Bộ khuếch đại tín hiệu nguồn Phoenix Contact MINI MCR-2-RPSS-I-I-PT - 2902015

THÔNG TIN THAM KHẢO

• Danh mục Model sản phẩm PHOENIX CONTACT

• 

  Tìm hiểu về điều hòa, lọc nhiểu, khuếch đại, chuyển đổi tín hiệu điều khiển và đo lường MCR

• Xem thêm

Bộ khuếch đại tín hiệu nguồn Phoenix Contact MINI MCR-2-RPSS-I-I-PT - 2902015

3-way repeater power supply with plug-in connection technology. HART-transparent, input signal 0(4) mA ... 20 mA, output signal 0(4) mA ... 20 mA. The device can be used in both isolator and repeater power supply operation. push-in connection technology

 

 

Mô tả

Bộ cấp nguồn lặp lại với công nghệ kết nối plug-in cung cấp cho bộ phát tại hiện trường và cách ly tín hiệu đầu vào khỏi tín hiệu đầu ra về mặt điện. Giao thức dữ liệu HART có thể được truyền hai chiều. Thiết bị có thể được sử dụng trong cả hoạt động cung cấp điện của bộ cách ly và bộ lặp. Tín hiệu tương tự tiêu chuẩn 0 ... 20 mA hoặc 4 ... 20 mA cách điện có sẵn ở phía đầu vào và đầu ra với tải đầu ra tối đa là 600 Ω. Đầu dò đo hỗ trợ giám sát lỗi và giao tiếp NFC./ The repeater power supply with plug-in connection technology supplies the transmitter in the field and electrically isolates the input signal from the output signal. HART data protocols can be transmitted bidirectionally. The device can be used in both isolator and repeater power supply operation. Electrically isolated 0 ... 20 mA or 4 ... 20 mA standard analog signals are available on the input and output sides with a maximum output load of 600 Ω. The measuring transducer supports fault monitoring and NFC communication.

 

Thông số kỹ thuật

Notes

Utilization restriction
EMC note	EMC: class A product, see manufacturer's declaration in the download area

 

Product properties

Product type	Repeater power supplies
Product family	MINI Analog Pro
No. of channels	1
Type	Signal conditioner
Insulation characteristics: GB Standard
Overvoltage category	II
Pollution degree	2

 

Electrical properties

No. of channels	1
Electrical isolation	3-way isolation
Electrical isolation between input and output	yes
Limit frequency (3 dB)	> 1.75 kHz
Protective circuit	Transient protection
Signal transmission behavior	In = Out
Step response (10-90%)	< 200 µs (typ.)
Maximum temperature coefficient	0.0075 %/K
Temperature coefficient, typical	0.0075 %/K
Maximum transmission error	0.05 % (of final value in repeater power supply operation)
	0.1 % (of final value in isolator operation)
Electrical isolation Input/output/power supply
Rated insulation voltage	300 Vrms
Test voltage	3 kV AC (50 Hz, 60 s)
Insulation	Reinforced insulation according to IEC/EN 61010-1
Supply
Nominal supply voltage	24 V DC
Supply voltage range	9.6 V DC ... 30 V DC (The DIN rail connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, item no. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail in accordance with EN 60715)
Typical current consumption	25 mA (at 24 V DC and in isolator operation)
	50 mA (at 24 V DC and in repeater power supply operation)
	55 mA (at 12 V DC and in isolator operation)
	110 mA (at 12 V DC and in repeater power supply operation)
Power consumption	≤ 1400 mW (at IOUT = 20 mA, 9.6 V DC, 600 Ω load)

 

Input data

Signal: Current
Description of the input	Sensor circuit
Number of inputs	1
Current input signal	0 mA ... 20 mA (isolator operation)
	4 mA ... 20 mA (repeater power supply and isolator operation)
Input resistance current input	 68 Ω (+0.7 V for test diode)
Transmitter supply voltage	> 19.5 V

 

Output data

Signal: Current
Number of outputs	1
Non-load voltage	< 20 V
Current output signal	0 mA ... 20 mA (isolator operation)
	4 mA ... 20 mA (repeater power supply and isolator operation)
Max. current output signal	24 mA
Load/output load current output	≤ 600 Ω (20 mA)
Ripple	< 20 mVPP (600 Ω)

 

Connection data

Connection method	Push-in connection
Stripping length	10 mm
Conductor cross section rigid	0.2 mm² ... 2.5 mm² (with ferrule)
	0.14 mm² ... 2.5 mm² (without ferrule)
Conductor cross section flexible	0.14 mm² ... 2.5 mm²
Conductor cross section AWG	24 ... 12 (flexible)

 

Ex data

Ex installation (EPL)	Gc
	Div. 2

 

Interfaces

Data communication (bypass)
HART function	Yes
Limit frequency (3 dB)	 1.75 kHz

 

Signaling

Status display

Green LED (supply voltage)

 

Dimensions

Width	6.2 mm
Height	109.81 mm
Depth	119.2 mm

 

Material specifications

Fire protection for rail vehicles (DIN EN 45545-2) R22	HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R23	HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R24	HL 1 - HL 2
Housing material	PBT

 

Environmental and real-life conditions

Ambient conditions
Degree of protection	IP20 (not assessed by UL)
Ambient temperature (operation)	-40 °C ... 70 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Altitude	≤ 2000 m
Permissible humidity (operation)	5 % ... 95 % (non-condensing)

 

