Current limitation at 48 mA. For gases up to Group IIC, loop-powered, electrical isolation, SIL 3. Screw connection.
 

MACX MCR-UI-UI - 2811284

Configurable 3-way isolating amplifier with safe electrical isolation, 24 V, power bridging. DIP switches on the front, over 1600 signal conversions can be set. Order configuration, screw connection, SIL.
 

MACX MCR-T-UI-UP-C - 2811873

Freely programmable temperature transducer with analog output and 1 limit value relay, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.
 

MACX MCR-SL-I-I-HV-ILP - 2907704

1-channel input loop-powered 2-way isolator with increased isolating voltage and plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Screw connection technology.
 

MACX MCR-EX-SL-SD-21-25-LP - 2865492

Ex i solenoid driver. For the intrinsically safe control of Ex i solenoid valves, alarm modules or LEDs installed in the Ex area. Current limitation at 25 mA. For gases up to Group IIC, loop-powered, electrical isolation, SIL 3. Screw connection.
 

MACX MCR-EX-SL-NAM-NAM - 2866006

Ex i NAMUR signal conditioner. For operating Ex i proximity sensors and switches in the Ex area. Passive transistor output (resistive according to EN 60947-5-6), line fault transparency, up to SIL 2 according to IEC 61508; screw connection.
 

MACX MCR-SL-I-I-ILP-SP - 2905279

1-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
 

MACX MCR-SL-2NAM-T - 2865036

NAMUR 2-channel signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via transistor outputs (passive). Line fault detection, 3-way electrical isolation, SIL 2, screw connection.
 

MACX MCR-SL-2NAM-R-UP - 2865052

2-channel NAMUR signal conditioner with wide range power supply for proximity sensors and switches. In terms of signal output, for each channel there is a relay with a changeover contact available. Line fault detection (LFD), 3-way isolation, screw connection, SIL 2.
 

MACX MCR-T-UI-UP-SP-C - 2811970

Freely programmable temperature transducer with analog output and 1 limit value relay, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.
 

MACX MCR-EX-RTD-I-C - 1052463

Ex i temperature transducer: converts signals from resistance temperature detectors installed in the Ex area and transmits a 0/4 - 20 mA signal to a load in the safe area. Freely programmable. 3-way isolation, SIL, screw connection, order configuration.
 

MACX MCR-TC-I - 1050228

Temperature transducer: converts signals from thermocouples and mV sources into 0/4…20 mA signals. Freely programmable, 3-way electrical isolation, screw connection, SIL.
 

MACX MCR-SL-2NAM-RO-SP - 2924294

NAMUR 2-channel signal conditioner for operating proximity sensors and switches. The signals are transferred to the control level using relay outputs (N/O contact). Line fault detection, 3-way electrical isolation, SIL 2, Push-in connection.
 

MACX MCR-UI-UI-SP - 2811572

Configurable 3-way isolating amplifier with safe electrical isolation, 24 V, power bridging. DIP switches on the front, over 1600 signal conversions can be set. Order configuration, spring-cage connection, SIL.
 

MACX MCR-SL-2I-2I-HV-ILP - 2907706

Two-channel input loop-powered 2-way isolator with increased cut-off voltage and plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Screw connection technology
 

MACX MCR-SL-NAM-2T - 2865023

NAMUR signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via 2 transistor outputs (passive). Line fault detection, 3-way electrical isolation, SIL 2, screw connection.
 

MACX MCR-T-UI-UP-SP - 2811860

Freely programmable temperature transducer with analog output and 1 limit value relay, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.
 

MACX MCR-SL-2I-2I-HV-ILP-SP - 2907707

Two-channel input loop-powered 2-way isolator with increased cut-off voltage and plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
 

MACX MCR-EX-T-UI-UP-C - 2811763

Freely programmable Ex-i temperature transducer with analog output and 1 limit value relay, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.
 

MACX MCR-EX-SL-NAM-NAM-SP - 2924883

Ex i NAMUR signal conditioners. For operating Ex i proximity sensors and switches in hazardous areas. Passive transistor output (resistive according to EN  60947-5-6), line fault transparency, up to SIL 2 according to IEC 61508; Push-in connection
 

MACX MCR-EX-SL-SD-23-48-LFD - 2924867

Ex i solenoid driver for controlling Ex i solenoid valves in hazardous areas, logic input, off-load voltage 22.6 V, current limitation at 48 mA, , line fault transparency, error message output, up to SIL 3 according to IEC 61508, screw connection
 

MACX MCR-EX-SL-SD-24-48-LP-SP - 2924126

Ex i solenoid driver. For the intrinsically safe control of Ex i solenoid valves, alarm modules or LEDs installed in the Ex area. Current limitation at 48 mA. For gases up to Group IIC, loop-powered, electrical isolation, SIL 3. Push-in connection.
 