Approvals

CE
Certificate	CE-compliant
ATEX
Identification	 II 3 G Ex ec IIC T4 Gc
Certificate	BVS 19 ATEX E 047 X
UKCA Ex (UKEX)
Identification	 II 3 G Ex ec IIC T4 Gc
Certificate	PxCIF21UKEX2902000X
IECEx
Identification	Ex ec IIC T4 Gc
Certificate	IECEx BVS 19.0041X
CCC / China-Ex
Identification	Ex nA IIC T4 Gc
UL, USA/Canada
Identification	UL 508 Listed
	Class I, Div. 2, Groups A, B, C, D T5
	Class I, Zone 2, Group IIC T5
Shipbuilding approval
Certificate	DNV GL TAA00002UA
EAC Ex
Identification	 2Ex ec IIC T4 Gc
Certificate	BY/112 02.01 TP012 103.01 00079
DNV GL data
Temperature	B
Humidity	B
Vibration	A
EMC	A
Enclosure	Required protection according to the Rules shall be provided upon installation on board

 

EMC data

Noise immunity	EN 61000-6-2
Note	When being exposed to interference, there may be minimal deviations.
Electromagnetic compatibility	Conformance with EMC directive
Noise emission	EN 61000-6-4
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Comments	Safety measures must be taken to prevent electrostatic discharge.
Electromagnetic HF field
Designation	Electromagnetic RF field
Standards/regulations	EN 61000-4-3
Fast transients (burst)
Designation	Fast transients (burst)
Standards/regulations	EN 61000-4-4
Surge current load (surge)
Standards/regulations	EN 61000-4-5
Conducted interference
Designation	Conducted interferences
Standards/regulations	EN 61000-4-6

 

Standards and regulations

Electrical isolation	3-way isolation
GB Standard
Standards/regulations	GB 3836.1
	GB 3836.8

 

Mounting

Mounting type	DIN rail mounting
Assembly instructions	The DIN rail connector can be used for bridging the supply voltage. It can be snapped onto a 35 mm EN 60715 DIN rail.
Mounting position	any

 

Commercial data

Item number	2902015
Packing unit	1 pc
Minimum order quantity	1 pc
Product key	CK1411
Catalog page	Page 77 (C-5-2019)
GTIN	4046356649544
Weight per piece (including packing)	118 g
Weight per piece (excluding packing)	88 g
Customs tariff number	85437090
Country of origin	DE

 

Classifications

ECLASS

ECLASS-11.0	27210120
ECLASS-12.0	27210120
ECLASS-13.0	27210120

 

ETIM

ETIM 9.0

EC002653

 

UNSPSC

UNSPSC 21.0

39121000

 

Approvals

DNV GL

Approval ID: TAA00002UA
 

UL Listed

Approval ID: FILE E 238705
 

CCC

Approval ID: 2021322303003858
 

cUL Listed

Approval ID: FILE E 238705
 

IECEx

Approval ID: IECEx BVS 19.0041X
 

cUL Listed

Approval ID: FILE E 196811
 

UL Listed

Approval ID: FILE E 196811
 

ATEX

Approval ID: BVS 19 ATEX E 047 X
 

cULus Listed

 

cULus Listed

 

Environmental product compliance

REACh SVHC	Lead 7439-92-1
China RoHS	Environmentally Friendly Use Period = 50 years
	For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads”

- Tài liệu kỹ thuật Phoenix Contact MINI MCR-2-RPSS-I-I-PT - 2902015 ở đây.

 

Accessories

ME 6,2 TBUS-2 1,5/5-ST-3,81 GY - DIN rail bus connectors
2695439

ME 6,2 TBUS-2 1,5/5-ST-3,81 GN - DIN rail bus connectors
2869728

GW HART USB MODEM - Cable adapter
1003824

TC-D37SUB-AIO16-MP-PS-UNI - Module carrier
2906640

TC-D37SUB-ADIO16-MP-P-UNI - Module carrier
2906639

MINI MCR-2-V8-FLK 16 - System adapter
2901993

MINI MCR-2-V8-MOD-RTU - Communication module
2905634

MINI MCR-2-V8-MOD-TCP - Communication module
2905635

MINI MCR-2-V8-PB-DP - Communication module
2905636

MINI MCR-2-V8-PN - Communication module
2905637

FASTCON PRO-SET - Connector set
2906227

FASTCON PRO-SET-PT - Connector set
2906228

UCT-EM (30X5) - Marker for end clamp
0801505

UCT-EM (30X5) CUS - Marker for end clamp
0801589

SK 5,0 WH:REEL - Marker strip
0805221

UC-EMLP (15X5) - Plastic label
0819301

UC-EMLP (15X5) YE - Plastic label
0822615

UC-EMLP (15X5) CUS - Plastic label
0824550

UC-EMLP (15X5) YE CUS - Plastic label
0824551

UC-EMLP (15X5) SR - Plastic label
0828095

UC-EMLP (15X5) SR CUS - Plastic label
0828099

US-EMLP (15X5) - Plastic label
0828790

US-EMLP (15X5) YE - Plastic label
0828873

US-EMLP (15X5) SR - Plastic label
0828874

US-EMLP (15X5) CUS - Plastic label
0830076

US-EMLP (15X5) YE CUS - Plastic label
0830077

US-EMLP (15X5) SR CUS - Plastic label0830078
Made to order
UCT-EM (30X5) YE - Marker for end clamp
0830340

UCT-EM (30X5) YE CUS - Marker for end clamp
0830348

MINI MCR-2-PTB - Power terminal block
2902066

MINI MCR-2-PTB-PT - Power terminal block
2902067

QUINT4-SYS-PS/1AC/24DC/2.5/SC - Power supply unit
2904614

MINI MCR-2-FM-RC - Monitoring block
2904504

MINI MCR-2-FM-RC-PT - Monitoring block
2904508

SZS 0,6X3,5 - Screwdriver
1205053