MACX MCR-SL-UI-REL - 2906169

Limit value switch with input for active current and voltage signals and a limit-value relay output (changeover contact). Can be set via DIP switch and potentiometer, galvanic 3-way electrical isolation, up to SIL2 (SC3), PLc Cat.1, screw connection.
 

MACX MCR-SL-2I-2I-ILP-SP - 2905281

2-channel input loop-powered 2-way isolator with plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
 

MACX MCR-SL-RPSS-2I-2I-SP - 2904090

2-channel repeater power supply for operating 2-conductor measuring transducers, input: 4 ... 20 mA (supplying), output: 4 ... 20 mA (active), bidirectional transmission with digital HART transparency, Push-in connection, SIL, PL.
 

MACX MCR-S-MUX - 2865599

HART Multiplexer for online configuration and diagnostics of HART-compatible field devices, as well as for continuous documentation of process variables and states with a PC or management system for mounting on NS 35/7.5 or NS 32
 

MACX MCR-UI-UI-UP - 2811459

Configurable 3-way isolating amplifier with safe electrical isolation and wide-range power supply (24 V ... 230 V AC/DC). DIP switches on the front, over 1600 signal conversions can be set. Order configuration, screw connection, SIL.
 

MACX MCR-S-MUX-TB - 2308124

The HART transfer board is used to operate the MACX-MCR-S-MUX HART multiplexer. The signals from the HART-compatible signal converters are applied to the terminal strip of the transfer board where they are then transmitted to the multiplexer via an FLK.
 

MACX MCR-1TS-I-OLP-SP - 1145196

Output loop-powered temperature transducer for transmitting RTD and TC sensor signals as well as from resistance and voltage sensors via 4 mA ... 20 mA. HART, Standard configuration, Push-in connection
 

MACX MCR-EX-TC-I-C - 1052458

Ex i temperature transducer: converts signals from thermocouples installed in Ex areas and mV sources and transmits a 0/4…20 mA signal to a load in the safe area. Order configuration, freely programmable. 3-way isolation, SIL.
 

MACX MCR-TC-I-C - 1052459

Temperature transducer: converts signals from thermocouples and mV sources into 0/4…20 mA signals. Order configuration, freely programmable, 3-way electrical isolation, screw connection, SIL.
 

MACX MCR-EX-SL-SD-23-48-LFD-SP - 2924870

Ex i solenoid driver for controlling Ex i solenoid valves in hazardous areas, logic input, off-load voltage 22.6 V, current limitation at 48 mA, , line fault transparency, error message output, up to SIL 3 according to IEC 61508, Push-in connection
 

MACX MCR-EX-T-UIREL-UP-SP-C - 2924809

Programmable temperature transducer with analog output and 3 limit value relays, intrinsically safe signal input, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.
 

MACX MCR-EX-T-UI-UP-SP-C - 2924692

Freely programmable Ex-i temperature transducer with analog output and 1 limit value relay, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.
 

MACX MCR-EX-T-UI-UP-SP - 2924689

Programmable Ex-i temperature transducer with analog output and 1 limit value relay, standard configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.
 

MACX MCR-SL-2NAM-R-UP-SP - 2924304

2-channel NAMUR signal conditioner with wide range power supply for proximity sensors and switches. In terms of signal output, for each channel there is a relay with a changeover contact available. Line fault detection (LFD), 3-way isolation, Push-in connection, SIL 2.
 

MACX MCR-SL-NAM-2T-SP - 2924278

NAMUR signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via 2 transistor outputs (passive). Line fault detection, 3-way electrical isolation, SIL 2, Push-in connection.
 

MACX MCR-SL-NAM-R-SP - 2924252

NAMUR signal conditioner for operating proximity sensors and switches. The signals are transmitted to the control level via relay output (changeover contact). Line fault detection (LFD), 3-way electrical isolation, SIL 2, with Push-in connection.
 

MACX MCR-EX-SL-SD-21-40-LP-SP - 2924139

Ex i solenoid driver. For the intrinsically safe control of Ex i solenoid valves, alarm modules or LEDs installed in the Ex area. Current limitation at 40 mA. For gases up to Group IIC, loop-powered, electrical isolation, SIL 3. Push-in connection.
 

MACX MCR-EX-SL-SD-21-25-LP-SP - 2924113

Ex i solenoid driver. For the intrinsically safe control of Ex i solenoid valves, alarm modules or LEDs installed in the Ex area. Current limitation at 25 mA. For gases up to Group IIC, loop-powered, electrical isolation, SIL 3. Push-in connection.
 

MACX MCR-EX-SL-NAM-2RO-SP - 2924061

Ex i NAMUR isolating amplifier For operating proximity sensors and switches in Ex areas. The signals are transmitted via 2 relay outputs (N/O contact) to the safe area. Line fault detection (LFD), 3-way isolation, SIL 2.
 

MACX MCR-SL-I-I-HV-ILP-SP - 2907705

1-channel input loop-powered 2-way isolator with increased isolating voltage and plug-in connection technology for the electrical isolation of analog signals. Input signal = output signal: 0(4) mA ... 20 mA. Push-in connection technology.
 

MACX MCR-SL-UI-REL-SP - 2906170

Limit value switch with input for active current and voltage signals and a limit-value relay output (changeover contact). Can be set via DIP switch and potentiometer, galvanic 3-way electrical isolation, up to SIL2 (SC3), PLc Cat.1, Push-in connection.
 

MACX MCR-EX-SL-SD-24-48-LFD-SP - 2906156

Ex i solenoid driver for controlling Ex i solenoid valves in hazardous areas, logic input, off-load voltage 24.3 V, current limitation at 48 mA, line fault transparency, error message output, up to SIL 3 according to IEC 61508, Push-in connection.
 

MACX MCR-EX-DUMMY-ISOLATOR-SP - 2905846

Dummy module with no function for connecting unused intrinsically safe signal cables, with plug-in push-in connection terminal blocks.
 

MACX MCR-EX-SL-SD-21-25-LFD-SP - 2905674

Ex i solenoid driver for controlling Ex i solenoid valves in hazardous areas, logic input, off-load voltage 21.1 V, current limitation at 25.1 mA, line fault transparency, error message output, up to SIL 3 according to IEC 61508; Push-in connection.
 

MACX MCR-EX-SL-SD-21-25-LFD - 2905669

Ex i solenoid driver for controlling Ex i solenoid valves in hazardous areas, logic input, off-load voltage 21.1 V, current limitation at 25.1 mA, line fault transparency, error message output, up to SIL 3 according to IEC 61508; screw connection.
 

MACX MCR-EX-DUMMY-ISOLATOR - 2904970

Dummy module with no function for connecting unused intrinsically safe signal cables, with plug-in screw connection terminal blocks.
 

MACX MCR-EX-T-UIREL-UP-C - 2865722

Programmable temperature transducer with analog output and 3 limit value relays, intrinsically safe signal input, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.
 

MACX MCR-T-UIREL-UP-SP-C - 2811831

Freely programmable temperature transducer with analog output and 3 limit value relays, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, Push-in connection, SIL, PL.
 

MACX MCR-UI-UI-UP-SP - 2811585

Configurable 3-way isolating amplifier with safe electrical isolation and wide-range power supply (24 V ... 230 V AC/DC). DIP switches on the front, over 1600 signal conversions can be set. Order configuration, spring-cage connection, SIL.
 

MACX MCR-T-UIREL-UP-C - 2811514

Freely programmable temperature transducer with analog output and 3 limit value relays, order configuration, resistance thermometer in 2-, 3-, or 4-conductor technology, thermocouples, electrical isolation, wide-range power supply, screw connection, SIL, PL.
 

MACX MCR-EX-1TS-I-OLP - 1145365

Ex i, Output loop-powered temperature transducer for transmitting RTD and TC sensor signals as well as from resistance and voltage sensors via 4 mA ... 20 mA. HART, Standard configuration, Screw connection
 

ME 6,2 TBUS-PR-ADAPTER - 1136500

Power rail adapter (ME 6,2 TBUS-PR-ADAPTER), 2-pos., enables MINI and MACX Analog modules to be adapted for supply via universal power rail UPR-03 and UPR-05.
 

MACX MCR-EX-RTD-I-SP-C - 1052652

Ex i temperature transducer: converts signals from resistance temperature detectors installed in the Ex area and transmits a 0/4 - 20 mA signal to a load in the safe area. Freely programmable, 3-way isolation, SIL, Push-in connection, order configuration.
 

MACX MCR-RTD-I-C - 1052472

Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, screw connection, SIL, 3-way electrical isolation, order configuration.
 

MACX MCR-RTD-I-SP-C - 1052464

Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, Push-in connection, SIL, 3-way electrical isolation, order configuration.
 

MACX MCR-EX-TS-I-OLP-C - 1012248

Ex i, Output loop-powered temperature transducer for transmitting up to 2 sensor signals from RTD and TC sensors, as well as from resistance and voltage sensors via 4 mA ... 20 mA. HART, Order configuration, Safety Integrity Level (SIL, IEC 61508): 2, Systematic Capability: 3, Screw connection